Cisco Systems MGX 8800, MGX 8900 Planning for Bulk Distribution

4-20
Cisco MGX 8800/8900 Series Hardware Installation Guide
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006
Chapter4 Planning for Card Redundancy, Line Redundancy, and Bulk Distribution
Planning for Bulk Distribution
Planning for Bulk Distribution
Bulk distribution is a feature that uses an SRM card to multiplex T1 or E1 traffic from selected service
modules and transmit that traffic over higher speed back cards connected to the SRM. Multiplexed traffic
received at the SRM cards is distributed to the individual service modules. The primary featu re of bulk
AXSM-XG Cards
AXSM-1-9953-XG — — — Slots 1-6, 11-16:
APS connector built in.
AXSM-4-2488-XG — — — Slots 1-6, 11-16:
APS connector built in.
AXSM-8-622-XG Slots 3-6, 10-13:
MGX-8830-APS-CON
Slots 1–6, 9–14:
MGX-8850-APS-CON
MGX-APS-CON2.
— Slots 1-6, 11-16 :
MGX-APS-CON-8950
AXSM-16-155-XG
MPSM-T3E3-155 Slots 3-6, 10-13:
MGX-8830-APS-CON
Slots 1-6, 9-14, 17-22,
25-30:
MGX-8850-APS-CON
——
PXM1E-4-155 Slots 1 and 2:
MGX-8830-APS-CON
Slots 7 and 83:
MGX-8850-APS-CON
MGX-APS-CON4
——
PXM1E-8-155 Slots 1 and 2:
MGX-8830-APS-CON
Slots 7 and 8:
MGX-8850-APS-CON
MGX-APS-CON4
——
PXM1E-
COMBO
Slots 1 and 2:
APS connector built in.
Slots 7 and 8:
APS connector built in.
——
SRME Slots 7 and 14:
MGX-8850-APS-CON
Slots 15,16, 31, 32:
MGX-8850-APS-CON
Slots 15,16, 31, 32:
MGX-8850-APS-CON
—
SRME/B5Slots 7 and 14:
MGX-8850-APS-CON
Slots 15,16, 31, 32:
MGX-8850-APS-CON
Slots 15,16, 31, 32:
MGX-8850-APS-CON
—
VXSM-4-155 — Slots 1-6, 9-14:
MGX-8850-APS-CON
MGX-APS-CON2.
Slots 1, 2, 5, and 6:
APS connector built in.
Slots 3 and 4:
No intercard APS.
Slots 9–14:
MGX-8850-APS-CON
MGX-APS-CON
—
1. MGX 8850/B and 8830/B slots can use an APS-CON only if no RCON is installed.
2. MGX-APS-CON is not supported in the MGX 8850/B chassis. Use the MGX-8850-APS-CON connector instead.
3. MGX 8850 (PXM1E) switches do not require an APS mini-backplane to support intercard APS for PXM1E-4-155. However, Cisco recommends that you
install an APS connectors on PXM1E-4-155 cards to facilitate future upgrades to the PXM1E-8-155.
4. The MGX-APS-CON connector is not supported for use with PXM1E. Use the MGX-8850-APS-CON connector instead.
5. APS connector supported only for the MGX-SMFIR-1-155 and MGX-STM1-EL-1 back cards.
Table4-4 APS Connector Options and Requirements (continued)
Front Card Type MGX 8830 APS Options1MGX8850 APS Options1. MGX 8880 APS Options MGX 8950 APS Options