Removing system fan 1 | Fujitsu TX200 S6 instruction

CSS components

ÊDisconnect the fan cable from the connector FAN2 (if there is a second fan cable, disconnect this from FAN4) on the system board (see the technical manual for the system board D2799).

ÊPress the two green locks of the air duct together (1).

ÊPress the green lock of the air duct in the direction of the arrow (2).

ÊLift the air duct with the integrated system fan 2 (and 4) up and out (3).

8.2.1.3Removing system fan 1 (and 3)

ÊRemove system fan 2 (and 4) (see "Removing system fan 2 (and 4)" on page 105).

Figure 30: System fan 1 and system fan 1&3

The standard system fan 1 is shorter and has just one fan cable; the redundant system fan 1&3 is taller (as 2 fans are integrated internally) and has two fan cables.

The procedure for installing and removing both system fans is identical except for connecting the fan cables.

106

Operating Manual

TX200 S6

Image 106

Fujitsu TX200 S6 manual Removing system fan 1, System fan 1 and system fan 1&3

Contents

Primergy TX200 S6 Server Copyright and Trademarks Comments… Suggestions… Corrections…Certified documentation according to DIN EN ISO Radio interference For your safetyHigh safety use Aluminum electrolytic capacitors Harmonic Current Standards Measures against momentary voltage dropOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Operating Manual Contents Contents Control elements and indicators Screen remains blank Appendix server specification 115 Index 121 Preface Documentation overview Concept and target groups for this manualPreface Preface Further sources of information Features Customer Self Service CSS Trusted Platform Module TPM Preface System boardSlots for expansion cards Preface Hard disk drives For up to eight 2.5-inch SAS/SATA hard disk drives Preface Onboard Sata controller SAS/SATA RAID controller Accessible drives Preface Power supply Cooling Preface High level of availability and data security Preface IRMC S2 with integrated management LAN connector Preface Server management Preface ServerView Installation Manager Service and support Preface ServerView Remote Management Notational conventions Electrical data Technical dataCompliance with regulations and standards Maintenance area for the floorstand model Preface Mechanical specifications Floorstand RackWeight Ventilation clearance TX200 S6 Installation steps, overview Installation steps, overview Safety instructions Important information Installation and operation Important information Before starting up Important information Important information Batteries TX200 S6 Laser information Never remove parts of the optical drive casing ESD label Energy Star Important information Other important information CE conformity FCC Class a Compliance Statement Transporting the server For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Energy-saving information Environmental protectionEnvironmentally-friendly product design and development Packaging information Labels on plastic casing parts Returns, recycling and disposal Minimum acclimatization time Hardware installationHours Hardware installation Unpacking the server Setting up the floorstand model Vcaution Mounting the anti-tilt bracket Mounting the anti-tilt bracket Rack system requirements Installing/removing the rack modelFujitsu rack systems For 19-inch standard rack for the Japanese market 3rd party racks Mechanical requirements TX200 S6 Hardware installation Hardware installation Fitting the support bracket Fitting the support bracket Hardware installation Installing the support systems Insert the server see Inserting the server on Hardware installation Inserting the server Inserting the server a Installation in 3rd party racks Racks with installation depth of 735 mm Racks with installation depth smaller/greater than 735 mm Connecting devices to the server Connector panel on the rear side Connecting the server to the mains Hardware installation Connecting the monitor Connecting the server to the mains Using cable ties Using cable ties Connecting cables Disconnecting cables Hardware installation Access to the accessible drives Access to the drives floorstand modelStarting up and operation Starting up and operation Removing the drive cover from the hard disk drive cover Access to the HDD modules Removing the hard disk cover Control elements and indicators Front of server Starting up and operation ID card Control elements Starting up and operation LEDs on the control panel Indicators on the drives DVD drive activity indicator Starting up and operation Hard disk drive indicators Indicators on the 3.5 inch and 2.5 inch HDD modules Rear of server Starting up and operation LAN transfer rate indicator management LAN Starting up and operation LAN indicatorsLAN activity indicator management LAN LAN activity indicator shared LAN Indicators on the hot-plug power supply units System already installed Switching the server on and offSwitching the server on Switching the server off After power failure Timer-controlled switch-on/offRing indicator Power button override Configuring the onboard Sata controller Configuring the serverConfiguring the SAS/SATA RAID controller Advantages of the ServerView Installation Manager LSI RAID / Scsi Controllers Configure onboard Sata controller Installing the operating system Cleaning the server Bios Setup security functions Property and data protection Property and data protection Power cable incorrectly connected Troubleshooting and tipsPower-on indicator remains unlit Power supply overloaded Server switches itself off Screen remains blank No screen display or display drifts Flickering stripes on monitor screenMonitor does not support the set horizontal frequency RAID controller configuration incorrect Drives reported as dead when starting systemIncorrect date and time RAID controller is not configured for this drive Error message on screenAdded drive reported as defective Page CSS components Hot-plug components Hot-plug power supply units optionalReplacing the hot-plug power supply unit CSS components Hot-plug hard disk drives CSS components For description see section Hard disk drive indicators on CSS components 2.1 3.5-inch HDD module and dummy module CSS components 2.2 2.5-inch HDD module and dummy module CSS components Handling hard disk drives and HDD modules CSS components Floorstand removing the hard disk cover CSS components Removing/installing the dummy module Unlocking the 3.5-inch and 2.5-inch HDD modules CSS components Installing the HDD module Installing the 3.5-inch and 2.5-inch HDD modules CSS components Removing the HDD module Non-hot-plug components Open the server see section Opening the server on Opening the server Opening the server example floorstand model CSS components Removing system fan 2 System fan 2 and system fan 2&4 Removing system fan 1 System fan 1 and system fan 1&3 Identifying a CSS component Example Removing system fan 1&3 Replacing a memory module Installing a new memory moduleRemoving a defective memory module Replacing system fan 2 Replacing the system fanReplacing system fan 1 Replacing an expansion card Removing a defective expansion card CSS components Installing a new expansion card Installing a new expansion card Reinstalling the fans and closing the server Installing system fan 1 CSS components Installing system fan 2 Installing system fan 2 CSS components Closing the server Closing the server example floorstand model Processor Appendix server specificationMemory Modules Configuration Interfaces Appendix server specification Onboard or integrated controllers Drive bays PCI-SlotsOperating Panel Dimensions Base unit specific Environmental Electrical values 120 Operating Manual Bios Index Index Labels LAN activity indicator Sddc Unpacking, server USB connector