Router Configuration Cisco IOS Software

Configuring the NME-NAM-120S for Management

Figure 2 NAM Management Interface Is Internal and Integrated-Service-Engine Interface Is IP Unnumbered: Sample Topology

Callout	Interface	Location

1	Integrated-Service-Engine interface	Router internal

2	Internal NAM interface (Management)	NME-NAM-120S internal

3	External NAM interface	NME-NAM-120S faceplate

4	Serial interface	WAN interface card (WIC)

5	GigabitEthernet interface	Router rear panel

Router Configuration (Cisco IOS Software)

interface GigabitEthernet0/0

ip address 209.165.200.225 255.255.255.224 duplex auto

speed auto analysis-module monitoring

interface Integrated-Service-Engine2/0 ip unnumbered GigabitEthernet0/0

ip nbar protocol-discovery no keepalive

ip route 209.165.200.226 255.255.255.255 Integrated-Service-Engine2/0

Cisco Branch Routers Series Network Analysis Module (NME-NAM-120S) Installation and Configuration Note, 4.0

24	OL-14942-02

Page 24

Image 24

Cisco Systems SMNMADPTR manual Router Configuration Cisco IOS Software, Callout Interface Location

Contents

Series multi-services and integrated services routers Description Contents Prerequisites for NME-NAM-120S Network Modules Router Platform IOS Version Minimum Required? Upgrade or Downgrade ConfigurationRestrictions for the NME-NAM-120S File Server NAM Software Monitoring Traffic Through Internal Interface Hardware Interfaces Gateway router How to Install, Upgrade, or Downgrade NME-NAM-120S Setting Up Network Module InterfacesFrom the Host-Router CLI Ip unnumbered type number Command or Action Purpose Using the commands ip interface internal and ip addressExample Using the commands ip interface external and ip address Examples Opening a Session You can conduct only one session at a timeFrom the Router CLI Closing a Session Use the following steps to close a sessionControl-Shift-6 From the Router prompt Upgrading or Reinstalling NAM Software Types of NAM Software UpgradesNAM Software Images Prerequisites From the Service-Module Interface ConfigureShow config Boot helper Boot compactflash Upgrading the NME-NAM-120S Application Image Full Image Locate the following file Session into the NME-NAM-120S console Optional Verify your bootloader configuration settings Enter boot helperEnter boot flash Upgrading the NAM Application Image Patch Upgrading the NAM Helper Image NAM CLI Exit the NAM CLI prompt and get to the NAM login Because the exit command closes the sessionFTP server must be reachable from NAM CLI Download and save the NAM helper image to the NAM This section describes how to upgrade the NAM helper image From the Router Enable exec Mode PromptFrom the Service Module Interface Upgrading the NAM Helper Image Reboot the NAM Break to the NAM bootloader promptConfigure the bootloader to load Address, NAM default gateway Configuring the NME-NAM-120S for Management Reboot the NAM. By default the NAM willBoot to the NAM application image Download helper image from FTP server Enter IOS exec mode Enter IOS configuration from terminalEnter IOS interface configuration mode For the integrated-service-engine Setup a full 32-bit static route for Exit the router configuration modeNAM management address Router Configuration Cisco IOS Software Callout Interface Location NAM Configuration NAM Software Enter the IOS interface configuration mode For the integrated-service-engine interfaceIntegrated-service-engine interface Bring up the integrated-service-engine Router Configuration Cisco IOS Software Configuring the External Interface for Management Enter IOS exec mode Enter IOS configuration from terminalEnable the loopback interface Exit from interface configuration mode Setup the NAM default gateway Address Callout Interface Location Disabling AAA Login Authentication on the NAM Console Line Login authentication list-name End Show running-config Enables privileged Exec mode Enter your password if promptedEnters global configuration mode Creates a local authentication list Ip interface internal external Show ip Configures the NAM system IP address Optional Configures the NAM system broadcast addressConfigures the NAM system default gateway address Optional Enables outside logins Configuring the NME-NAM-120S This section provides the following examples Sample Output for the show ip NAM CLI Command Enabling NAM Packet MonitoringWhat to Do Next Checking Network Connectivity with Ping Enable Configure terminal Ip cef End Show running-configAnalysis-module monitoring Verify that you enabled the Cisco Express Forwarding Switching path and enabled packet monitoring onCorrect interfaces This section provides the following example Enabling and Accessing the NAM Traffic Analyzer Ip http server enable or Ip http secure server enable Enables the Http server Enables the Http secure server HTTPsEnter a password Configures a password for the web username Open a Telnet or SSH session to the NAM. See Accessing the NAM Traffic Analyzer Enabling the NAM Traffic Analyzer Changing the NAM Root Password Password root Resetting the NAM Root Password to the Default Value Troubleshooting TipsChanging the NAM Root Password Verifying the NAM Root Password Enables privileged Exec mode Enter your password if promptedOpening and Closing a Telnet or SSH Session to the NAM Reloads the software on Telnet Prerequisites SSH PrerequisitesExit Logout Leaves a subcommand mode Return to command modeTo the NAM and return to the Cisco IOS CLI, complete Managing the NME-NAM-120S Shutting Down and Starting Up NME-NAM-120S Configuration Mode Command Purpose Verifying System Status Configuring Logging Options and Generating Diagnostics Additional References Show trace bufferShow trace store Trace MIBs RFCsMIBs MIBs Link RFCs Title Feature Information for Network Analysis Module Technical AssistanceDescription Link Glossary Service engine Service or servicesEngine Service module NetFlow Syslog TelnetVoIP OL-14942-02