Panasonic AJ-HD1700PE ? ANALOG COMPOSITE VIDEO OUT connectors, B HD REF OUT connector, Rear panel

Parts and Their Functions

Rear panel

>

D

B

H

TC

PUSH

CUE

PUSH

MON

HD SDI

IN

OUT 1

OUT 2

OUT 3

MONITOR (SUPER)

IN

IN

L

ACTIVE

THROUGH

SDTI

SD SDI

AUDIO

CH1·2

CH3·4

CH5·6

CH7·8

IN

OUT

OUT

R

IN

CH1·2

CH3·4

CH5·6

CH7·8

(OPTION)

AUDIO

OUT

OUT

MONITOR

AUDIO IN

(SUPER)

DIGITAL AUDIO

CH 1

PUSH

CH 2PUSH

CH 3PUSH

CH 4PUSH

ANALOG

VIDEO OUT

SD REF IN

HD REF IN

HD REF OUT

1

PARALLEL

ON

ON

ENCODER

AC IN

AUDIO OUT

75≠

75≠

REMOTE

CH 2

CH 4

2(WFM)

REMOTE

CH 1

CH 3

OFF

OFF

IN/OUT

SD

3(SUPER)

REF OUT

REMOTE

R

OUT

SIGN

L

RS-232C

E

G

D

M

O

T

E

? @ A C G F

E

>SD SERIAL DIGITAL COMPONENT AUDIO and VIDEO OUT connectors

The digital component audio and video signals complying with the SMPTE 259M-C, 272M-A or 294M standard are output from these connectors. They are output during DVCPRO25M, 50M, DV or DVCAM interchangeable playback or when signals

are down-converted and output. Signals containing TC, menu or other superimposed information can be output from the SD SDI MONITOR.

Using setup menu item No.606 (SD MONI O SEL), it is also possible to make the SD SDI MONITOR output the same output as SD SDI OUT1 (no

information superimposed).
When “SD SDI” has been selected as the	(VID
			F1
IN) setting on the <VIDEO> menu and “THRU” has
been selected as the No.107 (EE MODE SEL)
setting, no information is superimposed onto the SD
SDI MONITOR output signals in the EE mode, and
the same output as SD SDI OUT1 is delivered.
• The AJ-UC1700G optional board is required in
order to select “SD SDI” as the	(VID
		F1IN)

setting on the <VIDEO> menu.

•For INPUT CHECK, refer to the INPUT CHECK output table on page 15. Note that the signals are muted during line conversion.

<Note>

In the 23/24 Hz mode, the system phase of the SD SDI output and analog composite video output is subject to change when the tape has been set to

travel at the normal speed (1	k) so that the HD SDI
output and phase will be aligned.

?ANALOG COMPOSITE VIDEO OUT connectors

The analog composite video signals are output through these connectors. They are output during DVCPRO25M, 50M, DV or DVCAM interchangeable playback or when signals are down-converted and output.

Video signals containing superimposed information can

be output through the VIDEO OUT 3 connector. Whether

the superimposing is to be set ON or OFF is selected using the setup menu item No.005 (SUPER).

The waveform monitor (WFM) signal can be output from the VIDEO OUT 2 connector.

The signals which can be switched using the menu items

are the TC, CTL, video, RF L/R and ENV L/R signals. There is no INPUT CHECK function. The signals are muted during line conversion.

@SD REF IN connectors and 75-ohm termination switches

These are the SD reference video signal input connectors. Input composite signal with color burst.

For termination, set the termination switch to ON.

AHD REF IN connectors and 75-ohm termination switches

These are the HD reference video signal input connectors. Input tri-level sync signals with both positive and negative polarities.

For termination, set the termination switch to ON.

BHD REF OUT connector

This is the HD reference video signal output connector for external synchronization. Tri-level sync signals with both positive and negative polarities are output.

The output based on SYS FORMAT of menu item No.020 is delivered from the connector.

CSD REF OUT connector

The composite signal used for external synchronization (black burst signal) is output from this connector.

DDIGITAL AUDIO IN and OUT connectors

These are the input and output connectors of the digital audio signals that comply with the AES/EBU standards.

ERemote control connectors

These connectors make it possible to use two of these VTRs or to connect this VTR to an external controller so that this VTR can be operated from an external component.

Two remote control connectors are provided: one for IN/OUT uses and the other for OUT uses only. IN/OUT: For connection with an external controller

For connection during deck-to-deck operations OUT: For connection during parallel run operations

For loop-through uses

FENCODER REMOTE connector

An external encoder remote controller is connected to this connector when the video output signal settings are to be adjusted from an external component.

GRS-232C connector

HPARALLEL REMOTE connector

This is used when the VTR is to be operated from an external component.

19