Integra DHC-9.9 instruction manual Tuner, Analog Multich, Hdmi, Advanced Setup—Continued, Notes

Advanced Setup—Continued

Tuner

■AM Freq Step (on some models)

See “AM Frequency Step Setup (on some models)” on page 57.

■Satellite Radio (on North American model)

If you connect an XM Satellite Radio antenna or SIRIUS Satellite Radio antenna to the AV controller (both sold separately), set this setting to XM or SIRIUS respec- tively. If you connect both types of antenna, select XM/SIRIUS. Otherwise, select None (see pages 74–88).

Analog Multich

■Subwoofer Input Sensitivity

Some DVD players output the LFE channel from their analog subwoofer output at 15 dB higher than normal. With this setting, you can change the AV controller’s subwoofer sensitivity to match your DVD player. Note that this setting only affects signals connected to the AV controller’s MULTI CH: SUBWOOFER jack.

You can select 0 dB, 5 dB, 10 dB, or 15 dB.

If you find that your subwoofer is too loud, try the 10 dB or 15 dB setting.

HDMI

■Audio TV Out

This setting determines whether audio received by an HDMI input is output by the HDMI outputs. You may want to change this setting to “On” if your TV is con- nected to an HDMI output and you want to listen to audio from an HDMI component through your TV’s speakers. Normally, it should be set to “Off”.

Off: HDMI audio is not output (default).

On: HDMI audio is output.

Notes:

•If “On” is selected and the signal can be output by the TV, the AV controller will output no sound through its speakers.

•When “TV Control” is enabled, this setting is set to “Auto”.

•With some TVs and input signals, no sound may be output even if “On” is selected.

•When the “Audio TV Out” setting is set to “On”, or “TV Control” is set to “Enable” and you’re listening through your TV’s speakers (see page 38), if you turn up the AV controller’s volume control, the sound will be output by the AV controller’s speakers. To stop the AV controller’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV controller’s volume.

■Lip Sync

The Lip Sync function can automatically synchronize HDMI audio and video that’s gotten out of sync due to the complex digital video processing being performed by your HDMI-compatible TV. With HDMI Lip Sync, the audio delay required to synchronize the audio and video is calculated and applied automatically by the AV con- troller.

Disable: HDMI lip sync disabled (default).

Enable: HDMI lip sync enabled.

Notes:

•This function works only if your HDMI-compatible TV supports HDMI Lip Sync.

•You can check the amount of delay being applied by the HDMI Lip Sync function on the “A/V Sync” screen (see page 118).

■x.v.Color

If your HDMI source and HDMI-compatible TV both support the “x.v.Color”, you can enable “x.v.Color” on the AV controller with this setting.

Disable: “x.v.Color” disabled (default).

Enable: “x.v.Color” enabled.

Notes:

•If the color is unnatural when “x.v.Color” is set to “Enable”, change the setting to “Disable”.

•Refer to the connected component’s instruction man- ual for details.

■Control

This function allows -compatible components connected via HDMI to be controlled with the AV con- troller.

Disable: disabled (default).

Enable: enabled.

Notes:

• , which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo components. The AV controller can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with

components other than -compatible compo- nents cannot be guaranteed.

•Set to “Disable” when a connected piece of equipment is not compatible or it is unclear whether the equip- ment is compatible or not.

•If movement is unnatural when set to “Enable”, change the setting to “Disable”.

•Refer to the connected component’s instruction man- ual for details.

126