Identifying a CSS component | Fujitsu TX200 S6 specification

CSS components

Figure 31: Example: Removing system fan 1&3

ÊDisconnect the fan cable from the connector FAN1 on the system board (if there is a second fan cable, disconnect this from FAN3).

ÊPush the locking lever in the direction of the arrow (1).

ÊPull system fan 1 (and 3) in the direction of the arrow (2) to disengage the four hooks.

ÊTake system fan 1 (and 3) out (3).

8.2.1.4Identifying a CSS component

ÊPress the Indicate CSS button on the system board (see the technical manual for the system board D2799).

The PRIMERGY Diagnostic LED of the defective CSS component lights up orange, thereby indicating which CSS component (memory module, fan or expansion card) on the system board must be replaced (see technical manual for the system board D2799).

TX200 S6

Operating Manual

107

Image 107

Fujitsu TX200 S6 manual Identifying a CSS component, Example Removing system fan 1&3

Contents

Primergy TX200 S6 Server Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections…Copyright and Trademarks Aluminum electrolytic capacitors For your safetyHigh safety use Radio interference Only for the Japanese market About Sata hard disk drives Measures against momentary voltage dropHarmonic Current Standards Only for the Japanese market Operating Manual Contents Control elements and indicators Contents Screen remains blank Appendix server specification 115 Index 121 Preface Preface Concept and target groups for this manualDocumentation overview Preface Further sources of information Customer Self Service CSS Features Slots for expansion cards Preface System boardTrusted Platform Module TPM For up to eight 2.5-inch SAS/SATA hard disk drives Preface Hard disk drives SAS/SATA RAID controller Preface Onboard Sata controller Accessible drives Cooling Preface Power supply Preface High level of availability and data security Preface IRMC S2 with integrated management LAN connector Preface Server management Service and support Preface ServerView Installation Manager Preface ServerView Remote Management Notational conventions Compliance with regulations and standards Technical dataElectrical data Ventilation clearance Preface Mechanical specifications Floorstand RackWeight Maintenance area for the floorstand model TX200 S6 Installation steps, overview Installation steps, overview Important information Safety instructions Important information Before starting up Installation and operation Important information Important information Batteries TX200 S6 Never remove parts of the optical drive casing Laser information ESD label Important information Other important information Energy Star FCC Class a Compliance Statement CE conformity Transporting the server For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Packaging information Environmental protectionEnvironmentally-friendly product design and development Energy-saving information Returns, recycling and disposal Labels on plastic casing parts Hours Hardware installationMinimum acclimatization time Unpacking the server Hardware installation Vcaution Setting up the floorstand model Mounting the anti-tilt bracket Mounting the anti-tilt bracket Fujitsu rack systems Installing/removing the rack modelRack system requirements 3rd party racks For 19-inch standard rack for the Japanese market Mechanical requirements TX200 S6 Hardware installation Fitting the support bracket Hardware installation Fitting the support bracket Hardware installation Installing the support systems Insert the server see Inserting the server on Inserting the server a Hardware installation Inserting the server Installation in 3rd party racks Racks with installation depth smaller/greater than 735 mm Racks with installation depth of 735 mm Connector panel on the rear side Connecting devices to the server Hardware installation Connecting the monitor Connecting the server to the mains Connecting the server to the mains Using cable ties Using cable ties Disconnecting cables Connecting cables Hardware installation Starting up and operation Access to the drives floorstand modelAccess to the accessible drives Removing the drive cover from the hard disk drive cover Starting up and operation Removing the hard disk cover Access to the HDD modules Front of server Control elements and indicators Control elements Starting up and operation ID card Starting up and operation LEDs on the control panel Indicators on the drives DVD drive activity indicator Indicators on the 3.5 inch and 2.5 inch HDD modules Starting up and operation Hard disk drive indicators Rear of server Starting up and operation LAN activity indicator shared LAN Starting up and operation LAN indicatorsLAN activity indicator management LAN LAN transfer rate indicator management LAN Indicators on the hot-plug power supply units Switching the server off Switching the server on and offSwitching the server on System already installed Power button override Timer-controlled switch-on/offRing indicator After power failure Configuring the SAS/SATA RAID controller Configuring the serverConfiguring the onboard Sata controller LSI RAID / Scsi Controllers Advantages of the ServerView Installation Manager Installing the operating system Configure onboard Sata controller Cleaning the server Property and data protection Bios Setup security functions Property and data protection Power supply overloaded Troubleshooting and tipsPower-on indicator remains unlit Power cable incorrectly connected Screen remains blank Server switches itself off Monitor does not support the set horizontal frequency Flickering stripes on monitor screenNo screen display or display drifts Incorrect date and time Drives reported as dead when starting systemRAID controller configuration incorrect Added drive reported as defective Error message on screenRAID controller is not configured for this drive Page CSS components CSS components Hot-plug power supply units optionalReplacing the hot-plug power supply unit Hot-plug components Hot-plug hard disk drives CSS components CSS components 2.1 3.5-inch HDD module and dummy module For description see section Hard disk drive indicators on CSS components 2.2 2.5-inch HDD module and dummy module CSS components Handling hard disk drives and HDD modules CSS components Floorstand removing the hard disk cover CSS components Removing/installing the dummy module Unlocking the 3.5-inch and 2.5-inch HDD modules Installing the 3.5-inch and 2.5-inch HDD modules CSS components Installing the HDD module CSS components Removing the HDD module Open the server see section Opening the server on Non-hot-plug components Opening the server example floorstand model Opening the server System fan 2 and system fan 2&4 CSS components Removing system fan 2 System fan 1 and system fan 1&3 Removing system fan 1 Example Removing system fan 1&3 Identifying a CSS component Removing a defective memory module Installing a new memory moduleReplacing a memory module Replacing system fan 1 Replacing the system fanReplacing system fan 2 Removing a defective expansion card Replacing an expansion card Installing a new expansion card CSS components Installing a new expansion card Installing system fan 1 Reinstalling the fans and closing the server Installing system fan 2 CSS components Installing system fan 2 Closing the server example floorstand model CSS components Closing the server Interfaces Appendix server specificationMemory Modules Configuration Processor Onboard or integrated controllers Appendix server specification Operating Panel PCI-SlotsDrive bays Environmental Dimensions Base unit specific Electrical values 120 Operating Manual Index Bios Index Labels LAN activity indicator Sddc Unpacking, server USB connector