Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny 680 KFC Roll Unit Off Pallet Onto Ramp, Orient Casters In Sideways, To Unlatch Lid

Models: 680 KFC

1 109

Download 109 pages 54.87 Kb

Page 12

05 ROLL UNIT OFF PALLET ONTO RAMP.

05 ROLL UNIT OFF PALLET ONTO RAMP.

ORIENT CASTERS IN SIDEWAYS

POSITION. RAISE SIDE SLIGHTLY 8 KNOCK OUT RUBBER PADS (2). -

TYPICAL BOTH SIDES

HH

BA5KET D TRAYS

REMOVE REAR COVER -

WEIGHT SEGMENTS

MUST BE INSTALLED

PER INSTRUCTIONS

CONTAINED THEREIN

BEFORE ATTEMPTING

TO UNLATCH LID.

f-01 REMOVE ACCESSORY BOXES FROM FRONT.

PROP UP A RAMP FOR EACH CASTER ON THE SELECTED SIDE.

Image 12

Henny Penny 680 KFC manual Roll Unit Off Pallet Onto Ramp, Orient Casters In Sideways, Typical Both Sides, To Unlatch Lid

Contents

Page SPECIFICATIONS HENNY PENNY 8 HEAD GAS PRESSURE FRYERModel 680 Gas Fryer Page Page LIMITED WARRANTY FOR HENNY PENNY APPLIANCES Henny PennySection Section PageSECTION 1. INTRODUCTION 1-1.PRESSURE FRYERP-H-T PRESSUREThe word DANGER indicates an imminent hazard which will result in highly serious injury such as second or third degree burns, loss of sight, and other perma- nent injuries 7.Load the Counterweight Assembly. See page 10.Prepare the deadweight valve for operationB . Remove the round weight 1.Cut and remove the metal bands from the cartonD.Clean the orifice with a dry cloth E.Replace the weight and secure the top capC.Remove and discard the shipping support REMOVE REAR COVER WEIGHT SEGMENTS MUST BE INSTALLED PER INSTRUCTIONSf-01REMOVE ACCESSORY BOXES FROM FRONT 05 ROLL UNIT OFF PALLET ONTO RAMPm EACH WEIGHT SEGMENT WEIGHS APPROXIMATELY INSERT~TH a SEGMENTPage To avoid possible serious personal injury Do not use cast iron fittings i CAUTION # ALL STR N Natural: 3.5 inches water column FILTER ONLY WHEN “COOL” IS DISPLAYED Power/Pump Gauge Solenoid Valve Drain Valve To close lid 3.Lift up on the lid handle until it stops4.Bring lid handle out towards you until it stops 5.Push lid handle down, locking lid in placeTo open lid 3-4.SWITCHES AND INDICATORS“Lo” Mode “Cool” Modeto “Drop” In the event of a power failure, no attempt should be made to operate the fryer. The Model 680 Fryer is equipped with an automatic ignition system and can not be operated without electrical power 1. Turn the main power switch to “OFF” Page Page To shutdown burner hj i’:.;,‘i ,e:::;.*f To isolate a malfunction, proceed as follows Product Color D. Spotted D. Rancid Taste Pressure will not Pressure does not build Shortening will not heat. “E20” Heating of shortening too slow or boil Gasket coming out of lid Removing 1. Remove electrical power supplied to the fryer 6.Straighten the capillary tube 1.Remove Control Panel 1. Remove electrical power supplied to the fryer 11.Turn power “ON” and check out fryer2.Drain the shortening from the cookpot 3.Remove the Control Panel5-7COMPLETE CONTROL PANEL - HENNY PENNY5-8PRESSURE REGULATION Every 90 days1.Lower the lid assembly 3.Clean the gasket and gasket seat with hot water 4.Thread a 5116” nut on each end of the new cable 5-11.LID COUNTERWEIGHT CONT’D 5-12.PRESSURE PAD5-13.LID ADJUSTMENT Henny PennyModel 1005Hertz 2.Remove the cover Replacement Continued 5-16.SOLENOID VALVE5-17.OPERATING CONTROL VALVEDO NOT MANUALLYACTIVATE THE SAFETY Cleaning Steps5-18.REMOVAL & CLEANING OF SAFETY VALVEContinued 5-19.PRESSURE GAUGECalibration Steps 5-18.REMOVAL & CLEANING9.Remove wires from control valve 1.Turn gas cock knob to the “OFF” position2.Pull gas cock knob from control valve 3.Remove cover from control valve12.Reassemble in reverse order 1.Remove both side panels 1. Remove electrical power supplied to the unit 4.Remove the wires from transformer5. Replace with new transformer in reverse order 1. Remove electrical power supplied to the unit 2.Remove small access panel from right side panel3.Pull hose from switch from under fryer 4.Disconnect wires from switch1. Remove electrical power supplied to the unit 2.Remove small access panel from right side panel3.Remove wires from modules 5.Install new module in reverse order1.Remove both side panels of unit 1.Remove electrical power supplied to the unit 2.Using l/4” socket remove the left side panelA.Both burners the same color, but not orangy-red 4.Mark the shield in the postion it is inLeft ‘Burner 6.Remove air hose gas valve 3.Locate wire nuts and disconnect leads Page 11.Secure the strips to the weights epyg-uinuebq plea ewy Page 2.Depress the “Select Time” button PROB - Temperature probe has failed 1.Enter the special program mode Product One FIGURE 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 35092 Page Not Avail e 1 L FIGURE Henny Penny Model6-12 1005FIGURE Page FIGURE Page FIGURE Page FIGURE Page FIGURE NOTE: ASSEMBLE CORE DISC ASSEMBLY WITH SMOOTH AND ROUNDED EDGE OF BLADETOWARD DISC SPRING GUIDE ITEM NOTE: DO NOT DAMAGE SEAT IN ANY WAYFIGURE J2OV, JPH, 2 WIRE W/GRr;iC& 1 VACI511ti ‘”8-HEADGAS COOKER 72OV, If/-l,2 WIRE W/GRND I I I I SIE.8-HEADGAS COOKER PRESSURE 1l-Q?Y IAy--4A-<+-7 MODEL 680 GAS FRYERN i I 1 \1 23 IHenny Penny Model6-27 Henny Penny Model6-28 Henny Penny Model6-29 Henny Penny Model6-30 SMS PROGRAMMING IfApplicableSMS PROGRAMMING Continuedtion button. “PROP” and “CONTROL” shows on the SMS SPECIAL PROGRAM Review UsageMODE SMS PROGRAMMINGReset Usage MODE ContinuedFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemTech I/O Mode Appliance TestHeat Control MODE ContinuedSMS SPECIAL PROGRAM Continuedalong