Mail Send Function Errors | Omron CJ1W-ETN21 specification

Mail Send Function Errors

Section 2-8

■Access Times for CS1 and CJ1 CPU Units

Command	Data size	CPU Unit's operating mode

		PROGRAM	RUN

		---	10 ms cycle time

IOM data	1 word	0.1 s	0.1 s

	6,000 words	0.3 s	0.3 s

File data	1 KB	0.3 s	1.1 s

	10 KB	1.3 s	7.3 s

	100 KB	10.6 s	72.2 s

	1 MB	137.4 s	1,139.5 s

■Access Times for CS1-H and CJ1-H CPU Units

	Command	Data size	CPU Unit's operating mode

			PROGRAM	RUN

			---	10 ms cycle time

	IOM data	1 word	0.1 s	0.1 s
	(words)
	(words)	6,000 words	0.3 s	0.2 s
		6,000 words	0.3 s	0.2 s

	File data	1 KB	0.1 s	0.3 s
	(bytes)
	(bytes)	10 KB	0.6 s	2.0 s
		10 KB	0.6 s	2.0 s

		100 KB	5.0 s	18.3 s

		1 MB	49.4 s	272.8 s

Note (1) The access times for file data indicate Memory Card access times.

(2)The access times in the table above are standard times when the PLC Setup's “Fixed Peripheral Servicing Time” setting is set to the default val- ue of 4% of the cycle time.

(3)The attached file transfer time can be reduced by increasing the time al- lowed for peripheral servicing in the PLC Setup's “Fixed Peripheral Ser- vicing Time” setting.

2-8 Mail Send Function Errors

2-8-1 Identifying and Correcting Mail Send Function Errors

The following table shows the primary causes of e-mail transmission errors and corresponding solution.

Cause	Correction

The SMTP (DNS or POP) server address	Correctly set each server address (IP
has not been set.	address or host name).

POP before SMTP authentication error	Correctly set the POP settings (account
	and password).

SMTP (DNS or POP) server communica-	Inspect the communications path (Ether-
tions timeout	net Unit, cable connections, hub, router,
	and server) and correct any problems or
	damage.

Local mail address has not been set.	Correctly set the local mail address.

Destination mail address has not been	Correctly set the destination mail
set.	address.

The trigger is set and the user-set data,	Correctly set the data to be sent.
error log, status, and file data/I/O data
settings are all zero.

Trigger type setting error	Correctly set the trigger type setting.

28

Image 52

Omron CJ1W-ETN21 Identifying and Correcting Mail Send Function Errors, Access Times for CS1 and CJ1 CPU Units

