Panasonic AJ-HD1700PE Moving to registered points, Page number display area, Page operations

Function menus

<CUE>

A maximum of 60 cue points can be set on these menu screens. When “AUTO” has been selected as the (PAGE) setting on the AUTO PAGE mode <CUE SHIFT> menu, up to 10 pages of cue points with 6 cue points on each page can be managed on a page-by-page basis.

The 60 cue points are indicated using the page number display and registered point display areas.

<Note>

Cue points cannot be registered, prerolled, etc. if a setting other than “ENA” has been selected as the setup menu item No.001 (LOCAL ENA) setting in the REMOTE mode.

Page number display area	Cue point data display areas
Registered point display area

SHIFT F1 F2 F3 F4 F5 F6

F3

Moving to registered points

The highlighting on the registered point display area is moved by turning the ADJUST dial. It is moved in the ascending order of points when the dial is turned clockwise and in the descending order of points when

it is	turned	counterclockwise.				W hen “AUTO” has
been	selected	as the	(PAGE)		setting	on the
				F3

<CUE SHIFT> menu, the highlighting can be moved also to the previous or next page.

•Depending on the setting selected for (ROTATE) on the <CUE SHIFT> menu, the following applies to moving the highlighting in the ascending order of points.

When “OFF” is set:

The highlighting cannot be moved from page 9 to page 0.

When “ON” is set:

The highlighting can be moved from page 9 to page 0.

•In moving in the descending order of points, the highlighting cannot be moved from page 0 to page 9.

F4

SHIFT F1 F2 F3 F4 F5

Page number display area

The page number from 0 to 9 is indicated here.

Registered point display area

On each page, six cue point data managed by registered point numbers are displayed. A point whose registered point number is highlighted is targeted for registration and search.

Shown below is the correlation between the page numbers and registered point numbers.

Page no.	Registered points Page no.	Registered points
0	01–06	5
1	11–16	6
2	21–26	7
3	31–36	8
4	41–46	9

F6

51–56

61–66

71–76

81–86

91–96

Search point and registered point operations

Each	time the		(MODE)F3	button	of	the <CUE>
menu	is pressed, the	search mode and			cue	point

registration mode are switched alternately. Perform the search point or registered point operations in the respective mode.

•When the power is turned on, the search point or registered point, whichever was established when

the power was last turned off, is established.
• When the setting for	(PAGE)F3 or	(ROTATE)F4

on the <CUE SHIFT> menu has been changed, “01” (page 0/point no.1) is set for both the search and registered points.

Cue point registration mode

It is possible to register points to which the tape is to be prerolled. When the display page has been

changed using the		or	(NEXT)
	(PREV)F1			buttonF2

on the <CUE> menu, the following applies depending

on the setting for (PAGE)F3 on the <CUE SHIFT> menu.

Page operations

Pages can be scrolled in the forward or reverse direction
using the
		[F1]F1 (PREV) or	[F2]F2 (NEXT) function buttons.
• Depending on the setting selected for
				[F4]F4 (ROTATE)
on the <CUE SHIFT> menu, the following applies to
scrolling pages in the forward direction.
When “OFF” is set:
Page 0	cannot be scrolled forward from page 9.
When “ON” is set:
Page 0	can be scrolled forward from page 9.

•In scrolling pages in the reverse direction, page 9 cannot be scrolled in reverse from page 0.

When “MANU” is set:

Both the search and registered points move to the top of the changed page.

When “AUTO” is set:

Only the registered point moves to the top of the changed page; the search point does not move.

52