Mitsubishi Electronics LT-3280, LT-3780 manual Troubleshooting and Support

Chapter 7: Troubleshooting and Support

Problem Possible Solution

24.

The TV Audio icon or A/V Receiver icon is grayed out and not selectable.

•Select the Change setting from the Edit NetCommand menu, and then select the device (for example VCR). Once the Connection screen is displayed, check if the audio checkbox is selected for the TV input and/or AVR input.

•Verify the connections and NetCommand setup for the A/V receiver and the desired source device, if any. See the instructions for item 23, previous page.

25.	Devices are grayed out in the Device Selection	• A recording is in progress requiring the use of Monitor Out. Cancel
	menu or the PIP Selection menu.	the recording to select the device.
		• Digital channels and media cards cannot display in the PIP or POP.
26.	Cannot see the A/V Receiver menu.	• The A/V Receiver is not connected to any input of the media center.
		To check the A/V Receiver menu temporarily plug into an unused
		input of the media center. Then select Review from the NetCommand
		Menu, turn the input On to view the A/V Receiver menu.
27.	Screen is black when trying to view digital	• The PerfectColor™ color balance has been incorrectly set. Use the
	channels or IEEE 1394 device.	Setup menu to reset the color balance.
28.	The REC button is not working, or, on the	• The device does not support recording, such as a DVD player.
	Transport menu the record key is grayed out and	• Recordings can not be initiated from the Transport menu when
	not available.	using an IEEE 1394 device. Press REC instead. The Record
		menu displays allowing setup of a recording.
29.	Excessive digital artifacts.	• The IEEE 1394 cable is too long (15 feet between devices is the
		maximum length).
		• There may be a slow device in the middle of the IEEE 1394 network.
		Move the slow devices to the end so that connections for faster
		devices do not pass through them.
30.	DVCR analog/digital problems.	• If the tape is currently playing but no picture displays, there may be a
		mismatch of the media with the display. Press DEVICE to
		display the Device Selection menu. Press ENTER for the DVCR
		device. If digital is selected, try analog, or if analog is selected, try
		digital.
31.	D-VHS recordings for digital cable have drop-	• Digital cable signals on IEEE 1394 can exceed the data rate
	outs (loss of picture or sound), or no playback.	standards supported by DVCR.
32.	There is no audio and video from the IEEE 1394	• The device is not turned on - turn the device power on.
	device.	• No media (tape or disc) is inserted into the device.
		• The media is blank (has no recording).
		• The play command failed - Try pressing play again on the device’s
		remote control or front panel.
		• The device is already in use (for example: the device is currently
		recording).
		• The source is copy-protected or violates copy protection.
		• The device’s digital video signal is not supported by the TV, such as
		DV video, common with camcorders. Use analog connections
		instead, if available.
		• The device is not an audio/video device.
		• Too many other devices are already communicating over IEEE 1394.
		Remove or stop some devices and try again.
33.	The IEEE 1394 Device is not listed in the Device	• The device is unchecked in the Review screen. Select the
	Selection menu.	NetCommand menu. Through Review, verify the device is checked.
		• The IEEE 1394 plug is disconnected or loose.
		• The IEEE 1394 Device has not been powered On. Turn on.
		• The device has not been discovered.
		• The device is not an Audio/Video device.
34.	The IEEE 1394 device cannot be selected.	• The device may be busy, either recording or a peer-to-peer
		connection has been established. Cancel the recording or
		peer-to-peer connection.
35.	DEVICE MENU button does not display a menu.	• The IEEE 1394 device does not provide a menu.
		• The TV cannot support IEEE 1394 menus. See page 32.

90