Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny 680 KFC manual Gasket coming out of lid

Models: 680 KFC

1 109

Download 109 pages 54.87 Kb

Page 41

Gasket coming out of lid.

Gasket coming out of lid.

Steam leaking from around gasket.

Lid will not move up or down.

Lid will not stay down while latching.

Crumbs under gasket.

Gasket worn or damaged.

Gasket not sealing.

Cable broken.

Decorator strip interferring.

Magnet plate out of adjustment.

Remove and clean gasket. Clean rim of cookpot.

Replace gasket.

maintenance section on lid shims.

Replace cable.

Replace broken strip.

Adjust magnet plate in back of fryer.

Image 41

Henny Penny 680 KFC manual Gasket coming out of lid

Contents

Page Model 680 Gas Fryer SPECIFICATIONSHENNY PENNY 8 HEAD GAS PRESSURE FRYER Page Page Henny Penny LIMITED WARRANTY FOR HENNY PENNY APPLIANCESSection Page Section1-1.PRESSURE FRYER SECTION 1. INTRODUCTIONP-H-T PRESSUREThe word DANGER indicates an imminent hazard which will result in highly serious injury such as second or third degree burns, loss of sight, and other perma- nent injuries 10.Prepare the deadweight valve for operation 7.Load the Counterweight Assembly. See pageB . Remove the round weight 1.Cut and remove the metal bands from the cartonC.Remove and discard the shipping support D.Clean the orifice with a dry clothE.Replace the weight and secure the top cap MUST BE INSTALLED PER INSTRUCTIONS REMOVE REAR COVER WEIGHT SEGMENTSf-01REMOVE ACCESSORY BOXES FROM FRONT 05 ROLL UNIT OFF PALLET ONTO RAMPINSERT m EACH WEIGHT SEGMENT WEIGHS APPROXIMATELY~TH a SEGMENTPage To avoid possible serious personal injury Do not use cast iron fittings i CAUTION # ALL STR N Natural: 3.5 inches water column FILTER ONLY WHEN “COOL” IS DISPLAYED Power/Pump Gauge Solenoid Valve Drain Valve 3.Lift up on the lid handle until it stops To close lid4.Bring lid handle out towards you until it stops 5.Push lid handle down, locking lid in placeTo open lid INDICATORS 3-4.SWITCHES AND“Lo” Mode “Cool” Modeto “Drop” In the event of a power failure, no attempt should be made to operate the fryer. The Model 680 Fryer is equipped with an automatic ignition system and can not be operated without electrical power 1. Turn the main power switch to “OFF” Page Page To shutdown burner hj i’:.;,‘i ,e:::;.*f To isolate a malfunction, proceed as follows Product Color D. Spotted D. Rancid Taste Pressure will not Pressure does not build Shortening will not heat. “E20” Heating of shortening too slow or boil Gasket coming out of lid Removing 1. Remove electrical power supplied to the fryer 6.Straighten the capillary tube 1.Remove Control Panel 11.Turn power “ON” and check out fryer 1. Remove electrical power supplied to the fryer2.Drain the shortening from the cookpot 3.Remove the Control PanelPANEL - HENNY PENNY 5-7COMPLETE CONTROL5-8PRESSURE REGULATION Every 90 days1.Lower the lid assembly 3.Clean the gasket and gasket seat with hot water 4.Thread a 5116” nut on each end of the new cable 5-12.PRESSURE PAD 5-11.LID COUNTERWEIGHT CONT’DHenny Penny 5-13.LID ADJUSTMENTModel 1005Hertz 2.Remove the cover 5-16.SOLENOID VALVE Replacement Continued5-17.OPERATING CONTROL VALVECleaning Steps DO NOT MANUALLYACTIVATE THE SAFETY5-18.REMOVAL & CLEANING OF SAFETY VALVE5-19.PRESSURE GAUGE ContinuedCalibration Steps 5-18.REMOVAL & CLEANING1.Turn gas cock knob to the “OFF” position 9.Remove wires from control valve2.Pull gas cock knob from control valve 3.Remove cover from control valve12.Reassemble in reverse order 1.Remove both side panels 5. Replace with new transformer in reverse order 1. Remove electrical power supplied to the unit4.Remove the wires from transformer 2.Remove small access panel from right side panel 1. Remove electrical power supplied to the unit3.Pull hose from switch from under fryer 4.Disconnect wires from switch2.Remove small access panel from right side panel 1. Remove electrical power supplied to the unit3.Remove wires from modules 5.Install new module in reverse order1.Remove both side panels of unit 2.Using l/4” socket remove the left side panel 1.Remove electrical power supplied to the unitA.Both burners the same color, but not orangy-red 4.Mark the shield in the postion it is inLeft ‘Burner 6.Remove air hose gas valve 3.Locate wire nuts and disconnect leads Page 11.Secure the strips to the weights epyg-uinuebq plea ewy Page 2.Depress the “Select Time” button PROB - Temperature probe has failed 1.Enter the special program mode Product One FIGURE 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 35092 Page Not Avail e 1 L FIGURE Model Henny Penny6-12 1005FIGURE Page FIGURE Page FIGURE Page FIGURE Page FIGURE SMOOTH AND ROUNDED EDGE OF BLADE NOTE: ASSEMBLE CORE DISC ASSEMBLY WITHTOWARD DISC SPRING GUIDE ITEM NOTE: DO NOT DAMAGE SEAT IN ANY WAYFIGURE 8-HEADGAS COOKER J2OV, JPH, 2 WIRE W/GRr;iC&1 VACI511ti ‘” I I I I SIE. 72OV, If/-l,2 WIRE W/GRND8-HEADGAS COOKER PRESSURE 1l-Q?MODEL 680 GAS FRYER Y IAy--4A-<+-7N i I 1 \1 23 I6-27 Henny PennyModel 6-28 Henny PennyModel 6-29 Henny PennyModel 6-30 Henny PennyModel IfApplicable SMS PROGRAMMINGtion button. “PROP” and “CONTROL” shows on the SMS PROGRAMMINGContinued Review Usage SMS SPECIAL PROGRAMMODE SMS PROGRAMMINGMODE Continued Reset UsageFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemAppliance Test Tech I/O ModeHeat Control MODE Continuedalong SMS SPECIAL PROGRAMContinued