Source Connections

Input Facilities

The following source types can be connected to the inputs :

•RGB Tri-level Sync

•RGB Composite, Separate or Sync on green

•Component Video

•Component Video with Tri-level Sync

AC Input

OFF/ON 75 Ohm

S-Video

OFF ON

Future Expansion INPUT 4/5 INPUT 2

		OFF/ON
		75 Ohm
		Green: Operation
	12 Volt	Red: Standby
	12 Volt
Video	Trigger	Status
Video		Status

INPUT 1

Which source to which input
Source No.	Projector Input	Remote Button No.
1	Comp. Video*	1 (not used)
2	S-Video/Comp. Video*	2 (not used)
3	RGB	3
4/5	RGB	4 or 5
4/5	Component Video	6
4/5	RGB with Tri-level Sync	7
4/5	Component Video
	with Tri-level Sync	8

* Not used in the DTV-1200

Page 13

Image 13

Runco DTV-1200 owner manual Source Connections, Source No Projector Input Remote Button No

Contents

DTV-1200 Page Table of Contents Page Page Safety Instructions Safety Instructions Power cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugPage Page Limited Warranty Effective Warranty Date Connections Power Connection to Projector Source No Projector Input Remote Button No Source Connections RGB Source with Composite Sync to Input 4/5 RGB Source to InputInput Select Input Component Source to Input 4/5 RGB Source with Tri-level Sync to Input 4/5RS-232 Connection Getting Started Remote Control & Local Keypad Audio controls not used Projector Warm UP Stationary Image Warning Front of projector Remote Commands to the Projector Projector Address Input Selection via the Remote Contrast Control Brightness ControlColor Saturation Control Not used on the DTV-1200 Adjustment Mode Start UP of the Adjustment Mode Main Menu Main Menu Image Control Color Adjust Format Select Compose Eye-Q Touch Up Eye-Q Control Eye-Q Auto Converge Main Menu Adjustment Mode Service Menus Entering the Service Menus Enter Password Random Access Adjustment Mode Random Access Adjustment ModeRandom Access Selecting Setup Pattern VGA Internal Cross Hatch Pattern Picture Tuning Random Access Adjustment Mode Selection MenuRandom Access Adjustment Mode Picture Tuning Picture Tuning Color Balance Gain adjustment affects the brightest areas of the imageColor Balance Color Balance Picture Tuning Sync Fast/Slow AdjustmentsColor Balance Piture Tuning Clamp TuningPeaking Peaking Horizontal Phase Adjustments Geometry AdjustmentsRandom Access Adjustment Mode Geometry Phase Raster Shift Adjustments Forbidden Area Left-Right East-West AdjustmentsProjected Raster CRT Faceplate Border Phosphor Coarse Shift LEFT-RIGHT What can be done? Left Side CorrectionStart up Left Side Correction Geometry Top-Bottom North-South AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-S TOP BOW TOP Keystone Bottom BOW Bottom Keystone TOP-BOTTOM Size Horizontal Size Adjustments Linearity V Size Vertical Linearity AdjustmentsLinearity Blanking Adjustments Vertical Size AdjustmentsBlanking Blanking Correct by pushing the cursor keys up or down Converge Adjustment Convergence AdjustmentsConvergence Convergence Focusing FocusingFocusing Midpoint Bottom TOPLeft Right Color SelectBlue on Source Color Select Service Mode Service ModeRandom Access Installation Service Mode Software version Configuration Projector SetupIdentification Text ON/OFF Projector SET-UP Run TimeIdentification RUN Time Change Password Change PasswordPassword Change Password Change Baud Rate Change Projector AddressProjector SET-UP Projector Address Baud Rate Warm Up On/Off Projector Warm UpProjector Warm UP Projector Warm Up Time Warm Up FrequencyProjector Warm UP Common Address Power Up Mode Memory Management Copy ModeCopy a Block Memory Management Deletion of Blocks Delete ModeDeleting Block by Block Deletion of All Blocks Covergence Mid Set to MidpositionDelete ALL Blocks SET to Midposition Convergence MID Undo R & B Convergence MidSET to Midposition Green Convergence MID Focus to Midposition Undo Green Convergence MidUndo Focus to Midposition East-West to Midposition North-South Settings to MidpositionUndo East-West to Midposition To Midposition Digital Vertical Linearity to Midposition Undo North-South Settings to MidpositionUndo Digital Vertical Linearity to Midposition DIG Vert Linearity MID Undo Digital Horizontal Linearity to Midposition Digital Horizontal Linearity to MidpositionAstigmatism to Midposition DIG HOR Linearity MID Undo All Settings to Midposition All Settings to MidpositionUndo Astigmatism to Midposition Common Settings Common SettingsDynamic Astigmatism Green Dynamic Astigmatism Gamma Corrections Common SettingsCRT Run In Cycle CRT RUN in Cycle CRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Menu Position Flyback Turnover PointFlyback Turnover Point Voltage Diagnostics 12C DiagnosticsI2C Diagnostics Decoder Projector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage Diagnostics Programmable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Adjustment Blocks Memory Blocks Adjustment Blocks and Source NumbersSource Numbers Block Header Example of Block Header Source input Source number Block header a RS-232 Codes Page TD = Throw Distance Factors CEILING/FLOOR Configuration Bottom View DimensionsSide View Front View Specifications Page RUMA-009450 rev

Source Connections

OFF ON

Source No.

Projector Input

Remote Button No.