Operating Manual 133 | Fujitsu RX600 S5 specs

CSS components	Non-hot-plug components

Figure 50: Installing the secondary SFP+ transceiver module

ÊIf applicable, install the secondary SFP+ transceiver module accordingly.

RX600 S5

Operating Manual

133

Image 133

Fujitsu RX600 S5 manual Operating Manual 133

Contents

Primergy RX600 S5 Server Copyright and Trademarks Comments… Suggestions… Corrections…Certified documentation according to DIN EN ISO High safety use For your safetyRadio interference Aluminum electrolytic capacitors Harmonic Current Standards Measures against momentary voltage dropOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Operating Manual Contents Control elements and indicators Contents Non-hot-plug components Opening/Closing the server Concept and target groups for this manual Preface Documentation overview Preface Documentation overview Further sources of information Features Preface FeaturesCustomer Self Service CSS Accessible drives/components Battery Backup UnitsSystem board Hot-plug PCI slots Cooling Power supplyHigh level of availability and data security Preface Operating Manual Server management Service and support Features Preface ServerView Installation Manager ServerView Remote Management Electrical data hot-plug power supply unit Technical dataNotational conventions Notational conventions Preface Compliance with regulations and standards Dimensions / Weight Technical dataVentilation clearance Ambient conditions Overview of the installation steps Overview of the installation steps Important information Safety instructions Installation and operation Safety instructionsBefore starting up Important information Safety instructions Batteries Working with CDs/DVDs/BDs and optical drives Never remove parts of the optical drive casing Laser information ESD label Modules with Electrostatic-Sensitive Devices Other important information CE conformity FCC Class a Compliance Statement FCC Class a Compliance Statement Transporting the server For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Environmentally-friendly product design and development Environmental protectionEnergy-saving information Packaging information Labels on plastic casing parts Environmental protectionReturns, recycling and disposal Hours Minimum acclimatization time Unpacking the server Unpacking the server Hardware installation Rack installation/removal of serverRack system requirements Fujitsu rack systems 3rd party racks Rack installation/removal of server Mechanical requirements RX600 S5 Installation in PRIMECENTER/DataCenter rack Fitting the support bracket Fitting the support bracket Installing the support systems Vcaution Inserting the server a Inserting the server For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Installation in 3rd party racks Racks with installation depth smaller/greater than 735 mm Racks with installation depth of 735 mm Connectors on the front Connecting devices to the server Connecting the monitor Connecting devices to the server Installation requirements Connecting the server to the mainsInstallation requirements for AC redundant configurations PSU Configuration Max. DC Loading DC Redundancy Connecting the server to the mains Installation in PRIMECENTER/Datacenter rack Connecting the server to the mains Photo shows installation of a protective earth conductor Cable clamps to secure the power cords Connecting the power cord Disconnecting cables Connecting cables Operating Manual Front of server Control elements and indicators Front detailed view control panel ID card Control elements Starting up and operation Indicators on the control panel Control elements and indicators ServerView Local Service Display Indicators on a hot-plug HDD module Indicators on the hot-plug HDD modules Rear of server Global Error indicator and CSS indicator Control elements and indicators ID indicator ID indicator and button LAN Indicators on the connector panel LAN indicators LAN link/transfer management LAN Indicators on the hot-plug power supply units Control elements and indicators Switching the server on Switching the server on and offStarting up for the first time System already installed Switching the server on and offSwitching the server off Timer-controlled switch-on/off IRMC S2 Configuring the SAS/SATA RAID controller card Configuring the serverConfiguring the server Advantages of the ServerView Installation Manager Installing the operating system Cleaning the server Cleaning the server Bios Setup security functions Mechanical access protection Bios Setup security functions Power cable incorrectly connected Power-on indicator remains unlitPower supply overloaded Screen remains blank Server switches itself off Flickering stripes on monitor screen Troubleshooting and tipsNo screen display or display drifts Monitor does not support the set horizontal frequency RAID controller configuration incorrect Drives reported as dead when starting systemIncorrect date and time Incorrect date and time RAID controller is not configured for this drive Error message on screenAdded drive reported as defective Error message on screen CSS components RX600 S5 Hot-plug components Hot-plug power supply unitsCSS components Hot-plug components Replacing a hot-plug power supply unit Removing a PSU dummy module Adding a hot-plug power supply unit Hot-plug components Identifying the defective CSS component Hot-plug fans Unlocking a fan module and removing it Replacing a defective fan Adding new fans Hot-plug HDD modules Handling drives and HDD/SSD modules 5-inch HDD module and dummy module 3.1 HDD/SSD module and dummy module Removing/installing the 2.5-inch dummy module Removing/installing the dummy module Unlocking the 2.5-inch HDD module Installing the HDD module Removing the HDD module Installing the 2.5-inch HDD module Hot-plug components Hot-plug expansion cards PCI slots with and without hot-plug functionality Slot # Description Deactivating, unlocking and removing the board Removing a hot-plug expansion card Removing the expansion card from the removal tool Removing an expansion card from the removal tool Removing engaging hooks from the removal tool Removing engaging hooks Removing the retaining plate from the removal tool Removing a dummy module Operating Manual 113 Operating the expansion card Hot-plug memory boards Open the server see Opening the server on Identifying the defective memory Removing a defective memory module Removing the memory board in question Removing a memory module Reinstalling the memory board in question Installing a new memory module Removing the memory air baffle to add a memory board Adding a memory board Non-hot-plug components Replacing a non-hot-plug expansion card Identifying the defective CSS componentNon-hot-plug components Removing a non-hot-plug expansion card Take the expansion card out and put it aside Removing engaging hooks Installing a non-hot-plug expansion card Removing an SFP+ transceiver module Replacing SFP+ transceiver modules Operating Manual 127 Removing the SFP+ transceiver Installing SFP+ transceiver modules Inserting the SFP+ transreiver Carefully fold up and latch the locking bail Attaching the protective optical port plug Operating Manual 133 Opening the server Opening/Closing the serverOpening/Closing the server Operating Manual 135 Closing the server Placing the housing cover Processor Memory Modules Configuration Onboard or integrated controllers InterfacesSlots General system information Drive baysOperating Panel Environmental Dimensions Base unit specific Electrical values Appendix server specification 142 Operating Manual Index Energy Star Index Integrated Remote Management 126 Using cable clamps Video connector Voltage Voltage range 148 Operating Manual