5. CUSTOMIZING YOUR UNIT

Contents of GPS sensor setup menu (con’t from previous page)

Item

Description

Settings

 

Default Setting

Spd/Cse

During position fixing, ship’s velocity (speed and course)

0-999 sec

 

5 sec

Smoothing

is directly measured by receiving GPS satellite signals.

 

 

 

 

The raw velocity data may vary too much depending on

 

 

 

 

receiving conditions and other factors. You can reduce

 

 

 

 

this variance by increasing the smoothing. Like with

 

 

 

 

latitude and longitude smoothing, the higher the speed

 

 

 

 

and course smoothing the higher the smoothing setting,

 

 

 

 

the more the raw data will be averaged. If this setting is

 

 

 

 

high, the response to speed and course changes will

 

 

 

 

slow. For no smoothing, enter all zeros.

 

 

 

GPS Speed

Calculation of ETA is based on average ship’s speed

0-999 sec

 

60 sec

Averaging

over a given period. If the period is too long or too short,

 

 

 

 

calculation error will result. Change this setting if

 

 

 

 

calculation error occurs. The default setting is suitable for

 

 

 

 

most conditions.

 

 

 

Latitude,

Offsets latitude position to further refine position

0.001’S – 9.999’N

 

0.0’ (no offset)

Longitude

accuracy. Use the N<− −> S soft key to switch

0.001’E – 9.999’W

 

 

Offset

coordinate.

 

 

 

Disable

Every GPS satellite is broadcasting abnormal satellite

 

 

None

Satellite

number(s) in its Almanac, which contains general orbital

 

 

 

 

data about all GPS satellites, including those which are

 

 

 

 

malfunctioning. Using this information, the GPS receiver

 

 

 

 

automatically eliminates any malfunctioning satellite from

 

 

 

 

the GPS satellite schedule. However, the Almanac

 

 

 

 

sometimes may not contain this information. If you hear

 

 

 

 

about a malfunctioning satellite from another source, you

 

 

 

 

can disable it manually. Enter satellite number (two digits,

 

 

 

 

max. 3 satellites) with the trackball and [ENTER] knob

 

 

 

 

and press the ENTER soft key.

 

 

 

Latitude

Sets initial latitude position after cold start. Use the

 

°

 

 

45 35.000’N

 

N< − −> S soft key to switch coordinate.

 

 

 

Longitude

Sets initial longitude position after cold start. Use the

 

°

 

 

125 00.000’W

 

W< − −> E soft key to switch coordinate.

 

 

 

Antenna

Enters the height of the GPS antenna unit above sea

0-99 m

 

5 m

Height

surface. For further details refer to the installation

 

 

 

 

manual.

 

 

 

GPS Fix

Chooses position fixing method: 2D (three satellites in

2D, 2D/3D

 

2D/3D

Mode

view), 2D/3D (three or four satellites in view whichever is

 

 

 

 

greater).

 

 

 

Cold Start

Clears the Almanac to receive the latest Almanac.

No, Yes

 

No

GPS STATUS

Displays GPS satellite status display. Requires GPS Receiver GP-310/320B or GPS navigator outputting

(soft key)

the data sentence GSA or GSV. For further details see the chapter on Maintenance.

 

5-25

Page 197
Image 197
Furuno 1742, 1753C, 1733C, 1752, 1723C, 1762C, 1732, 1722C Contents of GPS sensor setup menu con’t from previous, GPS Status