Hot-plug components | Fujitsu RX600 S5 guide

Hot-plug components

CSS components

8.1.1.1Replacing a hot-plug power supply unit

Figure 19: Unlocking and removing the power supply unit

VCAUTION!

When replacing a non-defective hot-plug power supply unit in a non- redundant configuration, the server must be switched off first.

ÊRemove the power cord from the cable clamp. You can losen the cable clamp by opening the small locking lever.

ÊRemove the power cord from the installed power supply unit.

ÊPress the green release lever (1) and pull out the power supply unit in the direction of the arrow (2). Grip the handle while pulling the power supply.

VCAUTION!

Release your hands from lever (1) as soon as the power supply unit has been pulled out a few centimeters.

ÊCompletely remove the defective power supply unit from the slot.

VCAUTION!

Never leave the slot for the power supply unit empty for more than two minutes during operation. Otherwise, excessive temperatures could damage system components.

94

Operating Manual

RX600 S5

Image 94

Fujitsu RX600 S5 manual Hot-plug components, Replacing a hot-plug power supply unit

Contents

Primergy RX600 S5 Server Copyright and Trademarks Comments… Suggestions… Corrections…Certified documentation according to DIN EN ISO Radio interference For your safetyHigh safety use Aluminum electrolytic capacitors Harmonic Current Standards Measures against momentary voltage dropOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Operating Manual Contents Contents Control elements and indicators Non-hot-plug components Opening/Closing the server Preface Concept and target groups for this manual Documentation overview Documentation overview Preface Further sources of information Features Preface FeaturesCustomer Self Service CSS System board Battery Backup UnitsAccessible drives/components Hot-plug PCI slots Cooling Power supplyHigh level of availability and data security Preface Operating Manual Server management Features Preface ServerView Installation Manager Service and support ServerView Remote Management Notational conventions Technical dataElectrical data hot-plug power supply unit Notational conventions Preface Compliance with regulations and standards Ventilation clearance Technical dataDimensions / Weight Ambient conditions Overview of the installation steps Overview of the installation steps Safety instructions Important information Installation and operation Safety instructionsBefore starting up Important information Safety instructions Batteries Working with CDs/DVDs/BDs and optical drives Laser information Never remove parts of the optical drive casing Modules with Electrostatic-Sensitive Devices ESD label CE conformity Other important information FCC Class a Compliance Statement FCC Class a Compliance Statement Transporting the server For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Energy-saving information Environmental protectionEnvironmentally-friendly product design and development Packaging information Labels on plastic casing parts Environmental protectionReturns, recycling and disposal Minimum acclimatization time Hours Unpacking the server Unpacking the server Rack system requirements Rack installation/removal of serverHardware installation Fujitsu rack systems Rack installation/removal of server 3rd party racks Mechanical requirements RX600 S5 Installation in PRIMECENTER/DataCenter rack Fitting the support bracket Fitting the support bracket Installing the support systems Vcaution Inserting the server Inserting the server a Installation in 3rd party racks For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Racks with installation depth of 735 mm Racks with installation depth smaller/greater than 735 mm Connecting devices to the server Connectors on the front Connecting devices to the server Connecting the monitor Installation requirements for AC redundant configurations Connecting the server to the mainsInstallation requirements PSU Configuration Max. DC Loading DC Redundancy Connecting the server to the mains Installation in PRIMECENTER/Datacenter rack Connecting the server to the mains Photo shows installation of a protective earth conductor Connecting the power cord Cable clamps to secure the power cords Connecting cables Disconnecting cables Operating Manual Control elements and indicators Front of server ID card Front detailed view control panel Starting up and operation Control elements Control elements and indicators Indicators on the control panel ServerView Local Service Display Indicators on the hot-plug HDD modules Indicators on a hot-plug HDD module Global Error indicator and CSS indicator Rear of server Control elements and indicators ID indicator and button ID indicator Indicators on the connector panel LAN indicators LAN Indicators on the hot-plug power supply units LAN link/transfer management LAN Control elements and indicators Switching the server on Switching the server on and offStarting up for the first time Switching the server off Switching the server on and offSystem already installed Timer-controlled switch-on/off IRMC S2 Configuring the SAS/SATA RAID controller card Configuring the serverConfiguring the server Advantages of the ServerView Installation Manager Installing the operating system Cleaning the server Cleaning the server Mechanical access protection Bios Setup security functions Bios Setup security functions Power cable incorrectly connected Power-on indicator remains unlitPower supply overloaded Server switches itself off Screen remains blank No screen display or display drifts Troubleshooting and tipsFlickering stripes on monitor screen Monitor does not support the set horizontal frequency Incorrect date and time Drives reported as dead when starting systemRAID controller configuration incorrect Incorrect date and time RAID controller is not configured for this drive Error message on screenAdded drive reported as defective Error message on screen CSS components RX600 S5 Hot-plug components Hot-plug power supply unitsCSS components Replacing a hot-plug power supply unit Hot-plug components Adding a hot-plug power supply unit Removing a PSU dummy module Hot-plug components Hot-plug fans Identifying the defective CSS component Replacing a defective fan Unlocking a fan module and removing it Adding new fans Hot-plug HDD modules Handling drives and HDD/SSD modules 3.1 HDD/SSD module and dummy module 5-inch HDD module and dummy module Removing/installing the dummy module Removing/installing the 2.5-inch dummy module Installing the HDD module Unlocking the 2.5-inch HDD module Installing the 2.5-inch HDD module Removing the HDD module Hot-plug components Hot-plug expansion cards Slot # Description PCI slots with and without hot-plug functionality Removing a hot-plug expansion card Deactivating, unlocking and removing the board Removing an expansion card from the removal tool Removing the expansion card from the removal tool Removing engaging hooks Removing engaging hooks from the removal tool Removing a dummy module Removing the retaining plate from the removal tool Operating Manual 113 Operating the expansion card Hot-plug memory boards Identifying the defective memory Open the server see Opening the server on Removing the memory board in question Removing a defective memory module Removing a memory module Installing a new memory module Reinstalling the memory board in question Adding a memory board Removing the memory air baffle to add a memory board Non-hot-plug components Non-hot-plug components Identifying the defective CSS componentReplacing a non-hot-plug expansion card Removing a non-hot-plug expansion card Take the expansion card out and put it aside Removing engaging hooks Installing a non-hot-plug expansion card Replacing SFP+ transceiver modules Removing an SFP+ transceiver module Operating Manual 127 Removing the SFP+ transceiver Installing SFP+ transceiver modules Inserting the SFP+ transreiver Carefully fold up and latch the locking bail Attaching the protective optical port plug Operating Manual 133 Opening the server Opening/Closing the serverOpening/Closing the server Operating Manual 135 Placing the housing cover Closing the server Memory Modules Configuration Processor Onboard or integrated controllers InterfacesSlots General system information Drive baysOperating Panel Dimensions Base unit specific Environmental Electrical values Appendix server specification 142 Operating Manual Index Index Energy Star Integrated Remote Management 126 Using cable clamps Video connector Voltage Voltage range 148 Operating Manual