Omega RD260A Chapter 7 SET UP MODE

7 - 1

7. SET UP MODE

Chapter 7 SET UP MODE

This chapter describes the Set Up Mode.

7.1 Setting the Output Relay to Energize/De-energize Upon Alarm (option)

7.2 Setting Alarm Hysteresis On/Off

7.3 Setting the A/D Integration Time (Pen model)

7.4 Setting Upscale/Downscale TC Burnout

7.5 Configuring the Input Filter (Pen Model)

7.6 Setting for Moving Average Calculations (Dot-printing model)

7.7 Turning Offset Settings Protection On/Off

7.8 Assigning Different Colors to Channels (Dot-printing model)

7.9 Setting Pen Offset Compensation On/Off (Pen model, /D1 option)

7.10Turning Alarm Printing On/Off

7.11Setting Periodic Printout On/Off

7.12Turning Printing of Changes in Chart Speed On/Off

7.13Turning Printing of Channel Numbers On/Off (Dot-printing model)

7.14Selecting channel Number or Tag

7.15Changing the Temperature Unit (/D2 option)

7.16Changing Default Settings for REMOTE Operation (option)

7.17Turning the Setting Protection Function On/Off

7.18Initializing Settings

Contents

Main Servicing North America: USA: Canada: For immediate technical or application assistance: USA and Canada: INTRODUCTION NOTE WARNING SAFETY PRECAUTIONS Page HOW TO USE THIS MANUAL CONTENTS Page Chapter 1 BEFORE INSTALLATION 1.1 Handling Precautions 1 - 2 1.2 Checking and Unpacking 1.2.1 Checking Accessories and Appearance CAUTION 1.2.2 Removing Packings Page Chapter 2 INSTALLATION 2.1 Installation Site and Mounting Methods 2.1.1 Installation Site 2.1.2 Mounting Methods 2.1.3 External Dimensions NOTE 2.2 Wiring 2.2.1 Rear Panel Terminal Arrangement 2.2.2 Power Supply Wiring NOTE 2.2.3 Input Signal Wiring NOTE 2 - 7 2.2.4 Alarm Output Wiring (option) WARNING NOTE 2.2.5 Remote Control Wiring (option) NOTE Page 3.1 Front Panel Page 3.2 Characters on the Display Chapter 4 DAILY OPERATION/ MAINTENANCE 4.1 Switching Power On/Off NOTE 4.2 Installing (or Replacing) Chart Paper NOTE 4.3 Installing (or Replacing) Pens (Pen model) NOTE Page CAUTION 4.4 Installing (or Replacing) Ribbon Cassette (Dot-printing model) 4 - 7 4. DAILY OPERATION/MAINTENANCE 4.5 Getting the Recording 4.5 Getting the Recording 4.5.1 Starting/Stoping the Recording Press the [RCD] key to start or stop the recording. 4.5.2 Feeding the Chart The chart paper is fed by pressing the [FEED] key as long as the key is pressed. 4.6 Getting a Digital Printout 4.6.1 Getting a List Printout NOTE 4.6.2 Getting a SET UP List Printout NOTE 4.7 Selectting the Display 4.8 Maintenance 4.8.1 Periodic Maintenance 4.8.2 Battery Replacement 4.8.3 Fuse Replacement 4.8.4 Cleaning the Carriage Shafts ! WARNING 4.8.5 Calibration CAUTION NOTE 4 - 15 4. DAILY OPERATION/MAINTENANCE 4.8 Maintenance Temperature Compensation for Thermocouple Signal 4.8.6 Pen-Position Adjustment (Pen model) NOTE Page 4.8.7 Dot-Position Adjustment (Dot-printing model) NOTE Page Chapter 5 DATA SETTING GUIDES 5.1 Various Modes NOTE 5.1.1 OPERATION Mode 5 - 4 5.1.2 SET Mode This flow can be entered by pressing the [DISP] key for three seconds. 5.1.3 SET UP Mode 5 - 6 5.2 Procedures to Enter Setting Data NOTE Chapter 6 SET MODE 6.1 Setting Input Range and Recording Span (RANGE) NOTE SKIP Setting Voltage Measurement Setting (VOLT Setting) Thermocouple and Resistance Temperature Detector Setting (TC, RTD Setting) Digital Input Setting (DI Setting) NOTE Difference Computation Setting (DELT Setting) Scale Setting (SCL Setting) NOTE Setting to Obtain Square Root (SQRT Setting) F = (V V ) + F 10 (F F ) V V 6.2 Setting Offsets (OFFST) 6.3 Setting Alarms (ALARM) NOTE 6 - 14 6.4 Assigning Units (UNIT) S/P means SPACE. NOTE indication returns to the [ ] and already set data will be aborted. 6.5 Setting Chart Speed (CHART) NOTE 6.6 Setting Date/Time (CLOCK) 6.7 Adjusting the Trend Recording Format (TREND, Dot-printing model) 6 - 18 6.8 Assigning Tags (TAG) S/P means SPACE. 6.9 Setting Messages (MSG) NOTE 6.10 Setting Key-lock (KEY) Chapter 7 SET UP MODE 7.1 Setting the Output Relay to Energize/De-energize Upon Alarm (option) 7.2 Setting Alarm Hysteresis On/Off NOTE 7.3 Setting A/D Integration Time (Pen model) 7.4 Setting Upscale/Downscale TC Burnout 7.5 Configuring the Input Filter (Pen Model) 7.6 Setting for Moving Average Calculations (Dot-printing model) 7.7 Turning Offset Settings Protection On/Off NOTE 7.8 Assigning Different Colors to Channels (Dot-printing model) 7.9 Setting Pen Offset Compensation On/Off (Pen model, /D1 option) NOTE 7.10 Turning Alarm Printing On/Off 7.11 Setting Periodic Printout On/Off NOTE 7.12 Turning Printing of Changes in Chart Speed On/Off 7.13 Turning Printing of Channel Numbers On/Off (Dot-printing model) 7.14 Selecting channel Number or Tag NOTE 7.15 Changing the Temperature Unit (/D2 option) NOTE 7.16 Changing Default Settings for REMOTE Operation (option) NOTE 7.17 Turning the Settings Protection Function On/Off NOTE 7.18 Initializing Settings 8 - 1 8.1 Error Code List Chapter 8 TROUBLESHOOTING 8.1 Error Code List 8 - 2 8 - 3 8.2 Troubleshooting 8.2 Troubleshooting 8 - 4 8 - 5 WARRANT Y/DISCLAIMER RETURN REQUEST S / INQUIRIES M3289/0299 W h e r e Do I Find Everything I Need for P r ocess Measurement and Control? OMEGAOf Course! T E M P E R AT U R E PRESSURE, STRAIN AND FORCE F L O W / L E V E L p H / C O N D U C T I V I T Y