Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny 680 KFC manual 35092

Models: 680 KFC

1 109

Download 109 pages 54.87 Kb

Page 80

35092

Henny PennyModel 680

FIGURE				UNITS
& ITEM		PART		PER
	NO.	NUMBER	DESCRIPTION	ASSY.

	80	35092	TOP FRAME BRACE	1
	81	SC01-160	SCREW, (1/4-20 X 1-1/4 HEX HD	4
	82	SC01-132	SCREW, (1/4-20 X 5/8" Soc. HD CAP SS)	8
	83	35725	ADAPTER, Hose Exhaust	1
√	84	35391	PANEL, RIGHT SIDE	1
√	85*	36210	REPLACEABLE BEEPER	1
√	85*	51877	WIRE/SPEAKER ASSY – SMS	1

√recommended parts *not shown

206

6-7

Image 80

Henny Penny 680 KFC manual 35092

Contents

Page Model 680 Gas Fryer SPECIFICATIONSHENNY PENNY 8 HEAD GAS PRESSURE FRYER Page Page LIMITED WARRANTY FOR HENNY PENNY APPLIANCES Henny PennySection Section PageSECTION 1. INTRODUCTION 1-1.PRESSURE FRYERP-H-T PRESSUREThe word DANGER indicates an imminent hazard which will result in highly serious injury such as second or third degree burns, loss of sight, and other perma- nent injuries 7.Load the Counterweight Assembly. See page 10.Prepare the deadweight valve for operationB . Remove the round weight 1.Cut and remove the metal bands from the cartonC.Remove and discard the shipping support D.Clean the orifice with a dry clothE.Replace the weight and secure the top cap REMOVE REAR COVER WEIGHT SEGMENTS MUST BE INSTALLED PER INSTRUCTIONSf-01REMOVE ACCESSORY BOXES FROM FRONT 05 ROLL UNIT OFF PALLET ONTO RAMPm EACH WEIGHT SEGMENT WEIGHS APPROXIMATELY INSERT~TH a SEGMENTPage To avoid possible serious personal injury Do not use cast iron fittings i CAUTION # ALL STR N Natural: 3.5 inches water column FILTER ONLY WHEN “COOL” IS DISPLAYED Power/Pump Gauge Solenoid Valve Drain Valve To close lid 3.Lift up on the lid handle until it stops4.Bring lid handle out towards you until it stops 5.Push lid handle down, locking lid in placeTo open lid 3-4.SWITCHES AND INDICATORS“Lo” Mode “Cool” Modeto “Drop” In the event of a power failure, no attempt should be made to operate the fryer. The Model 680 Fryer is equipped with an automatic ignition system and can not be operated without electrical power 1. Turn the main power switch to “OFF” Page Page To shutdown burner hj i’:.;,‘i ,e:::;.*f To isolate a malfunction, proceed as follows Product Color D. Spotted D. Rancid Taste Pressure will not Pressure does not build Shortening will not heat. “E20” Heating of shortening too slow or boil Gasket coming out of lid Removing 1. Remove electrical power supplied to the fryer 6.Straighten the capillary tube 1.Remove Control Panel 1. Remove electrical power supplied to the fryer 11.Turn power “ON” and check out fryer2.Drain the shortening from the cookpot 3.Remove the Control Panel5-7COMPLETE CONTROL PANEL - HENNY PENNY5-8PRESSURE REGULATION Every 90 days1.Lower the lid assembly 3.Clean the gasket and gasket seat with hot water 4.Thread a 5116” nut on each end of the new cable 5-11.LID COUNTERWEIGHT CONT’D 5-12.PRESSURE PAD5-13.LID ADJUSTMENT Henny PennyModel 1005Hertz 2.Remove the cover Replacement Continued 5-16.SOLENOID VALVE5-17.OPERATING CONTROL VALVEDO NOT MANUALLYACTIVATE THE SAFETY Cleaning Steps5-18.REMOVAL & CLEANING OF SAFETY VALVEContinued 5-19.PRESSURE GAUGECalibration Steps 5-18.REMOVAL & CLEANING9.Remove wires from control valve 1.Turn gas cock knob to the “OFF” position2.Pull gas cock knob from control valve 3.Remove cover from control valve12.Reassemble in reverse order 1.Remove both side panels 5. Replace with new transformer in reverse order 1. Remove electrical power supplied to the unit4.Remove the wires from transformer 1. Remove electrical power supplied to the unit 2.Remove small access panel from right side panel3.Pull hose from switch from under fryer 4.Disconnect wires from switch1. Remove electrical power supplied to the unit 2.Remove small access panel from right side panel3.Remove wires from modules 5.Install new module in reverse order1.Remove both side panels of unit 1.Remove electrical power supplied to the unit 2.Using l/4” socket remove the left side panelA.Both burners the same color, but not orangy-red 4.Mark the shield in the postion it is inLeft ‘Burner 6.Remove air hose gas valve 3.Locate wire nuts and disconnect leads Page 11.Secure the strips to the weights epyg-uinuebq plea ewy Page 2.Depress the “Select Time” button PROB - Temperature probe has failed 1.Enter the special program mode Product One FIGURE 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 35092 Page Not Avail e 1 L FIGURE Henny Penny Model6-12 1005FIGURE Page FIGURE Page FIGURE Page FIGURE Page FIGURE NOTE: ASSEMBLE CORE DISC ASSEMBLY WITH SMOOTH AND ROUNDED EDGE OF BLADETOWARD DISC SPRING GUIDE ITEM NOTE: DO NOT DAMAGE SEAT IN ANY WAYFIGURE 8-HEADGAS COOKER J2OV, JPH, 2 WIRE W/GRr;iC&1 VACI511ti ‘” 72OV, If/-l,2 WIRE W/GRND I I I I SIE.8-HEADGAS COOKER PRESSURE 1l-Q?Y IAy--4A-<+-7 MODEL 680 GAS FRYERN i I 1 \1 23 I6-27 Henny PennyModel 6-28 Henny PennyModel 6-29 Henny PennyModel 6-30 Henny PennyModel SMS PROGRAMMING IfApplicabletion button. “PROP” and “CONTROL” shows on the SMS PROGRAMMINGContinued SMS SPECIAL PROGRAM Review UsageMODE SMS PROGRAMMINGReset Usage MODE ContinuedFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemTech I/O Mode Appliance TestHeat Control MODE Continuedalong SMS SPECIAL PROGRAMContinued