Panasonic AJ-HD1700PE Binary GP, Iso, Page/Line, Phase Corr, TCG CF Flag, Tc Out Ref, HD Embd LTC

Setup menus

<TIME CODE>

(continued)

No./Item

Description of setting

508* 1

For setting how the user’s bit of the time code

generated by the TCG is to be used.

BINARY GP

0000

000

:

NOT SPECIFIED (no character set specified)

0001

001

:

ISO

CHARACTER (8-bit character set

complying with ISO646, ISO2022 standards)

0002

010

:

UNASSIGNED 1 (undefined)

0003

011

:

UNASSIGNED 2 (undefined)

0004

100

:

UNASSIGNED 3 (undefined)

0005

101

:

PAGE/LINE

0006

110

:

UNASSIGNED 4 (undefined)

0007

111 :

UNASSIGNED 5 (undefined)

509

For

selecting

whether to

exercise

phase

correction

control over the LTC which is

PHASE CORR

generated by the TCG.

0000

OFF

:

Phase correction control is not exercised.

0001

ON

:

Phase correction control is exercised.

510*1

For selecting whether to set the CF flag of the

TCG to ON or OFF.

TCG CF FLAG

0000

OFF

:

The CF flag is set to OFF.

0001

ON

:

The CF flag is set to ON.

2

For

selecting

the

drop frame or non-drop

511*

frame mode for CTL and TCG.

DF MODE

0000

DF

:

The

drop

frame

mode

is

selected.

0001

NDF

:

The non-drop frame mode is

selected

.

<Note>

This DF mode setting takes effect only when LOCAL is

selected or when “ENA” has been selected as the setup

menu item No.001 (LOCAL ENA) setting.

512*

For

switching the

phase of the time code,

which is

output

from the TIME CODE OUT

TC OUT REF

connector,

in response to the external LTC

input when a setting other than “INT” has

been selected for setup menu item No.507 (TC

SOURCE). (In EE mode only)

0000

V

OUT

:

The phase is aligned with the

output image.

0001

TC IN

:

The phase is aligned with the

external time code input

.

SBC (sub code data) area:

This is an area on the helical track, and it is separate from the video and audio data area. The time codes, recording dates and times and other tape control information complying with SMPTE/EBU standards are stored here. As with the conventional LTC (linear time code), the time code can be read even during rewinding or fast forwarding. It can also be read out when the tape has stopped.

VAUX (video auxiliary data) area:

This area is to be found in the video data area on the helical track.

The additional information relating to the video data is stored here.

*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode has been selected as the system menu item No.25 (SYSTEM FREQ) setting.

*2: This item is not displayed when the 23/24 Hz, 25 Hz (HD or SD) or 50 Hz mode has been selected as the system menu item No.25 (SYSTEM

FREQ) setting.

No./Item

Description of setting

513

For selecting how to output the VITC which is

superimposed on the output video signal.

VITC OUT

0000

SBC

:

In the playback mode, the time code recorded

in the SBC area is output.

0001

VAUX

:

In the playback mode, the time code recorded

in the VAUX area is output.

<Note>

The VITC information detected by the HD serial input is

automatically recorded in the VAUX area when the video

signals are recorded

.

514

For

selecting

whether to

superimpose

the

VITC information on the HD serial output.

HD

EMBD

0000

OFF

:

VITC

The VITC information is not superimposed.

0001

ON

:

The VITC information is superimposed.

515

For

selecting

whether to

superimpose

the

LTC information on the HD serial output.

HD EMBD LTC

0000

OFF

:

The LTC information is not superimposed.

0001

ON

:

The LTC information ist superimposed.

516*

For

selecting

the

processing

to align

the

phase of the time code which is output from

TC OUT ADV

the TIME CODE OUT connector.

Normally, the time code which is output from the

TIME CODE OUT connector is aligned with the

output video and audio. If so required by the

connection with an external component or for

some other reason, this item makes it possible to

set

the

mode

for aligning the

phase

with

the

input.

0000

OFF

:

The phase alignment processing is not

conducted. The time code which is output

from

the TIME CODE OUT connector is

aligned with the output video and audio.

0001

EDIT

:

During playback when an editing mode has

been

selected and during editing, the time

code which is output from the TIME CODE

OUT connector is aligned with the input video

and audio. In all other modes, it is aligned with

the output video and audio

.

517*

For

selecting

whether

to

latch

the TCG

display and LTC output during INPUT CHECK.

TCG OUT

0000

MOMENT

:

The INPUT CHECK mode is established only

while the INPUT CHECK key is held down.

0001

LATCH

:

When the INPUT CHECK key is pressed, the

INPUT CHECK mode is established; even

when

it is released, the mode remains

unchanged. The selection is released when

the video output is set to a mode other than the

EE mode.

The underlining (__) denotes the factory setting mode.

92