Panasonic AJ-HD1700PE operating instructions Video

Setup menus

<VIDEO>

No./Item							Description of setting
600* 1	For selecting the video signal which is to be input.
	0000		INT SG					:
VIDEO IN SEL		The internal signal selected by the VIDEO INT
		SG item is generated.
		0001			HDSDI			:
		The serial video signal which has been input to the
		HD SDI IN connector is selected.
	0002				SDTI			:(In 59/60 Hz mode)
		The compressed IF signal which has been input to
		the SDTI IN connector is selected. (This setting
		does not appear when the AJ-YAC15P optional
		board has not been installed.)
	0002		SD SDI					:
		The serial video signal which has been input to the
		SD SDI IN connector is selected. (This setting does
		not appear when the AJ-UC1700G optional board
		has not been installed.)
1	For selecting the type of internal signal.
601*
		0000		100 % CB				:
VIDEO INT SG		A 100% color bar signal is selected.
	0001		75 % CB					:
		A 75% color bar signal is selected.
	0002		SMPTE					:
		An SMPTE color bar signal is selected.
	0003				ARIB			:
		An ARIB color bar signal is selected.
	0004					MB		:
		A multiburst signal is selected.
	0005			RAMP				:
		A ramp signal is selected.
	0006		BLACK					:
		A black signal is selected.
	0007					PLL		:
		A PLL signal is selected.
	0008					EQ		:
		An EQ signal is selected.
1	For selecting how to process the serial input.
602*
	0000			DR OFF				:The 8 higher bits after rounding up
SDI IN MODE								the 2 lowest bits are recorded.
	0001		DR ON					:The signal with 8 higher bits, obtained
								by dynamic rounding, is recorded.
603	For selecting					whether			to	mute	the video output
	signals		if		LOW		RF	has		been	detected during
V-MUTE SEL	playback.
	0000		N MUTE					:	The signals are not muted.
										(They are frozen.)
		0001			GRAY			: The signals are muted with gray.
		0002	BLACK					: The signals are muted with black.
	0003		NOISE					: The signals are muted with noise.
604*1	For selecting						the	freeze mode of the still
	pictures and slow playback mode.
FREEZE SEL		0000				FIELD		: Field freeze, field slow
	0000			FRAME				:		Frame freeze, frame slow

*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode has been selected as the system menu item.

*4: This item is not displayed when the 23/24 Hz or 25 Hz (HD) mode has been selected as the system menu item No.25 (SYSTEM FREQ) setting.

*5: This item is not displayed when the 25 Hz (HD or SD) mode has been selected as the system menu item No.25 (SYSTEM FREQ) setting.

The underlining (__) denotes the factory setting mode.

No./Item							Description of setting
605*1	During field slow playback, vertical interpolation is
	conducted automatically to minimize the up/down
INTERPOLATE	movement of the playback pictures.									However, this
	setting enables the interpolation operation to be
	forcibly set to OFF.
	0000				OFF			:	The interpolation is forcibly set to OFF.
	0001				AUTO			:	During slow playback, the interpolation
									is automatically set to ON.
606	For selecting the SD SDI or MONITOR output
	signal.
SD MONI O		0000				MONI		::	The MONITOR signal is output.
SEL	0001					SDI		:	The same video signal as the
									one output from the SD SDI
									OUT1 connector is output
	<Note>
	When 1 (SDI) is selected, the time code and other
	information are not superimposed on the display.
4	For selecting the picture frame during down-
620*
	conversion.
DOWNCON			0000			FIT_V		:	Side cut mode
MODE	0001				FIT_H			:	Letter box mode
	0002				FIT_HV			:	Squeeze mode
	0003					14:9: Semi letter box 14:9
	0004				13:9:				Semi letter box 13:9
5	For			selecting the				picture frame		during up-
621*
	conversion.
UPCON MODE			0000			FIT_V		:	Side panel mode
	0001				FIT_H			:	Top and bottom cut in vertical
									direction
	0002				FIT_HV			:	Stretch mode
622	For selecting the horizontal frequency band
	during down-conversion and line conversion
D/C RESP	(1080i				<> 720p).
H		0000				WIDE
		0001				STD
623	For			selecting the				vertical frequency band
	during down-conversion and line conversion
D/C RESP	(1080i				<> 720p).
V		0000				WIDE
		0001				STD
5	For selecting the horizontal frequency band
624*
	during up-conversion and line conversion.
U/C RESP		0000					STD
H	0001				NARROW
625*	For			selecting the				vertical frequency band
	during up-conversion and line conversion.
U/C RESP		0000					STD
V	0001				NARROW
626	For			accentuating the					horizontal	contours
	during down-conversion and line conversion
D/C ENH	(1080i				<> 720p).
H	0000					0dB
	0001				i0.7dB
		0002				i1dB			<Note>
	0003				i1. 2dB
	0004				i1.5dB				The numbers on the superimposed
	0005					i2dB			display are approximations only.

93