Page
SPECIFICATIONS
HENNY PENNY 8 HEAD GAS PRESSURE FRYER
Model 680 Gas Fryer
Page
Page
Henny Penny
LIMITED WARRANTY FOR HENNY PENNY APPLIANCES
Section
Page
Section
PRESSURE
SECTION 1. INTRODUCTION
1-1.PRESSURE FRYER
P-H-T
The word DANGER indicates an imminent hazard which will result in highly serious injury such as second or third degree burns, loss of sight, and other perma- nent injuries
1.Cut and remove the metal bands from the carton
7.Load the Counterweight Assembly. See page
10.Prepare the deadweight valve for operation
B . Remove the round weight
D.Clean the orifice with a dry cloth
E.Replace the weight and secure the top cap
C.Remove and discard the shipping support
05 ROLL UNIT OFF PALLET ONTO RAMP
REMOVE REAR COVER WEIGHT SEGMENTS
MUST BE INSTALLED PER INSTRUCTIONS
f-01REMOVE ACCESSORY BOXES FROM FRONT
SEGMENT
m EACH WEIGHT SEGMENT WEIGHS APPROXIMATELY
INSERT
~TH a
Page
To avoid possible serious personal injury
Do not use cast iron fittings
i CAUTION # ALL STR N
Natural: 3.5 inches water column
FILTER ONLY WHEN “COOL” IS DISPLAYED
Power/Pump
Gauge Solenoid Valve Drain Valve
5.Push lid handle down, locking lid in place
To close lid
3.Lift up on the lid handle until it stops
4.Bring lid handle out towards you until it stops
To open lid
“Cool” Mode
3-4.SWITCHES AND
INDICATORS
“Lo” Mode
to “Drop”
In the event of a power failure, no attempt should be made to operate the fryer. The Model 680 Fryer is equipped with an automatic ignition system and can not be operated without electrical power
1. Turn the main power switch to “OFF”
Page
Page
To shutdown burner
hj i’:.;,‘i ,e:::;.*f
To isolate a malfunction, proceed as follows
Product Color
D. Spotted
D. Rancid Taste
Pressure will not
Pressure does not build
Shortening will not heat. “E20”
Heating of shortening too slow
or boil
Gasket coming out of lid
Removing
1. Remove electrical power supplied to the fryer
6.Straighten the capillary tube
1.Remove Control Panel
3.Remove the Control Panel
1. Remove electrical power supplied to the fryer
11.Turn power “ON” and check out fryer
2.Drain the shortening from the cookpot
Every 90 days
5-7COMPLETE CONTROL
PANEL - HENNY PENNY
5-8PRESSURE REGULATION
1.Lower the lid assembly
3.Clean the gasket and gasket seat with hot water
4.Thread a 5116” nut on each end of the new cable
5-12.PRESSURE PAD
5-11.LID COUNTERWEIGHT CONT’D
1005
5-13.LID ADJUSTMENT
Henny Penny
Model
Hertz
2.Remove the cover
VALVE
Replacement Continued
5-16.SOLENOID VALVE
5-17.OPERATING CONTROL
OF SAFETY VALVE
DO NOT MANUALLYACTIVATE THE SAFETY
Cleaning Steps
5-18.REMOVAL & CLEANING
5-18.REMOVAL & CLEANING
Continued
5-19.PRESSURE GAUGE
Calibration Steps
3.Remove cover from control valve
9.Remove wires from control valve
1.Turn gas cock knob to the “OFF” position
2.Pull gas cock knob from control valve
12.Reassemble in reverse order
1.Remove both side panels
1. Remove electrical power supplied to the unit
4.Remove the wires from transformer
5. Replace with new transformer in reverse order
4.Disconnect wires from switch
1. Remove electrical power supplied to the unit
2.Remove small access panel from right side panel
3.Pull hose from switch from under fryer
5.Install new module in reverse order
1. Remove electrical power supplied to the unit
2.Remove small access panel from right side panel
3.Remove wires from modules
1.Remove both side panels of unit
4.Mark the shield in the postion it is in
1.Remove electrical power supplied to the unit
2.Using l/4” socket remove the left side panel
A.Both burners the same color, but not orangy-red
Left ‘Burner
6.Remove air hose
gas valve
3.Locate wire nuts and disconnect leads
Page
11.Secure the strips to the weights
epyg-uinuebq plea ewy
Page
2.Depress the “Select Time” button
PROB - Temperature probe has failed
1.Enter the special program mode
Product One
FIGURE
55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70
35092
Page
Not Avail
e 1 L
FIGURE
1005
Henny Penny
Model
6-12
FIGURE
Page
FIGURE
Page
FIGURE
Page
FIGURE
Page
FIGURE
NOTE: DO NOT DAMAGE SEAT IN ANY WAY
NOTE: ASSEMBLE CORE DISC ASSEMBLY WITH
SMOOTH AND ROUNDED EDGE OF BLADE
TOWARD DISC SPRING GUIDE ITEM
FIGURE
J2OV, JPH, 2 WIRE W/GRr;iC&
1 VACI511ti ‘”
8-HEADGAS COOKER
PRESSURE 1l-Q?
72OV, If/-l,2 WIRE W/GRND
I I I I SIE.
8-HEADGAS COOKER
23 I
Y IAy--4A-<+-7
MODEL 680 GAS FRYER
N i I 1 \1
Henny Penny
Model
6-27
Henny Penny
Model
6-28
Henny Penny
Model
6-29
Henny Penny
Model
6-30
IfApplicable
SMS PROGRAMMING
SMS PROGRAMMING
Continued
tion button. “PROP” and “CONTROL” shows on the
SMS PROGRAMMING
SMS SPECIAL PROGRAM
Review Usage
MODE
Speaker Frequency, Codes, Initialize System
Reset Usage
MODE Continued
Factory Presets F/C, Gas/Electric, Speaker Volume
MODE Continued
Tech I/O Mode
Appliance Test
Heat Control
SMS SPECIAL PROGRAM
Continued
along