Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny 680 KFC manual Heating of shortening too slow

Models: 680 KFC

1 109

Download 109 pages 54.87 Kb

Page 39

Heating of shortening too slow.

Heating of shortening too slow.

Shortening overheating.

Supply line too small - low gas volume.

Improper ventilation system.

Burner out of adjustment.

Programming wrong.

Faulty PC Board.

Faulty probe.

Increase supply line size. Refer to installation instructions.

Refer to installation instructions. Observe burners. Check gas pressure.

Adjust air flow so burners are an orangy-red.

Check temperature setting in the program mode.

Remove and replace control panel.

Remove and replace probe.

Image 39

Henny Penny 680 KFC manual Heating of shortening too slow

Contents

Page SPECIFICATIONS HENNY PENNY 8 HEAD GAS PRESSURE FRYERModel 680 Gas Fryer Page Page Henny Penny LIMITED WARRANTY FOR HENNY PENNY APPLIANCESSection Page SectionPRESSURE SECTION 1. INTRODUCTION1-1.PRESSURE FRYER P-H-TThe word DANGER indicates an imminent hazard which will result in highly serious injury such as second or third degree burns, loss of sight, and other perma- nent injuries 1.Cut and remove the metal bands from the carton 7.Load the Counterweight Assembly. See page10.Prepare the deadweight valve for operation B . Remove the round weightD.Clean the orifice with a dry cloth E.Replace the weight and secure the top capC.Remove and discard the shipping support 05 ROLL UNIT OFF PALLET ONTO RAMP REMOVE REAR COVER WEIGHT SEGMENTSMUST BE INSTALLED PER INSTRUCTIONS f-01REMOVE ACCESSORY BOXES FROM FRONTSEGMENT m EACH WEIGHT SEGMENT WEIGHS APPROXIMATELYINSERT ~TH aPage To avoid possible serious personal injury Do not use cast iron fittings i CAUTION # ALL STR N Natural: 3.5 inches water column FILTER ONLY WHEN “COOL” IS DISPLAYED Power/Pump Gauge Solenoid Valve Drain Valve 5.Push lid handle down, locking lid in place To close lid3.Lift up on the lid handle until it stops 4.Bring lid handle out towards you until it stopsTo open lid “Cool” Mode 3-4.SWITCHES ANDINDICATORS “Lo” Modeto “Drop” In the event of a power failure, no attempt should be made to operate the fryer. The Model 680 Fryer is equipped with an automatic ignition system and can not be operated without electrical power 1. Turn the main power switch to “OFF” Page Page To shutdown burner hj i’:.;,‘i ,e:::;.*f To isolate a malfunction, proceed as follows Product Color D. Spotted D. Rancid Taste Pressure will not Pressure does not build Shortening will not heat. “E20” Heating of shortening too slow or boil Gasket coming out of lid Removing 1. Remove electrical power supplied to the fryer 6.Straighten the capillary tube 1.Remove Control Panel 3.Remove the Control Panel 1. Remove electrical power supplied to the fryer11.Turn power “ON” and check out fryer 2.Drain the shortening from the cookpotEvery 90 days 5-7COMPLETE CONTROLPANEL - HENNY PENNY 5-8PRESSURE REGULATION1.Lower the lid assembly 3.Clean the gasket and gasket seat with hot water 4.Thread a 5116” nut on each end of the new cable 5-12.PRESSURE PAD 5-11.LID COUNTERWEIGHT CONT’D1005 5-13.LID ADJUSTMENTHenny Penny ModelHertz 2.Remove the cover VALVE Replacement Continued5-16.SOLENOID VALVE 5-17.OPERATING CONTROLOF SAFETY VALVE DO NOT MANUALLYACTIVATE THE SAFETYCleaning Steps 5-18.REMOVAL & CLEANING5-18.REMOVAL & CLEANING Continued5-19.PRESSURE GAUGE Calibration Steps3.Remove cover from control valve 9.Remove wires from control valve1.Turn gas cock knob to the “OFF” position 2.Pull gas cock knob from control valve12.Reassemble in reverse order 1.Remove both side panels 1. Remove electrical power supplied to the unit 4.Remove the wires from transformer5. Replace with new transformer in reverse order 4.Disconnect wires from switch 1. Remove electrical power supplied to the unit2.Remove small access panel from right side panel 3.Pull hose from switch from under fryer5.Install new module in reverse order 1. Remove electrical power supplied to the unit2.Remove small access panel from right side panel 3.Remove wires from modules1.Remove both side panels of unit 4.Mark the shield in the postion it is in 1.Remove electrical power supplied to the unit2.Using l/4” socket remove the left side panel A.Both burners the same color, but not orangy-redLeft ‘Burner 6.Remove air hose gas valve 3.Locate wire nuts and disconnect leads Page 11.Secure the strips to the weights epyg-uinuebq plea ewy Page 2.Depress the “Select Time” button PROB - Temperature probe has failed 1.Enter the special program mode Product One FIGURE 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 35092 Page Not Avail e 1 L FIGURE 1005 Henny PennyModel 6-12FIGURE Page FIGURE Page FIGURE Page FIGURE Page FIGURE NOTE: DO NOT DAMAGE SEAT IN ANY WAY NOTE: ASSEMBLE CORE DISC ASSEMBLY WITHSMOOTH AND ROUNDED EDGE OF BLADE TOWARD DISC SPRING GUIDE ITEMFIGURE J2OV, JPH, 2 WIRE W/GRr;iC& 1 VACI511ti ‘”8-HEADGAS COOKER PRESSURE 1l-Q? 72OV, If/-l,2 WIRE W/GRNDI I I I SIE. 8-HEADGAS COOKER23 I Y IAy--4A-<+-7MODEL 680 GAS FRYER N i I 1 \1Henny Penny Model6-27 Henny Penny Model6-28 Henny Penny Model6-29 Henny Penny Model6-30 IfApplicable SMS PROGRAMMINGSMS PROGRAMMING Continuedtion button. “PROP” and “CONTROL” shows on the SMS PROGRAMMING SMS SPECIAL PROGRAMReview Usage MODESpeaker Frequency, Codes, Initialize System Reset UsageMODE Continued Factory Presets F/C, Gas/Electric, Speaker VolumeMODE Continued Tech I/O ModeAppliance Test Heat ControlSMS SPECIAL PROGRAM Continuedalong