Added drive reported as defective | Fujitsu TX200 S6 guide

Troubleshooting and tips

7.8Added drive reported as defective

RAID controller is not configured for this drive

The drive was probably installed when the system was switched off.

ÊReconfigure the RAID controller for the drive using the corresponding utility. Information is provided in the documentation for the RAID controller.

or

ÊRemove and reinstall the drive while the system is switched ON.

If the hard disk drive continues to be shown as defective, then replace it (see "Hot-plug hard disk drives" on page 93).

7.9Error message on screen

The meaning of the error message is explained in the documentation for the relevant components and programs on the ServerView Suite DVD 2.

TX200 S6

Operating Manual

89

Image 89

Fujitsu TX200 S6 manual Added drive reported as defective, Error message on screen

Contents

Primergy TX200 S6 Server Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections…Copyright and Trademarks High safety use For your safetyRadio interference Aluminum electrolytic capacitors Only for the Japanese market About Sata hard disk drives Measures against momentary voltage dropHarmonic Current Standards Only for the Japanese market Operating Manual Contents Control elements and indicators Contents Screen remains blank Appendix server specification 115 Index 121 Preface Preface Concept and target groups for this manualDocumentation overview Preface Further sources of information Customer Self Service CSS Features Slots for expansion cards Preface System boardTrusted Platform Module TPM For up to eight 2.5-inch SAS/SATA hard disk drives Preface Hard disk drives SAS/SATA RAID controller Preface Onboard Sata controller Accessible drives Cooling Preface Power supply Preface High level of availability and data security Preface IRMC S2 with integrated management LAN connector Preface Server management Service and support Preface ServerView Installation Manager Preface ServerView Remote Management Notational conventions Compliance with regulations and standards Technical dataElectrical data Weight Preface Mechanical specifications Floorstand RackMaintenance area for the floorstand model Ventilation clearance TX200 S6 Installation steps, overview Installation steps, overview Important information Safety instructions Important information Before starting up Installation and operation Important information Important information Batteries TX200 S6 Never remove parts of the optical drive casing Laser information ESD label Important information Other important information Energy Star FCC Class a Compliance Statement CE conformity Transporting the server For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Environmentally-friendly product design and development Environmental protectionEnergy-saving information Packaging information Returns, recycling and disposal Labels on plastic casing parts Hours Hardware installationMinimum acclimatization time Unpacking the server Hardware installation Vcaution Setting up the floorstand model Mounting the anti-tilt bracket Mounting the anti-tilt bracket Fujitsu rack systems Installing/removing the rack modelRack system requirements 3rd party racks For 19-inch standard rack for the Japanese market Mechanical requirements TX200 S6 Hardware installation Fitting the support bracket Hardware installation Fitting the support bracket Hardware installation Installing the support systems Insert the server see Inserting the server on Inserting the server a Hardware installation Inserting the server Installation in 3rd party racks Racks with installation depth smaller/greater than 735 mm Racks with installation depth of 735 mm Connector panel on the rear side Connecting devices to the server Hardware installation Connecting the monitor Connecting the server to the mains Connecting the server to the mains Using cable ties Using cable ties Disconnecting cables Connecting cables Hardware installation Starting up and operation Access to the drives floorstand modelAccess to the accessible drives Removing the drive cover from the hard disk drive cover Starting up and operation Removing the hard disk cover Access to the HDD modules Front of server Control elements and indicators Control elements Starting up and operation ID card Starting up and operation LEDs on the control panel Indicators on the drives DVD drive activity indicator Indicators on the 3.5 inch and 2.5 inch HDD modules Starting up and operation Hard disk drive indicators Rear of server Starting up and operation LAN activity indicator management LAN Starting up and operation LAN indicatorsLAN transfer rate indicator management LAN LAN activity indicator shared LAN Indicators on the hot-plug power supply units Switching the server on Switching the server on and offSystem already installed Switching the server off Ring indicator Timer-controlled switch-on/offAfter power failure Power button override Configuring the SAS/SATA RAID controller Configuring the serverConfiguring the onboard Sata controller LSI RAID / Scsi Controllers Advantages of the ServerView Installation Manager Installing the operating system Configure onboard Sata controller Cleaning the server Property and data protection Bios Setup security functions Property and data protection Power-on indicator remains unlit Troubleshooting and tipsPower cable incorrectly connected Power supply overloaded Screen remains blank Server switches itself off Monitor does not support the set horizontal frequency Flickering stripes on monitor screenNo screen display or display drifts Incorrect date and time Drives reported as dead when starting systemRAID controller configuration incorrect Added drive reported as defective Error message on screenRAID controller is not configured for this drive Page CSS components Replacing the hot-plug power supply unit Hot-plug power supply units optionalHot-plug components CSS components Hot-plug hard disk drives CSS components CSS components 2.1 3.5-inch HDD module and dummy module For description see section Hard disk drive indicators on CSS components 2.2 2.5-inch HDD module and dummy module CSS components Handling hard disk drives and HDD modules CSS components Floorstand removing the hard disk cover CSS components Removing/installing the dummy module Unlocking the 3.5-inch and 2.5-inch HDD modules Installing the 3.5-inch and 2.5-inch HDD modules CSS components Installing the HDD module CSS components Removing the HDD module Open the server see section Opening the server on Non-hot-plug components Opening the server example floorstand model Opening the server System fan 2 and system fan 2&4 CSS components Removing system fan 2 System fan 1 and system fan 1&3 Removing system fan 1 Example Removing system fan 1&3 Identifying a CSS component Removing a defective memory module Installing a new memory moduleReplacing a memory module Replacing system fan 1 Replacing the system fanReplacing system fan 2 Removing a defective expansion card Replacing an expansion card Installing a new expansion card CSS components Installing a new expansion card Installing system fan 1 Reinstalling the fans and closing the server Installing system fan 2 CSS components Installing system fan 2 Closing the server example floorstand model CSS components Closing the server Memory Modules Configuration Appendix server specificationProcessor Interfaces Onboard or integrated controllers Appendix server specification Operating Panel PCI-SlotsDrive bays Environmental Dimensions Base unit specific Electrical values 120 Operating Manual Index Bios Index Labels LAN activity indicator Sddc Unpacking, server USB connector