Installing the operating system | Fujitsu RX600 S5 manual

Configuring the server

Starting up and operation

5.3.3Configuring the server and installing the operating system without the ServerView Installation Manager

Installing the operating system

ÊInsert the CD/DVD/BD for the operating system you want to install.

ÊReboot the server.

ÊFollow the instructions on screen and in the manual for the operating system.

80

Operating Manual

RX600 S5

Image 80

Fujitsu RX600 S5 manual Installing the operating system

Contents

Primergy RX600 S5 Server Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections…Copyright and Trademarks For your safety High safety useRadio interference Aluminum electrolytic capacitors Only for the Japanese market About Sata hard disk drives Measures against momentary voltage dropHarmonic Current Standards Only for the Japanese market Operating Manual Contents Contents Control elements and indicators Non-hot-plug components Opening/Closing the server Preface Concept and target groups for this manual Documentation overview Documentation overview Preface Further sources of information Customer Self Service CSS FeaturesFeatures Preface Battery Backup Units Accessible drives/componentsSystem board Hot-plug PCI slots High level of availability and data security Power supplyCooling Preface Operating Manual Server management Features Preface ServerView Installation Manager Service and support ServerView Remote Management Technical data Electrical data hot-plug power supply unitNotational conventions Notational conventions Preface Compliance with regulations and standards Technical data Dimensions / WeightVentilation clearance Ambient conditions Overview of the installation steps Overview of the installation steps Safety instructions Important information Before starting up Safety instructionsInstallation and operation Important information Safety instructions Batteries Working with CDs/DVDs/BDs and optical drives Laser information Never remove parts of the optical drive casing Modules with Electrostatic-Sensitive Devices ESD label CE conformity Other important information FCC Class a Compliance Statement FCC Class a Compliance Statement Transporting the server For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Environmental protection Environmentally-friendly product design and developmentEnergy-saving information Packaging information Returns, recycling and disposal Environmental protectionLabels on plastic casing parts Minimum acclimatization time Hours Unpacking the server Unpacking the server Rack installation/removal of server Hardware installationRack system requirements Fujitsu rack systems Rack installation/removal of server 3rd party racks Mechanical requirements RX600 S5 Installation in PRIMECENTER/DataCenter rack Fitting the support bracket Fitting the support bracket Installing the support systems Vcaution Inserting the server Inserting the server a Installation in 3rd party racks For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Racks with installation depth of 735 mm Racks with installation depth smaller/greater than 735 mm Connecting devices to the server Connectors on the front Connecting devices to the server Connecting the monitor Connecting the server to the mains Installation requirementsInstallation requirements for AC redundant configurations PSU Configuration Max. DC Loading DC Redundancy Connecting the server to the mains Installation in PRIMECENTER/Datacenter rack Connecting the server to the mains Photo shows installation of a protective earth conductor Connecting the power cord Cable clamps to secure the power cords Connecting cables Disconnecting cables Operating Manual Control elements and indicators Front of server ID card Front detailed view control panel Starting up and operation Control elements Control elements and indicators Indicators on the control panel ServerView Local Service Display Indicators on the hot-plug HDD modules Indicators on a hot-plug HDD module Global Error indicator and CSS indicator Rear of server Control elements and indicators ID indicator and button ID indicator Indicators on the connector panel LAN indicators LAN Indicators on the hot-plug power supply units LAN link/transfer management LAN Control elements and indicators Starting up for the first time Switching the server on and offSwitching the server on Switching the server on and off System already installedSwitching the server off Timer-controlled switch-on/off IRMC S2 Configuring the server Configuring the serverConfiguring the SAS/SATA RAID controller card Advantages of the ServerView Installation Manager Installing the operating system Cleaning the server Cleaning the server Mechanical access protection Bios Setup security functions Bios Setup security functions Power supply overloaded Power-on indicator remains unlitPower cable incorrectly connected Server switches itself off Screen remains blank Troubleshooting and tips Flickering stripes on monitor screenNo screen display or display drifts Monitor does not support the set horizontal frequency Drives reported as dead when starting system RAID controller configuration incorrectIncorrect date and time Incorrect date and time Added drive reported as defective Error message on screenRAID controller is not configured for this drive Error message on screen CSS components RX600 S5 CSS components Hot-plug power supply unitsHot-plug components Replacing a hot-plug power supply unit Hot-plug components Adding a hot-plug power supply unit Removing a PSU dummy module Hot-plug components Hot-plug fans Identifying the defective CSS component Replacing a defective fan Unlocking a fan module and removing it Adding new fans Hot-plug HDD modules Handling drives and HDD/SSD modules 3.1 HDD/SSD module and dummy module 5-inch HDD module and dummy module Removing/installing the dummy module Removing/installing the 2.5-inch dummy module Installing the HDD module Unlocking the 2.5-inch HDD module Installing the 2.5-inch HDD module Removing the HDD module Hot-plug components Hot-plug expansion cards Slot # Description PCI slots with and without hot-plug functionality Removing a hot-plug expansion card Deactivating, unlocking and removing the board Removing an expansion card from the removal tool Removing the expansion card from the removal tool Removing engaging hooks Removing engaging hooks from the removal tool Removing a dummy module Removing the retaining plate from the removal tool Operating Manual 113 Operating the expansion card Hot-plug memory boards Identifying the defective memory Open the server see Opening the server on Removing the memory board in question Removing a defective memory module Removing a memory module Installing a new memory module Reinstalling the memory board in question Adding a memory board Removing the memory air baffle to add a memory board Non-hot-plug components Identifying the defective CSS component Replacing a non-hot-plug expansion cardNon-hot-plug components Removing a non-hot-plug expansion card Take the expansion card out and put it aside Removing engaging hooks Installing a non-hot-plug expansion card Replacing SFP+ transceiver modules Removing an SFP+ transceiver module Operating Manual 127 Removing the SFP+ transceiver Installing SFP+ transceiver modules Inserting the SFP+ transreiver Carefully fold up and latch the locking bail Attaching the protective optical port plug Operating Manual 133 Opening/Closing the server Opening/Closing the serverOpening the server Operating Manual 135 Placing the housing cover Closing the server Memory Modules Configuration Processor Slots InterfacesOnboard or integrated controllers Operating Panel Drive baysGeneral system information Dimensions Base unit specific Environmental Electrical values Appendix server specification 142 Operating Manual Index Index Energy Star Integrated Remote Management 126 Using cable clamps Video connector Voltage Voltage range 148 Operating Manual