Panasonic AJ-HD1700PE MONITOR SELECT buttons, factory setting, METER FULL/FINE selector button

Parts and Their Functions

Front panel

<

8 9 : =

;

EJECT

XL/L/M

- cassette

POWER

OFF

ON

Do not insert S-cassette

without adapter

CH

1

2

3

4

5

6

7

8

CUE

CH CONDITION

MONITOR

FULL/FINE

REMOTE

9P

50P

RS-232C

L

R

HEADPHONES

HOME

RF1

RF2ASSEM

ADJUST

SHTL

JOG

VAR

PUSH-INTER

VIDEO

UNITY

TC

CUE

INSERT

REV

FWD

AUDIO

UNITY

DIAG

MENU

STAND BY

PLAYER

RECORDER

INPUT CHECK

SHIFT

F1

F2

F3

F4

F5

F6

SERVO

REC INHIBIT

AUDIO CH SELECT

A IN

A OUT

EDIT

PLAY

ABC

DEF

GHI

REC

CH

1

CH

5 CH 2

CH 6 CH

3

CH

7 CH

4

CH 8

7

8

9

PREVIEW/

PRE-

JKL

MNO

PQRS

REVIEW

ROLL

4

5

6

BS

AUTO

TUV

WXYZ

TRIM

REW

STOP

FF

1

2

3

ENT

EDIT

SET

PUSH

IN

OUT

LOCK

0

C

T

F

FULL

REC

P8

REC

P8

REC

P8

REC

P8

FULL

8MONITOR SELECT buttons

These buttons are used to select the audio signals which are to be output to the monitor L and R

connectors and headphones jack.
• When OFF has been selected as the					M
						F6
MIX setting on the <AUDIO SHIFT2> menu
(factory setting):
Each time the L (or R) button is pressed, the
signal to be output to the monitor L (or R)
connector is changed in the following sequence						>
and displayed on the audio level meter: CH1
CH2	> CH3	> CH4	> CH5 > CH6 > CH7 >
CH8	> CUE	> CH1, etc.
• When L, R or L/R has been selected as the
							F6
M MIX setting on the <AUDIO SHIFT2> menu:
At this setting, the signals of a multiple number of
channels can be mixed and output.
When the number key corresponding to the
channel whose signals are to be monitored is
pressed while the L (or R) button is held down,
that channel is selected and its signals are
displayed on the audio level meter.					(By
performing the same operation, the selected
channel can be de-selected.)
However, a maximum of only two channels from
CH1	to CH4 and a maximum of			only	two
channels from CH5 to CH8 can be selected.
Example of channels which can be selected:
CH1	i CH3	i CH5	iCH8	“ OK
CH1 + CH2 + CH4			“ NG

9METER (FULL/FINE) selector button

This button is used to select the scale display for the audio level meter.

FULL mode: Depending on the setting selected for the

setup menu item No.763 (METER SCALE)*, either the

j¶ to 0 dB (reference level:		j20 dB/ j18 dB**) or j¶
to i20 dB (reference level: 0 dB) range is displayed.
FINE mode:	Depending on the setting selected for the
setup menu item No.763 (METER SCALE)*, either the
j24 to j15 dB (reference level:		j20 dB/ j18 dB**) or

j4 to i5 dB (reference level: 0 dB) range is displayed on a scale with 0.5 dB increments.

*This menu is not displayed for AJ-HD1700E.

** j20 dB is applied for AJ-HD1700P and j18 dB is for AJ-HD1700E.

:REMOTE buttons and RS-232C display

These buttons are used when this VTR is to be controlled from an external component using the REMOTE, RS-232C or parallel connector.

9P: When this button is pressed for 2 or more seconds, its LED lights, and the 9-pin REMOTE connector is selected.

50P: When this button is pressed for 2 or more seconds, its LED lights, and it is possible to control the VTR from a unit which has been connected using

the 50-pin parallel mode connector.

RS-232C display: This LED lights when communi- cation has been enabled between the VTR and the

unit which has been connected to the RS-232C connector.

;AUTO OFF lamp

This lamp lights when a problem has occurred with

the VTR’s operation, and details of the problem appear on the time code display.

<LCD monitor

This monitor is used to check the tape’s playback pictures and EE pictures.

When an HD tape is played back, the signals are down- converted and displayed in the letter-box screen format. When an SD tape is played back, the signals are displayed using a 4:3 aspect ratio.

On-screen menus can also be displayed on the monitor.

If the VTR is left in a state where no controls on the front panel are operated or where the tape is not running, the monitor display is automatically turned off in order to protect the monitor. When the next VTR operation is started, the monitor display comes back on.

<Note>

Although the LCD monitor has been manufactured using technology with extremely high levels of precision, some pixels may be missing from parts of the screen or some pixels may remain lighted. These missing or lighted pixels will not be recorded.

It should also be borne in mind that this is not indicative of a malfunction.

=Function buttons

These buttons are used to perform the operations of

the function menus (see page 38 for details) and

setup menus.

:This is used to switch the pages of the current

SHIFT

function menu (

to

).

F1

F6

to

: These

are

used to change the settings of

F1

F6

the setting items enclosed in the frame at the bottom of

the time code display.

To change a setting, keep pressing the corresponding

function

button

(

)

the desired

F1

F6

numerical value appears; alternatively, press the corresponding function button to highlight the setting of the setting item, and then turn the ADJUST dial until the desired numerical value is obtained.

9