Panasonic AJ-HD1700PE Audio channel selector button, Number keys, PREVIEW/REVIEW button

Parts and Their Functions

Front panel

LN

EJECT

XL/L/M

- cassette

POWER

OFF

ON

Do not insert S-cassette

without adapter

CH

1

2

3

4

5

6

7

8

CUE

CH CONDITION

MONITOR

FULL/FINE

REMOTE

9P

50P

RS-232C

L

R

HEADPHONES

HOME

RF1

RF2ASSEM

ADJUST

SHTL

JOG

VAR

PUSH-INTER

VIDEO

UNITY

TC

CUE

INSERT

REV

FWD

AUDIO

UNITY

DIAG

MENU

STAND BY

PLAYER

RECORDER

INPUT CHECK

SHIFT

F1

F2

F3

F4

F5

F6

SERVO

REC INHIBIT

AUDIO CH SELECT

A IN

A OUT

EDIT

PLAY

ABC

DEF

GHI

REC

CH

1

CH

5 CH 2

CH

6 CH 3

CH

7 CH

4

CH 8

7

8

9

PREVIEW/

PRE-

JKL

MNO

PQRS

REVIEW

ROLL

4

5

6

BS

AUTO

TUV

WXYZ

TRIM

REW

STOP

FF

1

2

3

ENT

EDIT

SET

PUSH

IN

OUT

LOCK

0

C

T

F

FULL

REC

P8

REC

P8

REC

P8

REC

P8

FULL

J K M O

JAudio channel selector button

Use this button to select whether the audio controls for channels CH1 to CH4 or for channels CH5 to CH8 are to be controlled.

Each time it is pressed, the channel display LED above the audio control is selected.

KNumber keys

Use these keys to input the numerical values of the

CUE points, edit points, etc.
By pressing a number keys from	to	while the1	9

Fkey is held down, alphabet letters from A to F which are used for the user’s bit or letters from A to Z which are used to compose filenames can be input.

Since a multiple number of letters are allocated to each number key, keep tapping the number key until the desired letter is selected. To change the input position, use the ADJUST dial, and then proceed with the input.

LPREVIEW/REVIEW button

PREVIEW: When the button is pressed after an edit point has been registered, the tape travels and the editing can be previewed without actually performing the editing.

If the button is pressed when the IN point has not been registered, the point where it was pressed is registered as the IN point, and preview is executed using this IN point.

REVIEW: When the button is pressed after a section has been edited, the just edited section is played back, and it can be reviewed on the recorder’s monitor.

MAUTO EDIT button

When this button is pressed after the edit points have been registered, automatic editing is initiated. If the button is pressed when the IN point has not been registered, automatic editing is initiated with the point where the button was pressed serving as

the IN point.

NPREROLL button

This button is used to locate where a transmission or manual editing starts on the tape.

When it is pressed, the tape travels to the preroll point and it stops there.

When the cue time has been registered on the HOME, PF1 or PF2 screen:

The tape is prerolled from the registered cue time
using the preroll time which was set using					.
						F1
(PREROL) on the <HOME SHIFT> menu.
When the search mode is established on the
CUE screen:
The tape is prerolled from the selected cue point
using the preroll			time which was set using
						F5
(CU-ROL) on the <CUE SHIFT> menu.
The preroll operation is not performed when the
selected cue		point	has not been registered or
when	the	cue	point registration mode		is
established.
In all other situations:
The tape is prerolled from the registered IN point
(or the current tape position when the IN point has
not been registered) using the preroll time which
was	set using			(PREROL) on	the <HOME
			[F1

SHIFT> menu.

If the PREROLL button is pressed when the IN point has not been registered, the current tape position is automatically registered as the IN point (but only when ENA has been selected as the setup menu item No.305 (AUTO ENTRY) setting).

When the PREROLL button is pressed together
with the IN (A IN) or OUT (A OUT) button, the tape
can be cued up to the registered point concerned.
To cue up the tape for the cue time registered on
the HOME, PF1 or PF2 screen, press the
PREROLL button while holding down the	key	F
among the number keys.

OIN (A IN), SET and OUT (A OUT) buttons

When the IN (A IN) or OUT (A OUT) button is pressed together with the SET button, the IN (A IN) or OUT (A OUT) point is registered.The A IN and A OUT buttons are used to register audio IN and OUT points that differ from the corresponding video points during audio split editing.

When an IN (A IN) or OUT (A OUT) point has been registered, the lamp of the IN (A IN) or OUT (A OUT) button which has registered that point lights. When these buttons are pressed after points have been registered, the IN (A IN) or OUT (A OUT) point value

appears on the counter display.

When the buttonC is pressed while holding down the

IN (A IN) or OUT (A OUT) button, the registration of the IN (A IN) or OUT (A OUT) point is cleared.

12