From the Router Prompt | Cisco Systems SMNMADPTR specs

Configuring the NME-NAM-120S for Management

NAM Configuration (NAM Software)

root@myNAM.company.com# show ip

IP address:	209.165.200.226
Subnet mask:	255.255.255.224
IP Broadcast:	209.165.200.255
IP Interface:	Internal
DNS Name:	myNAM.company.com
Default Gateway:	209.165.200.225
Nameserver(s):	171.69.2.133
HTTP server:	Enabled
HTTP secure server:	Disabled
HTTP port:	80
HTTP secure port:	443
TACACS+ configured:	No
Telnet:	Enabled
SSH:	Disabled

Configuring the External Interface for Management

This section describes how to configure the NME-NAM-120S to use its external interface for NAM management traffic.

SUMMARY STEPS

From the Router Prompt

1.enable

2.configure terminal

3.interface loopback <loopback-number>

4.ip address <bogus-address> <subnetmask>

5.no shutdown

6.exit

7.interface integrated-service-engine slot/0 or for NM-NAM:

interface analysis-module slot/0

8.ip unnumber loopback <loopback-number>

9.no shutdown

10.service-module external ip address <NAM-Address> <subnetmask>

11.service-module ip default-gateway <NAM-Default-Gateway-Address>

12.end

Cisco Branch Routers Series Network Analysis Module (NME-NAM-120S) Installation and Configuration Note, 4.0

28	OL-14942-02

Image 28

Cisco Systems SMNMADPTR manual Configuring the External Interface for Management, From the Router Prompt

Contents

Series multi-services and integrated services routers Description Contents Prerequisites for NME-NAM-120S Network Modules Router Platform IOS Version Minimum Required? Upgrade or Downgrade ConfigurationRestrictions for the NME-NAM-120S File Server NAM Software Monitoring Traffic Through Internal Interface Hardware Interfaces Gateway router How to Install, Upgrade, or Downgrade NME-NAM-120S Setting Up Network Module InterfacesFrom the Host-Router CLI Ip unnumbered type number Using the commands ip interface internal and ip address Command or Action PurposeExample Using the commands ip interface external and ip address Examples You can conduct only one session at a time Opening a SessionFrom the Router CLI Closing a Session Use the following steps to close a sessionControl-Shift-6 From the Router prompt Upgrading or Reinstalling NAM Software Types of NAM Software UpgradesNAM Software Images Prerequisites From the Service-Module Interface ConfigureShow config Boot helper Boot compactflash Upgrading the NME-NAM-120S Application Image Full Image Locate the following file Session into the NME-NAM-120S console Enter boot helper Optional Verify your bootloader configuration settingsEnter boot flash Upgrading the NAM Application Image Patch Upgrading the NAM Helper Image NAM CLI Exit the NAM CLI prompt and get to the NAM login Because the exit command closes the sessionFTP server must be reachable from NAM CLI Download and save the NAM helper image to the NAM This section describes how to upgrade the NAM helper image From the Router Enable exec Mode PromptFrom the Service Module Interface Upgrading the NAM Helper Image Reboot the NAM Break to the NAM bootloader promptConfigure the bootloader to load Address, NAM default gateway Configuring the NME-NAM-120S for Management Reboot the NAM. By default the NAM willBoot to the NAM application image Download helper image from FTP server Enter IOS exec mode Enter IOS configuration from terminalEnter IOS interface configuration mode For the integrated-service-engine Exit the router configuration mode Setup a full 32-bit static route forNAM management address Router Configuration Cisco IOS Software Callout Interface Location NAM Configuration NAM Software Enter the IOS interface configuration mode For the integrated-service-engine interfaceIntegrated-service-engine interface Bring up the integrated-service-engine Router Configuration Cisco IOS Software Configuring the External Interface for Management Enter IOS exec mode Enter IOS configuration from terminalEnable the loopback interface Exit from interface configuration mode Setup the NAM default gateway Address Callout Interface Location Disabling AAA Login Authentication on the NAM Console Line Login authentication list-name End Show running-config Enables privileged Exec mode Enter your password if promptedEnters global configuration mode Creates a local authentication list Ip interface internal external Show ip Configures the NAM system IP address Optional Configures the NAM system broadcast addressConfigures the NAM system default gateway address Optional Enables outside logins Configuring the NME-NAM-120S This section provides the following examples Sample Output for the show ip NAM CLI Command Enabling NAM Packet MonitoringWhat to Do Next Checking Network Connectivity with Ping End Show running-config Enable Configure terminal Ip cefAnalysis-module monitoring Verify that you enabled the Cisco Express Forwarding Switching path and enabled packet monitoring onCorrect interfaces This section provides the following example Enabling and Accessing the NAM Traffic Analyzer Ip http server enable or Ip http secure server enable Enables the Http server Enables the Http secure server HTTPsEnter a password Configures a password for the web username Open a Telnet or SSH session to the NAM. See Accessing the NAM Traffic Analyzer Enabling the NAM Traffic Analyzer Changing the NAM Root Password Password root Resetting the NAM Root Password to the Default Value Troubleshooting TipsChanging the NAM Root Password Verifying the NAM Root Password Enables privileged Exec mode Enter your password if promptedOpening and Closing a Telnet or SSH Session to the NAM Reloads the software on SSH Prerequisites Telnet PrerequisitesExit Logout Return to command mode Leaves a subcommand modeTo the NAM and return to the Cisco IOS CLI, complete Managing the NME-NAM-120S Shutting Down and Starting Up NME-NAM-120S Configuration Mode Command Purpose Verifying System Status Configuring Logging Options and Generating Diagnostics Additional References Show trace bufferShow trace store Trace MIBs RFCsMIBs MIBs Link RFCs Title Technical Assistance Feature Information for Network Analysis ModuleDescription Link Glossary Service engine Service or servicesEngine Service module NetFlow Telnet SyslogVoIP OL-14942-02