Contents

Ethernet Units Construction of Applications Revised November Omron Product References  OmronPage Table of Contents FTP Server Index 207 Revision History 215 Table of Contents Information on setting communications using CX-Programmer Information on how to manage and use IP addressesCommands Section Contents Manual Model Name Contents Number Relevant Manuals Xiii Xiv Read and Understand this Manual Application Considerations Disclaimers Xviii Notation of Unit Versions on Products Unit VersionsConfirming Unit Versions with Support Software Unit Version Notation Lowing table Precautions Safety Precautions General PrecautionsIntended Audience Safety Precautions Operating Environment Precautions Application Precautions Application Precautions Conformance to EC Directives Applicable DirectivesConcepts EMC Directives Section Ethernet Unit Communications Services Service Main functions Counterpart device ReferenceFunctions Listed by Purpose Acquired for the Ethernet Unit Communications Protocol used Situation when used Reference Unit setting tagTable of Protocols Section Contents Default Common Protocol SettingsSmtp 2 POP 3 DNS Section Section Mail Send Function Mail Send Function Overview IntroductionAdvantages Description Comparison with the Earlier Mail Send Function Mail Send Function DetailsMail Send Functions Compatibility with Earlier Models Contents of E-mail Body Following header information is included Trigger condition Text entered as subject Words value has changed Channel data has changed from XX to Ethernet Unit InformationEthernet Unit information is always included in the e-mail Optional Information Error Log Information Status Information Extension ContentAttached File Details Memory Data 6,000 Words Max File Data 1 MB Max Summary of E-mail Body Information and Attached FilesData sent Body/Attached file Mail body Function Specifications Mail Send Function SpecificationsSpecifications Using the Mail Send Function ProcedureDetails of the Available Mail Triggers Classification Trigger type Settings Required for the Mail Send Function Transferring the settings dataSetting Setting requirement Reference Unit Setup Using the Mail Send Function Mail Address Set up to 2 destination mail addressesSend Mail Send Mail Condition Settings Mail Address Specification RequiredData Sent by Mail When Required Data Sent in E-mail Body Data Sent in an Attached File Send Mail Trigger Type Setting Required Attached File Name Send Mail Status Mail Send Function StatusSend Mail Status Mail Send Switch Bit 03 of n Mail Send Switch, Accessing Memory/Sending Mail FlagBit numbers Status Accessing Memory/Sending Mail Flag Bit 01 of n+17 Memory Data FormatsIOM Format TXT Format Attached File Transfer Times CSV Format Mail Send Function Errors Identifying and Correcting Mail Send Function ErrorsAccess Times for CS1 and CJ1 CPU Units Access Times for CS1-H and CJ1-H CPU Units Troubleshooting Mail Send Errors with LED Indicators Error Log Error Codes for the Mail Send FunctionError Meaning Detailed error code Correction Probable cause Correction Make the Unit Setup Settings from the CX-Programmer Initial Settings ExampleInitial Server Settings Example Application Destination Mail Address Setup Send Condition Setting Transfer the CPU Bus Unit Setup Settings Automatic Transmission when Send Condition is SatisfiedExample Send e-mail when W300 bit 00 goes from OFF to on Send when there is a Change in the CPU Units Status Receive Mail Function Configuration of the Mail Mail Receive Function OverviewAdvantages Description Table of Remote Mail Commands Command ParametersCommand Execution Results Attached File Data Specification Mail Receive Function SpecificationsReceived E-mail Response E-mail Using the Mail Receive Function Settings Required for the Mail Receive Function Tion Posting Mail Address Protection Setting Receive Mail Tab Receive Attached File Setting Receive Command Setting Remote Mail Command Details Command FormatFormat Response Format Command Format FileWrite File WriteFunction Mounted in the CPU Unit FileRead File Read FileDelete File Delete Card mounted in the CPU Unit EM file memory or a Memory Card mounted in the CPU Unit FileList File List ReadResponse Format Details Command Format Details UMBackup User Memory BackupMemory or a Memory Card mounted in the CPU Unit PARAMBackup Parameter Area Backup Or a Memory Card mounted in the CPU Unit IOMWrite I/O Memory Write Units I/O memory. The data is written in word units Subject Body IOMRead I/O Memory Read Units ReIOMRead ChangeMode Operating Mode Change Changes the CPU Units operating mode ErrorLogRead Error Log Read Bus Unit or Special I/O Unit ErrorLogClear Error Log Clear Since power was turned on or the mail log was cleared MailLogRead Mail Log Read MailLogClear Mail Log Clear Net Unit Test Mail Test Response List FinsSend Fins Command SendResponse Response Status Description Code Accessing Memory/Receiving Mail Flag Accessing Memory/ Receiving Mail Flag Bit 02 of n+17Mail Receive Function Status IOM Format TXT Format CSV Format Access Times for CS1 CJ1 CPU Units Access Times for CS1-H CJ1-H CPU Units Identifying and Correcting Mail Receive Function Errors Mail Receive Function ErrorsTroubleshooting Mail Receive Errors with LED Indicators Error code Meaning Detailed error code Correction Hex 1st byte 2nd byte Initial Settings for the Mail Receive Function DNS Server IP Address Setting DNS Tab, When RequiredItem name Example Reading Data from a CPU Unit Data Area Send Remote Mail CommandsBacking Up the CPU Units User Program Memory Card FTP Server Specifications Overview FTP Server Function Details Connecting to the FTP ServerFile Types Using the FTP Server Function FTP File Transfer Mode List of Settings Required for the FTP Server Function Setup TabCX-Programmer Settings Setting conditions Tab Setting Details Default value FTP Server Application Example Confidential Using FTP Commands Table of CommandsUsing the Commands Open Dir UserRename Mkdir RmdirPwd Cdup Type GetMget Put Delete MdeleteClose Bye Error Messages Error Messages and FTP StatusMessage Meaning FTP Indicator FTP indicator MeaningChecking FTP Status FTP Status Flag Using File Memory File MemoryFile Names Directories File Names Handled by CPU Unit File