Panasonic AJ-HD1700PE Y STANDBY button, The same tape tension is applied as in the regular, If a

Parts and Their Functions

Front panel

Y Z [

EJECT

XL/L/M

- cassette

POWER

OFF

ON

Do not insert S-cassette

without adapter

CH

1

2

3

4

5

6

7

8

CUE

CH CONDITION

MONITOR

FULL/FINE

REMOTE

9P

50P

RS-232C

L

R

HEADPHONES

HOME

RF1

RF2ASSEM

ADJUST

SHTL

JOG

VAR

PUSH-INTER

VIDEO

UNITY

TC

CUE

INSERT

REV

FWD

AUDIO

UNITY

DIAG

MENU

STAND BY

PLAYER

RECORDER

INPUT CHECK

SHIFT

F1

F2

F3

F4

F5

F6

SERVO

REC INHIBIT

AUDIO CH SELECT

A IN

A OUT

EDIT

PLAY

ABC

DEF

GHI

REC

CH

1

CH

5 CH 2

CH

6 CH 3

CH

7 CH

4

CH 8

7

8

9

PREVIEW/

PRE-

JKL

MNO

PQRS

REVIEW

ROLL

4

5

6

BS

AUTO

TUV

WXYZ

TRIM

REW

STOP

FF

1

2

3

ENT

EDIT

SET

PUSH

IN

OUT

LOCK

0

C

T

F

FULL

REC

P8

REC

P8

REC

P8

REC

P8

FULL

YSTANDBY button

The same tape tension is applied as in the regular

stop mode. While the head drum is rotating, the button’s lamp lights to indicate that the standby ON

mode is now established.
If the button is pressed in		the	stop mode,		the
standby OFF mode is established followed by the
half loading mode. At this time, its lamp goes off.
When the VTR is left in the stop mode beyond a
specific period of time, it is automatically set to the
standby OFF mode in order to protect the tape.
In the standby OFF mode, if this button or the
STOP button is pressed, the VTR is set to the
standby ON mode.	If a		button	other than the
STOP button is pressed, the		VTR is set to the
mode that corresponds to the button pressed.
The time taken by the VTR		to	transfer	to	the
standby OFF mode can be selected using a setup
menu item.

ZPLAYER and RECORDER buttons

These buttons are operated if the VTR is to be used as a recorder to conduct editing operations with a VTR equipped with an RS-422A serial interface remote control connector (9 pins). Neither button works when the VTR is used on its own.

PLAYER: When this button is pressed, its lamp lights to indicate that the player connected to the VTR can be operated by remote control. The VTR’s editing and tape transport system buttons

can now be used to control the player.

RECORDER: When this button is pressed, its lamp lights to indicate that the editing and tape transport system buttons can now be used to operate the recorder (this VTR).

•When the PLAYER button or RECORDER button is pressed while ENA has been selected as the setup menu item No.200 (PARA RUN) setting, the lamps of both buttons light to indicate that the VTR now serves as the master unit for parallel run operations. However, when this setting is used, it is no longer possible to perform external control from the REMOTE connector (9 pins).

[INPUT CHECK button

Only while this button is held down are the input signals from the monitor output connector output to enable the input video and audio signals to be monitored.

The time code generator can be checked on the time code display.

Select LATCH as the setup menu item No.517 (TCG OUT) setting in order to continue displaying the time code generator value even after the INPUT CHECK button has been released.

<Note>

The INPUT CHECK function does not work for the CUE signal and SDTI signals. Input signals can be monitored in the E-E mode.

14