Operating Manual | Fujitsu RX600 S5 instruction

Operating Manual

RX600 S5

Image 6

Fujitsu RX600 S5 manual Operating Manual

Contents

Primergy RX600 S5 Server Comments… Suggestions… Corrections… Copyright and TrademarksCertified documentation according to DIN EN ISO Radio interference For your safetyHigh safety use Aluminum electrolytic capacitors Measures against momentary voltage drop Harmonic Current StandardsOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Operating Manual Contents Contents Control elements and indicators Non-hot-plug components Opening/Closing the server Preface Concept and target groups for this manual Documentation overview Documentation overview Preface Further sources of information Features Features PrefaceCustomer Self Service CSS System board Battery Backup UnitsAccessible drives/components Hot-plug PCI slots Power supply CoolingHigh level of availability and data security Preface Operating Manual Server management Features Preface ServerView Installation Manager Service and support ServerView Remote Management Notational conventions Technical dataElectrical data hot-plug power supply unit Notational conventions Preface Compliance with regulations and standards Ventilation clearance Technical dataDimensions / Weight Ambient conditions Overview of the installation steps Overview of the installation steps Safety instructions Important information Safety instructions Installation and operationBefore starting up Important information Safety instructions Batteries Working with CDs/DVDs/BDs and optical drives Laser information Never remove parts of the optical drive casing Modules with Electrostatic-Sensitive Devices ESD label CE conformity Other important information FCC Class a Compliance Statement FCC Class a Compliance Statement Transporting the server For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Energy-saving information Environmental protectionEnvironmentally-friendly product design and development Packaging information Environmental protection Labels on plastic casing partsReturns, recycling and disposal Minimum acclimatization time Hours Unpacking the server Unpacking the server Rack system requirements Rack installation/removal of serverHardware installation Fujitsu rack systems Rack installation/removal of server 3rd party racks Mechanical requirements RX600 S5 Installation in PRIMECENTER/DataCenter rack Fitting the support bracket Fitting the support bracket Installing the support systems Vcaution Inserting the server Inserting the server a Installation in 3rd party racks For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Racks with installation depth of 735 mm Racks with installation depth smaller/greater than 735 mm Connecting devices to the server Connectors on the front Connecting devices to the server Connecting the monitor Installation requirements for AC redundant configurations Connecting the server to the mainsInstallation requirements PSU Configuration Max. DC Loading DC Redundancy Connecting the server to the mains Installation in PRIMECENTER/Datacenter rack Connecting the server to the mains Photo shows installation of a protective earth conductor Connecting the power cord Cable clamps to secure the power cords Connecting cables Disconnecting cables Operating Manual Control elements and indicators Front of server ID card Front detailed view control panel Starting up and operation Control elements Control elements and indicators Indicators on the control panel ServerView Local Service Display Indicators on the hot-plug HDD modules Indicators on a hot-plug HDD module Global Error indicator and CSS indicator Rear of server Control elements and indicators ID indicator and button ID indicator Indicators on the connector panel LAN indicators LAN Indicators on the hot-plug power supply units LAN link/transfer management LAN Control elements and indicators Switching the server on and off Switching the server onStarting up for the first time Switching the server off Switching the server on and offSystem already installed Timer-controlled switch-on/off IRMC S2 Configuring the server Configuring the SAS/SATA RAID controller cardConfiguring the server Advantages of the ServerView Installation Manager Installing the operating system Cleaning the server Cleaning the server Mechanical access protection Bios Setup security functions Bios Setup security functions Power-on indicator remains unlit Power cable incorrectly connectedPower supply overloaded Server switches itself off Screen remains blank No screen display or display drifts Troubleshooting and tipsFlickering stripes on monitor screen Monitor does not support the set horizontal frequency Incorrect date and time Drives reported as dead when starting systemRAID controller configuration incorrect Incorrect date and time Error message on screen RAID controller is not configured for this driveAdded drive reported as defective Error message on screen CSS components RX600 S5 Hot-plug power supply units Hot-plug componentsCSS components Replacing a hot-plug power supply unit Hot-plug components Adding a hot-plug power supply unit Removing a PSU dummy module Hot-plug components Hot-plug fans Identifying the defective CSS component Replacing a defective fan Unlocking a fan module and removing it Adding new fans Hot-plug HDD modules Handling drives and HDD/SSD modules 3.1 HDD/SSD module and dummy module 5-inch HDD module and dummy module Removing/installing the dummy module Removing/installing the 2.5-inch dummy module Installing the HDD module Unlocking the 2.5-inch HDD module Installing the 2.5-inch HDD module Removing the HDD module Hot-plug components Hot-plug expansion cards Slot # Description PCI slots with and without hot-plug functionality Removing a hot-plug expansion card Deactivating, unlocking and removing the board Removing an expansion card from the removal tool Removing the expansion card from the removal tool Removing engaging hooks Removing engaging hooks from the removal tool Removing a dummy module Removing the retaining plate from the removal tool Operating Manual 113 Operating the expansion card Hot-plug memory boards Identifying the defective memory Open the server see Opening the server on Removing the memory board in question Removing a defective memory module Removing a memory module Installing a new memory module Reinstalling the memory board in question Adding a memory board Removing the memory air baffle to add a memory board Non-hot-plug components Non-hot-plug components Identifying the defective CSS componentReplacing a non-hot-plug expansion card Removing a non-hot-plug expansion card Take the expansion card out and put it aside Removing engaging hooks Installing a non-hot-plug expansion card Replacing SFP+ transceiver modules Removing an SFP+ transceiver module Operating Manual 127 Removing the SFP+ transceiver Installing SFP+ transceiver modules Inserting the SFP+ transreiver Carefully fold up and latch the locking bail Attaching the protective optical port plug Operating Manual 133 Opening/Closing the server Opening the serverOpening/Closing the server Operating Manual 135 Placing the housing cover Closing the server Memory Modules Configuration Processor Interfaces Onboard or integrated controllersSlots Drive bays General system informationOperating Panel Dimensions Base unit specific Environmental Electrical values Appendix server specification 142 Operating Manual Index Index Energy Star Integrated Remote Management 126 Using cable clamps Video connector Voltage Voltage range 148 Operating Manual