Panasonic AJ-HD1700PE operating instructions Time Code

Setup menus

<TIME CODE>

No./Item				Description of setting
500* 4	For selecting whether or not to output the
	VITC signal at the positions selected by setup
VITC BLANK	menu items No.501 (VITC POS-1) and No.502
	(VITC POS-2).
	0000		BLANK		: The VITC signal is not output.
		0001	THRU		: The VITC signal is output.

<Note>

Only the SD output takes effect at this setting.

501*4	For setting the position where the VITC signal
	is to be inserted.
VITC POS-1	<59/60Hz>			<50Hz, 25Hz (SD)>
	0000		10L	0000	7L
	:		:	:	:
	0006		16L	0004	11L
		:	:	:	:
	0010		20L	0015	22L

<Notes>

•The same line as the one selected by the setup menu item No.502 (VITC POS-2) cannot be selected.

•Only the SD output takes effect at this setting.

502*4	For setting the position where the VITC signal
	is to be inserted.
VITC POS-2	<59/60Hz>				<50Hz, 25Hz (SD)>
	0000		10L		0000	7L
	:		:		:	:
	0008			18L	0006	13L
		:	:		:	:
	0010		20L		0015	22L

<Notes>

•The same line as the one selected by the setup menu item No.501 (VITC POS-1) cannot be selected.

•Only the SD output takes effect at this setting.

503*1	For setting the synchronization of the internal
	time code generator.
TCG MODE	0000		REGEN		:
		The time code reader is synchronized with the
		time code which is read from the tape.
	0001			PRE	:
		Presetting is enabled at the operation panel or
		by the remote controller.
	0002			AUTO	:
		The	REGEN			and	PRE	settings		are
		automatically switched in accordance with the
		operation mode.
		In the editing mode: REGEN is selected.
		In all other modes: PRE is selected.
504*1	For setting			when the			internal		time	code
	generator is to advance depending on the
RUN MODE	operation mode.
	0000			REC	:
		The time code generator is advanced during
		recording.
	0001		FREE		:
		The time code generator is advanced while the
		power is		on	regardless		of which		operation
		mode is established.

*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode has been selected as the system menu item No.25 (SYSTEM FREQ) setting.

*2: This item is not displayed when the 23/24 Hz or 25 Hz (HD) mode has been selected as the system menu item No.25 (SYSTEM FREQ) setting.

The underlining (__) denotes the factory setting mode.

No./Item					Description of setting
505*1	For selecting the					regeneration			signal when
	REGEN has been selected as the TCG (time
TCG REGEN	code generator) mode.
	0000			TC&UB			:
		Regeneration applies to both the time									code
		and user’s bit.
	0001			TC			:
		Regeneration applies only to the time code only.
	0002			UB			:
		Regeneration applies only to the user’s bit only.
506*1	For selecting the					editing		mode		range when
	the VTR is operating in the REGEN mode
REGEN MODE	while		performing editing						operations		with
	“AUTO” selected as the setup menu item
	No.503 (TCG MODE) setting.
	0000			AS&IN			:
		Regeneration				applies		during		assemble	or
		insert editing.
	0001		ASSEM				:
		Regeneration applies during assemble editing.
	0002		INSRT				:
		Regeneration applies during insert editing.
507*1	For selecting the time code to be used when
	HD SDI		or SD SDI has been selected as the
TC SOURCE	setup		menu item No.600 (VIDEO IN SEL)
	setting when an external time code is to be
	used.
	[When HD SDI has been selected]
	0000			INT			:
		The	time code of the internal time code
		generator is used.
	0001		EXT_L				:
		LTC of the TIME CODE IN connector is used.
	0002			SLTC			:
		The	LTC information added to the								serial
		signals which are input to HD SDI IN is used.
	0003		SVITC				:
		The VITC information added to the serial
		signals which are input to HD SDI IN is used.
	[When SD SDI has been selected]
	0000			INT			:
		The	time code of the internal time code
		generator is used.
	0001		EXT_L				:
		LTC of the TIME CODE IN connector is used.
	0002			VITC			:
		The VITC information added to the serial
		signals which are input to SD SDI IN is used.
	<Note>
	If the VIDEO IN SEL input selection is changed, the time
	code is converted as shown below.
	[HD_SDI]						[SD_SDI]
	INT				↔		INT
	EXT_L				↔		EXT_L
	SLTC				↔		EXT_L
	SVITC				↔		VITC

91