Updating from the Download Mode | Pitney Bowes J693 instruction

5.6.2Updating from the Download Mode

Required Update Procedure for Application Version 2.08 or earlier*

	Step	Displayed Message				Operator Action		Comment(s)
	1.	QSOQZSPRRPQQ#L"RQ				Press and hold the		The Boot Loader version
	1.	QSOQZSPRRPQQ#L"RQ				Press and hold the		The Boot Loader version
						PAUSE and TEST		is displayed.
						keys while turning
						keys while turning		Note: This information
						‘On’ the printer to		will vary with the printer
						enter the Download		model and Boot Loader
						Mode.		version.

	2.					Using the DOS		The printer is ready to
	2.	"""				Using the DOS		The printer is ready to
						copy command,		accept the new application
						copy the filename		version.
						copy the filename		version.
						to the printer (see		Note: The parallel port
						Step 2 in Section		(LPT1) must be used to
						5.6.1).		write to the printer.

	3.					No action required.		The printer is receiving
	3.	"""				No action required.		The printer is receiving
								the new image (program).


	4.					No action required.		The program has been
	4.	""				No action required.		The program has been
								received and verified; now
								Flash memory is cleared
								Flash memory is cleared
								of the previous
								application.

	5.					No action required.		The new program is being
	5.	"""				No action required.		The new program is being
								written into Flash memory.
								Upon completion, the
								Upon completion, the
								printer will automatically
								reset, starting the new
								application; however,
								before continuing, the
								printer must be re-
								calibrated; see Section 5.2.

*This can also be used as an alternate download method for all other version levels.

J693

61

Image 71

Pitney Bowes J693 manual Updating from the Download Mode

Contents

J693 Page Firmware Software Agreement Copyright Information Agency Compliance and Approvals Important Safety Instructions Page Getting Started Setting Up the PrinterUsing the Front Panel Printer Overview Specifications Adjusting and Maintaining the PrinterTroubleshooting Appendix D Appendix aAppendix B Appendix CPage About this Printer Printing Standard Features Inspection J693 Installing the Printer Serial Port Communications Interfacing Loading Media Page Label Backing Removal 3Loading Ribbon Ribbon routing path Ribbon Removal J693 Operating the Front Panel Ready Mode Normal Operation Ready Light ‘On’ Menu Mode Configuration Ready Light ‘Flashing’ Quick Test M de Print Test Labels Liquid Crystal Display Indicator LightsLCD Display Level 1 Reset Resetting the Printer Navigating the Menu System Enter = YES Enter PasswordKeep Host CHANGES? Label Length Media SettingsMedia Type Sensor Type Print Control Cutter ModulesPresent Sensor END of Print Gpio PortGpio System Settings Code Configuration LevelUpgrade Printer Printer KEY Format Attributes SET Factory DefaultsImaging Mode Allegro Emulation Pause ModeSecurity Units of Measure Parallel Port a CommunicationsSerial Port a Serial Port B Control Codes Host SettingsTimeout Feedback Mode Sensor Readings HEX Dump ModeOptions Testing Test Description Conditions Understanding the Display MessagesUser Prompts and Condition Messages User Prompts and Condition Messages Reset in PROGRESS’ Print Quality Label Printing from the Quick Test Mode Configuration Label Quick Ribbon Test Label Dot Test Pattern Label User Defined Label Validation Label Media Type Sensor Type Sensor Eye Mark Position Media Sensor AdjustmentPage Standard Calibration Positioning CalibrationMedia Sensor Calibration Step Operator Action Displayed Message Comment Press the key to Reflective media place Die-cut stock removeNotched stock place Key to back out Displayed Message Action Comment Advanced Entry Calibration Hqlrvi Jqqhqlrvi Using the Gain Number Using Key Jrxyjtsjqrr Burn Line Adjustment Printhead AdjustmentsPage Printhead Replacement Recommended Cleaning Schedule Area Method Interval Cleaning Schedule Cleaning the Printhead In5.5.2 Cleaning the Platen Roller Updating the Application Program Cleaning Interior and Exterior Surfaces Updating from the Ready Mode Updating from the Download Mode Descriptions / Causes / Solutions Application Update ProblemsApplication Update Error Messages Updating the Boot Loader Program J693 If experiencing this problem… Try this solution… Troubleshooting Tips If experiencing this problem… Try this solution… If no image is on the used ribbon If an image is on the used ribbon If experiencing this problem… Description Possible Solutions Fault and Warning Messages Fault Messages Ribbon supply hub If media is not moving If media is moving Description Action Hex Dump Mode Electrical Printer SpecificationsBar Codes Fonts Mechanical Printing SpecificationsEnvironmental Requirements Char Dec Hex Ascii Control Code Chart 128 160 192 224 129 161 Font Valid Ascii Characters Available Fonts and Bar Codes Font Height Width Spacing Page Page Bar Valid Ascii Characters Code Type Bar Code Summary Data Bar Code F EAN-13 Bar Code p Postnet Bar Code O Code Bar Code K Plessey Bar Code S UCC/EAN Code 128 Random Weight Module Assignments Print Resolutions and Maximum Widths Feed Speed Settings and DefaultsJ693 Function Speed Range Default Setting Print Required Software Comment Menu System Multi-Language Support Next J693 OAdvance File Handling Information Menu Language Error Message DescriptionPage J693 Page Page Page Page J693