Manuals / Fujitsu / Computer Equipment / Server

Fujitsu TX200 S6 manual Replacing the system fan, Replacing system fan 2, Replacing system fan 1

Models: TX200 S6

1 126

Download 126 pages 61.66 Kb

Page 109

CSS components

8.2.3Replacing the system fan

VCAUTION!

Since the standard system fans 1 and 2 are not redundant, these system fans have to be replaced immediately.

If one of the four redundant system fans (1&3 and 2&4) fails, one of the two predetermined fans (system fan 3 and 4) increases its power to ensure that the server is cooled properly. The redundant system fans should be replaced as soon as possible.

8.2.3.1Replacing system fan 2 (and 4)

ÊRemove the defective system fan 2 (and 4) (see "Removing system fan 2 (and 4)" on page 105).

ÊInstall the new system fan 2 (and 4) (see "Installing system fan 2 (and 4)" on page 113).

8.2.3.2Replacing system fan 1 (and 3)

ÊRemove the defective system fan 1 (and 3) (see "Removing system fan 1 (and 3)" on page 106).

ÊInstall the new system fan 1 (and 3) (see "Installing system fan 1 (and 3)" on page 112).

TX200 S6

Operating Manual

109

Image 109

Fujitsu TX200 S6 manual Replacing the system fan, Replacing system fan 2, Replacing system fan 1

Contents

Primergy TX200 S6 Server Copyright and Trademarks Comments… Suggestions… Corrections…Certified documentation according to DIN EN ISO High safety use For your safetyRadio interference Aluminum electrolytic capacitorsHarmonic Current Standards Measures against momentary voltage dropOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Operating Manual Contents Control elements and indicators ContentsScreen remains blank Appendix server specification 115 Index 121 Preface Documentation overview Concept and target groups for this manualPreface Preface Further sources of information Customer Self Service CSS FeaturesTrusted Platform Module TPM Preface System boardSlots for expansion cards For up to eight 2.5-inch SAS/SATA hard disk drives Preface Hard disk drivesSAS/SATA RAID controller Preface Onboard Sata controllerAccessible drives Cooling Preface Power supplyPreface High level of availability and data security Preface IRMC S2 with integrated management LAN connector Preface Server management Service and support Preface ServerView Installation ManagerPreface ServerView Remote Management Notational conventions Electrical data Technical dataCompliance with regulations and standards Weight Preface Mechanical specifications Floorstand RackMaintenance area for the floorstand model Ventilation clearanceTX200 S6 Installation steps, overview Installation steps, overview Important information Safety instructionsImportant information Before starting up Installation and operationImportant information Important information Batteries TX200 S6 Never remove parts of the optical drive casing Laser informationESD label Important information Other important information Energy StarFCC Class a Compliance Statement CE conformityTransporting the server For the Japanese market, please refer to 安全上の注意およびその他の重要情報 Environmentally-friendly product design and development Environmental protectionEnergy-saving information Packaging informationReturns, recycling and disposal Labels on plastic casing partsMinimum acclimatization time Hardware installationHours Unpacking the server Hardware installationVcaution Setting up the floorstand modelMounting the anti-tilt bracket Mounting the anti-tilt bracketRack system requirements Installing/removing the rack modelFujitsu rack systems 3rd party racks For 19-inch standard rack for the Japanese marketMechanical requirements TX200 S6 Hardware installation Fitting the support bracket Hardware installation Fitting the support bracketHardware installation Installing the support systems Insert the server see Inserting the server on Inserting the server a Hardware installation Inserting the serverInstallation in 3rd party racks Racks with installation depth smaller/greater than 735 mm Racks with installation depth of 735 mmConnector panel on the rear side Connecting devices to the serverHardware installation Connecting the monitor Connecting the server to the mainsConnecting the server to the mains Using cable ties Using cable tiesDisconnecting cables Connecting cablesHardware installation Access to the accessible drives Access to the drives floorstand modelStarting up and operation Removing the drive cover from the hard disk drive cover Starting up and operationRemoving the hard disk cover Access to the HDD modulesFront of server Control elements and indicatorsControl elements Starting up and operation ID cardStarting up and operation LEDs on the control panel Indicators on the drives DVD drive activity indicator Indicators on the 3.5 inch and 2.5 inch HDD modules Starting up and operation Hard disk drive indicatorsRear of server Starting up and operation LAN activity indicator management LAN Starting up and operation LAN indicatorsLAN transfer rate indicator management LAN LAN activity indicator shared LANIndicators on the hot-plug power supply units Switching the server on Switching the server on and offSystem already installed Switching the server offRing indicator Timer-controlled switch-on/offAfter power failure Power button overrideConfiguring the onboard Sata controller Configuring the serverConfiguring the SAS/SATA RAID controller LSI RAID / Scsi Controllers Advantages of the ServerView Installation ManagerInstalling the operating system Configure onboard Sata controllerCleaning the server Property and data protection Bios Setup security functionsProperty and data protection Power-on indicator remains unlit Troubleshooting and tipsPower cable incorrectly connected Power supply overloadedScreen remains blank Server switches itself offNo screen display or display drifts Flickering stripes on monitor screenMonitor does not support the set horizontal frequency RAID controller configuration incorrect Drives reported as dead when starting systemIncorrect date and time RAID controller is not configured for this drive Error message on screenAdded drive reported as defective Page CSS components Replacing the hot-plug power supply unit Hot-plug power supply units optionalHot-plug components CSS componentsHot-plug hard disk drives CSS components CSS components 2.1 3.5-inch HDD module and dummy module For description see section Hard disk drive indicators onCSS components 2.2 2.5-inch HDD module and dummy module CSS components Handling hard disk drives and HDD modules CSS components Floorstand removing the hard disk cover CSS components Removing/installing the dummy module Unlocking the 3.5-inch and 2.5-inch HDD modules Installing the 3.5-inch and 2.5-inch HDD modules CSS components Installing the HDD moduleCSS components Removing the HDD module Open the server see section Opening the server on Non-hot-plug componentsOpening the server example floorstand model Opening the serverSystem fan 2 and system fan 2&4 CSS components Removing system fan 2System fan 1 and system fan 1&3 Removing system fan 1Example Removing system fan 1&3 Identifying a CSS componentReplacing a memory module Installing a new memory moduleRemoving a defective memory module Replacing system fan 2 Replacing the system fanReplacing system fan 1 Removing a defective expansion card Replacing an expansion cardInstalling a new expansion card CSS components Installing a new expansion cardInstalling system fan 1 Reinstalling the fans and closing the serverInstalling system fan 2 CSS components Installing system fan 2Closing the server example floorstand model CSS components Closing the serverMemory Modules Configuration Appendix server specificationProcessor InterfacesOnboard or integrated controllers Appendix server specificationDrive bays PCI-SlotsOperating Panel Environmental Dimensions Base unit specificElectrical values 120 Operating Manual Index BiosIndex Labels LAN activity indicator Sddc Unpacking, server USB connector