Contents, Prerequisites for NME-NAM-120S | Cisco Systems SMNMADPTR

Contents

Table 1	Network Analysis Modules (continued)

SKU		Description

NM-NAM		Supports branch routers which include the 2600XM, 2800, 3660, 3700, and
		3800 series multi-services and integrated services routers

WS-SVC-NAM-1		Support the Cisco Catalyst 6500 switches and Cisco 7600 routers

WS-SVC-NAM-2

WS-SVC-NAM-1-250S

WS-SVC-NAM-1-250S

Contents

•Prerequisites for NME-NAM-120S, page 2

•Restrictions for the NME-NAM-120S, page 4

•NAM Software, page 5

•How to Install, Upgrade, or Downgrade NME-NAM-120S, page 7

•Configuring the NME-NAM-120S for Management, page 21

•Managing the NME-NAM-120S, page 48

•Additional References, page 52

•Glossary, page 55

Prerequisites for NME-NAM-120S

The following prerequisites are required to use the NME-NAM-120S module with NAM software.

Supported Branch Routers

The NME-NAM-120S (and NME-NAM-80S) can be deployed in any network module slot in the Cisco router platforms listed in Table 2. A Network Module (NM) Adapter Card, SM-NM-ADPTR, is required to successfully integrate the NME-NAM into supported ISR G2 platforms. The NME-NAM supports the router platforms with NAM software version 3.6 or later. Only one Cisco NAM can be installed in a Cisco branch router.

				Table 2	NME-NAM Supported Router Platforms

							NM Adapter Card
				Router Platform		IOS Version (Minimum)	Required?

				Cisco 3945 ISR		Cisco IOS 15.0(1)M	Yes

				Cisco 3925 ISR		Cisco IOS 15.0(1)M

				Cisco 2951 ISR		Cisco IOS 15.0(1)M

				Cisco 2921 ISR		Cisco IOS 15.0(1)M

				Cisco 2911 ISR		Cisco IOS 15.0(1)M

			Cisco Branch Routers Series Network Analysis Module (NME-NAM-120S) Installation and Configuration Note, 4.0


	2							OL-14942-02
	2							OL-14942-02

Image 2

Cisco Systems SMNMADPTR manual Contents, Prerequisites for NME-NAM-120S

Contents

Series multi-services and integrated services routers Description Contents Prerequisites for NME-NAM-120S Network Modules Router Platform IOS Version Minimum Required? Restrictions for the NME-NAM-120S Upgrade or DowngradeConfiguration File Server NAM Software Monitoring Traffic Through Internal Interface Hardware Interfaces Gateway router From the Host-Router CLI How to Install, Upgrade, or Downgrade NME-NAM-120SSetting Up Network Module Interfaces Ip unnumbered type number Example Command or Action PurposeUsing the commands ip interface internal and ip address Using the commands ip interface external and ip address Examples From the Router CLI Opening a SessionYou can conduct only one session at a time Control-Shift-6 Closing a SessionUse the following steps to close a session From the Router prompt NAM Software Images Upgrading or Reinstalling NAM SoftwareTypes of NAM Software Upgrades Prerequisites Show config Boot helper Boot compactflash From the Service-Module InterfaceConfigure Upgrading the NME-NAM-120S Application Image Full Image Locate the following file Session into the NME-NAM-120S console Enter boot flash Optional Verify your bootloader configuration settingsEnter boot helper Upgrading the NAM Application Image Patch Upgrading the NAM Helper Image NAM CLI FTP server must be reachable from NAM CLI Exit the NAM CLI prompt and get to the NAM loginBecause the exit command closes the session Download and save the NAM helper image to the NAM From the Service Module Interface This section describes how to upgrade the NAM helper imageFrom the Router Enable exec Mode Prompt Upgrading the NAM Helper Image Configure the bootloader to load Reboot the NAMBreak to the NAM bootloader prompt Address, NAM default gateway Boot to the NAM application image Configuring the NME-NAM-120S for ManagementReboot the NAM. By default the NAM will Download helper image from FTP server Enter IOS interface configuration mode Enter IOS exec modeEnter IOS configuration from terminal For the integrated-service-engine NAM management address Setup a full 32-bit static route forExit the router configuration mode Router Configuration Cisco IOS Software Callout Interface Location NAM Configuration NAM Software Integrated-service-engine interface Enter the IOS interface configuration modeFor the integrated-service-engine interface Bring up the integrated-service-engine Router Configuration Cisco IOS Software Configuring the External Interface for Management Enable the loopback interface Enter IOS exec modeEnter IOS configuration from terminal Exit from interface configuration mode Setup the NAM default gateway Address Callout Interface Location Disabling AAA Login Authentication on the NAM Console Line Login authentication list-name End Show running-config Enters global configuration mode Enables privileged Exec modeEnter your password if prompted Creates a local authentication list Ip interface internal external Show ip Configures the NAM system default gateway address Configures the NAM system IP addressOptional Configures the NAM system broadcast address Optional Enables outside logins Configuring the NME-NAM-120S This section provides the following examples What to Do Next Sample Output for the show ip NAM CLI CommandEnabling NAM Packet Monitoring Checking Network Connectivity with Ping Analysis-module monitoring Enable Configure terminal Ip cefEnd Show running-config Correct interfaces Verify that you enabled the Cisco Express ForwardingSwitching path and enabled packet monitoring on This section provides the following example Enabling and Accessing the NAM Traffic Analyzer Ip http server enable or Ip http secure server enable Enter a password Configures a password for the web username Enables the Http serverEnables the Http secure server HTTPs Open a Telnet or SSH session to the NAM. See Accessing the NAM Traffic Analyzer Enabling the NAM Traffic Analyzer Changing the NAM Root Password Password root Changing the NAM Root Password Resetting the NAM Root Password to the Default ValueTroubleshooting Tips Verifying the NAM Root Password Opening and Closing a Telnet or SSH Session to the NAM Enables privileged Exec modeEnter your password if prompted Reloads the software on Exit Logout Telnet PrerequisitesSSH Prerequisites To the NAM and return to the Cisco IOS CLI, complete Leaves a subcommand modeReturn to command mode Managing the NME-NAM-120S Shutting Down and Starting Up NME-NAM-120S Configuration Mode Command Purpose Verifying System Status Configuring Logging Options and Generating Diagnostics Show trace store Additional ReferencesShow trace buffer Trace MIBs MIBs Link MIBsRFCs RFCs Title Description Link Feature Information for Network Analysis ModuleTechnical Assistance Glossary Engine Service module Service engineService or services NetFlow VoIP SyslogTelnet OL-14942-02