Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny 680 KFC Insert, ~TH a, Segment, INSERT 4TH & 5TH SEGMENT INSERT 2ND & 3RD SEGMENT

Models: 680 KFC

1 109

Download 109 pages 54.87 Kb

Page 13

-INSERT

05 REMOVE 2 BOLTS MARKED “An TO RELEASE FRAME AFTER INSTALLING WEIGHT SEGMENTS.

-INSERT	~TH a
7TH	SEGMENT

INSERT 4TH &

5TH SEGMENT

INSERT 2ND &

3RD SEGMENT

INSERT IST

SEGMENT

WARNING!

m EACH WEIGHT SEGMENT WEIGHS APPROXIMATELY

18 LBS. (8.1 KG> - HANDLE WITH CARE.

m ALL SEGMENTS ARE IDENTICAL.

m ALL SEGMENTS MUST BE INSTALLED AND SECURED IN THE FRAME BEFORE ATTEMPTING TO UNLATCH LID.

Image 13

Henny Penny 680 KFC manual ~TH a, INSERT 4TH & 5TH SEGMENT INSERT 2ND & 3RD SEGMENT, Insert Ist Segment

Contents

Page HENNY PENNY 8 HEAD GAS PRESSURE FRYER SPECIFICATIONSModel 680 Gas Fryer Page Page Henny Penny LIMITED WARRANTY FOR HENNY PENNY APPLIANCESSection Page Section1-1.PRESSURE FRYER SECTION 1. INTRODUCTIONP-H-T PRESSUREThe word DANGER indicates an imminent hazard which will result in highly serious injury such as second or third degree burns, loss of sight, and other perma- nent injuries 10.Prepare the deadweight valve for operation 7.Load the Counterweight Assembly. See pageB . Remove the round weight 1.Cut and remove the metal bands from the cartonE.Replace the weight and secure the top cap D.Clean the orifice with a dry clothC.Remove and discard the shipping support MUST BE INSTALLED PER INSTRUCTIONS REMOVE REAR COVER WEIGHT SEGMENTSf-01REMOVE ACCESSORY BOXES FROM FRONT 05 ROLL UNIT OFF PALLET ONTO RAMPINSERT m EACH WEIGHT SEGMENT WEIGHS APPROXIMATELY~TH a SEGMENTPage To avoid possible serious personal injury Do not use cast iron fittings i CAUTION # ALL STR N Natural: 3.5 inches water column FILTER ONLY WHEN “COOL” IS DISPLAYED Power/Pump Gauge Solenoid Valve Drain Valve 3.Lift up on the lid handle until it stops To close lid4.Bring lid handle out towards you until it stops 5.Push lid handle down, locking lid in placeTo open lid INDICATORS 3-4.SWITCHES AND3-3.MELT CYCLE OPERATION “Lo” Modeto “Drop” In the event of a power failure, no attempt should be made to operate the fryer. The Model 680 Fryer is equipped with an automatic ignition system and can not be operated without electrical power 1. Turn the main power switch to “OFF” Page Page To shutdown burner hj i’:.;,‘i ,e:::;.*f To isolate a malfunction, proceed as follows Product Color D. Spotted D. Rancid Taste Pressure will not Pressure does not build Shortening will not heat. “E20” Heating of shortening too slow or boil Gasket coming out of lid Removing 1. Remove electrical power supplied to the fryer 6.Straighten the capillary tube 1.Remove Control Panel 11.Turn power “ON” and check out fryer 1. Remove electrical power supplied to the fryer2.Drain the shortening from the cookpot 3.Remove the Control PanelPANEL - HENNY PENNY 5-7COMPLETE CONTROL5-8PRESSURE REGULATION Every 90 days1.Lower the lid assembly 3.Clean the gasket and gasket seat with hot water 4.Thread a 5116” nut on each end of the new cable 5-12.PRESSURE PAD 5-11.LID COUNTERWEIGHT CONT’DHenny Penny 5-13.LID ADJUSTMENTModel 1005Hertz 2.Remove the cover 5-16.SOLENOID VALVE Replacement Continued5-17.OPERATING CONTROL VALVECleaning Steps DO NOT MANUALLYACTIVATE THE SAFETY5-18.REMOVAL & CLEANING OF SAFETY VALVE5-19.PRESSURE GAUGE ContinuedCalibration Steps 5-18.REMOVAL & CLEANING1.Turn gas cock knob to the “OFF” position 9.Remove wires from control valve2.Pull gas cock knob from control valve 3.Remove cover from control valve12.Reassemble in reverse order 1.Remove both side panels 4.Remove the wires from transformer 1. Remove electrical power supplied to the unit5. Replace with new transformer in reverse order 2.Remove small access panel from right side panel 1. Remove electrical power supplied to the unit3.Pull hose from switch from under fryer 4.Disconnect wires from switch2.Remove small access panel from right side panel 1. Remove electrical power supplied to the unit3.Remove wires from modules 5.Install new module in reverse order1.Remove both side panels of unit 2.Using l/4” socket remove the left side panel 1.Remove electrical power supplied to the unitA.Both burners the same color, but not orangy-red 4.Mark the shield in the postion it is inLeft ‘Burner 6.Remove air hose gas valve 3.Locate wire nuts and disconnect leads Page 11.Secure the strips to the weights epyg-uinuebq plea ewy Page 2.Depress the “Select Time” button PROB - Temperature probe has failed 1.Enter the special program mode Product One FIGURE 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 35092 Page Not Avail e 1 L FIGURE Model Henny Penny6-12 1005FIGURE Page FIGURE Page FIGURE Page FIGURE Page FIGURE SMOOTH AND ROUNDED EDGE OF BLADE NOTE: ASSEMBLE CORE DISC ASSEMBLY WITHTOWARD DISC SPRING GUIDE ITEM NOTE: DO NOT DAMAGE SEAT IN ANY WAYFIGURE 1 VACI511ti ‘” J2OV, JPH, 2 WIRE W/GRr;iC&8-HEADGAS COOKER I I I I SIE 72OV, If/-l,2 WIRE W/GRND8-HEADGAS COOKER PRESSURE 1l-Q?MODEL 680 GAS FRYER Y IAy--4A-<+-7N i I 1 \1 23 IModel Henny Penny6-27 Model Henny Penny6-28 Model Henny Penny6-29 Model Henny Penny6-30 IfApplicable SMS PROGRAMMINGContinued SMS PROGRAMMINGtion button. “PROP” and “CONTROL” shows on the Review Usage SMS SPECIAL PROGRAMMODE SMS PROGRAMMINGFactory Presets F/C, Gas/Electric, Speaker Volume Reset UsageMODE Continued Speaker Frequency, Codes, Initialize SystemAppliance Test Tech I/O ModeHeat Control SMS SPECIAL PROGRAMContinued SMS SPECIAL PROGRAMalong