type File name Extension Contents DescriptionUnit Initializing File Memory 4 I/O Memory Data FormatMemory Initialization method Data format Use of CRs and CR position Section 9ABC FTP File Transfer Time CS1 CPU Units/CJ1 CPU UnitsCS1-H CPU Units/CJ1-H CPU Units File system Memory Card EM File Memory Enter the login name Unix Application Example Change to the Memcard directory Change data type to binaryTransfer the file RESULT.IOM to the workstation Write the file PLAN.IOM to the Memory Card Section Automatic Clock Adjustment Function Overview CPU Unit Conditions Using the Automatic Clock Adjustment Function Settings Required for Automatic Clock Adjustment Function Settings Setting conditions Reference Auto Adjust Time Automatic Clock Adjustment Switch Automatic Clock Adjustment Error ProcessingAutomatic Clock Adjustment Sntp Errors Automatic Clock Adjustment Switch Bit 04 of n Automatic Clock Adjustment Error Processing CPU Unit error Socket Services Page Using Sockets with the Ethernet Unit Overview of Socket Communications from Ethernet UnitsWhat are Sockets? Socket Port Numbers Protocol Overview Differences between TCP and UDPOpening TCP Sockets TCP Communications TCP Communications Procedure Passive Open and Active Open Fragmentation of Send Data Socket Service Functions Using Socket Services with Socket Service Request Switches Protocol Socket Service Request CMND490 Using Socket Services with CMND490 Specific Socket Service FunctionsCommand code Name Protocol Socket service request Socket Service Function Guide Differences with Previous ModelsManipulating Dedicated Control Bits Executing CMND490 Using Socket Service Functions Settings Required for Socket Service FunctionCX-Programmer Setting Setting requirements Unit Setup Tab Manipulating Dedicated Control Bits Setup Details Default value 109 CIO Area Allocations Socket Service StatusUDP/TCP Socket Status Ethernet Unit to CPU Unit Bit Switch Status Manipulated Unit operation DM Area Allocations Application Procedure ProcedureTCP Connection Status Ethernet Unit to CPU Unit Number Status Meaning Socket Services and Socket Status Precautions Error Evaluation Program Flow Socket Service Parameters Parameter Settings Use of the parameters by the socket serviceUDP Socket Services TCP Socket Services Parameters Socket OptionUDP/TCP Socket No Local UDP/TCP Port No Following specifications can be used Remote UDP/TCP Port NoTime Out Time Number of Bytes to Send/Receive Socket Service Request Switches Following diagram Response Codes UDP Socket Open RequestUDP Socket Receive Request Response Meaning Code UDP Socket Send Request UDP Socket Close Request TCP Socket Passive Open Request TCP Socket Active Open Request TCP Socket Receive Request Drinuse TCP Socket Send Request Timing Charts TCP Socket Close RequestClosing during Other Processes Close Request Switch Force-close Switch System Configuration 8 TCP/IP Communications Programming ExampleData Flow Basic Operations DM Area Program Memory MapCIO Area Programming Example TCP Passive Open 130 Programming example uses the following system configuration 9 UDP/IP Communications Programming Example Tion on errors CIO 000000 is turned on to request opening a UDP socket from 133 134 135 Using Socket Services with CMND490 Using Socket Service 137 Basic Fins Command Format Command CodeSocket Number Results Storage Area Response Codes in the Command Response Communications Timing ChartSocket Service Timing Chart Response Codes in the Results Storage Areas 140 System Configuration Close Request during Receive Request Data Flow Basic Operations Program Memory Maps Are structured 144 145 146 147 148 149 150 151 152 153 154 Precautions in Using Socket Services UDP and TCP Socket ServicesUDP Socket Service TCP Socket Service Precautions in Using Socket Service Request Switches TCP Socket Services Using CMND490 CS/CJ CPU Units Maximum Transmission Delays Ignoring other Network DelaysCS-H/CJ-H CPU Units Calculation Using Fins Communications to Create Host Applications Overview of Fins Communications Communications On an Ethernet Network Using the FINS/UDP and FINS/TCP Methods Fins Communications Service Specifications for Ethernet Fins Command Frame Format Fins FramesFins Response Frame Format Fins Header Information FINS/UDP Features FINS/UDP Method FINS/UDP Frame Format UDP Port Numbers for FINS/UDP Procedure for Using Designating Remote Addresses Sending Commands from a Host ComputerCommunications Parameters Used by Host Computer By sending a Fins command Memory Area READ, command code Mand, the command will be resentFINS/UDP Sample Program Operation Overview Sample Program 15 * FINS/UDP Communications Sample Program 169 170 FINS/TCP Features FINS/TCP Method TCP Port Number for FINS/TCP Frame FormatFINS/TCP Connection Numbers FINS/TCP Connection Status Word n+23 CommunicationsAge them in an internal table Automatic Allocation Procedure Automatic Allocation Fins Node Addresses 175 Setup Tab FINS/TCP Tab FINS/TCP Mode Specifications Fins Node Address Data Send Client to Server CommandFins Node Address Data Send Server to Client Command FINS/TCP Headers Following table shows the list of error codes Fins Frame Send CommandError code Details Hexadecimal Fins Frame Send Error Notification Command Command Connection Sequence Normal Operation Error Connection Sequence ACK FIN 182 183 From onwards, the connection is established again Host computer Remote node FINS/TCP Sample Program 186 187 188 189 190 191 Maximum Transmission Delays Writing/Reading to CPU Unit Write Command Delay TimeTransmission Delay Receive Processing Command CPU Bus Unit Service Cycle Read Command Delay Time Transmission Processing704 ms Response 194 Ethernet Network Parameters Parameter Value Description Appendix a Buffer Configuration Appendix B Network Memory TCP Status Transitions Status Meaning Appendix C Ascii Characters Space Appendix D Maintenance Settings after Replacing an Ethernet UnitSettings After Replacing a CPU Replacing an Ethernet Unit Appendix E Items InspectionsTools Required for Inspection Appendix F Numerics Index 209 210 211 212 213 214 Revision code Date Revised content Revision History Revision History Omron Corporation Control Devices Division H.Q Regional Headquarters Authorized Distributor