Eye-Q Control, Eye-Q Touch Up | Runco DTV-1200 specs

How to store the settings to a new 'Format'?

1Push the cursor keys or to select a free format.

2Press ENTER to activate.

3Make any adjustment to the image.

4Quit the adjustment mode by pressing ADJUST.

The selected format will change from free to available.

Eye-Q Control

With the Eye-Q functions it is possible to automatically adjust the convergence of the image.

Start Up

1Push the cursor keys or to select 'EYE-Q control' (menu 1).

The selected item will change in color and a marker will be displayed in front of it.

2Press ENTER to select.

The 'EYE-Q control' menu will be displayed (menu 2).

MAIN MENU

Image Control

Eye-Q

Function Keys

Service Menus

Select with or then <ENTER> <EXIT> to return

EYE-Q CONTROL

EYE-Q Touch Up EYE-Q Auto Converge

Select with or then <ENTER> <EXIT> to return

menu 1

menu 2

Note: Before starting one of the EYE-Q functions, be sure the projector has warmed up for at least 20 min.

Eye-Q Touch Up

What can be done?

If you discover in the middle of the image a convergence misalignment between red, green and blue, the static convergence of this currently selected source can be adjusted with the touch up function.

26

Image 28

Runco DTV-1200 owner manual Eye-Q Control, Eye-Q Touch Up

Contents

DTV-1200 Page Table of Contents Page Page Safety Instructions Safety Instructions Mains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugPage Page Limited Warranty Effective Warranty Date Power Connection to Projector Connections Source Connections Source No Projector Input Remote Button No RGB Source with Composite Sync to Input 4/5 RGB Source to InputInput Select Input Component Source to Input 4/5 RGB Source with Tri-level Sync to Input 4/5RS-232 Connection Remote Control & Local Keypad Getting Started Audio controls not used Stationary Image Warning Projector Warm UP Remote Commands to the Projector Front of projector Projector Address Input Selection via the Remote Contrast Control Brightness ControlColor Saturation Control Not used on the DTV-1200 Start UP of the Adjustment Mode Adjustment Mode Main Menu Main Menu Color Adjust Image Control Format Select Compose Eye-Q Control Eye-Q Touch Up Eye-Q Auto Converge Adjustment Mode Main Menu Entering the Service Menus Service Menus Enter Password Random Access Adjustment Mode Random Access Adjustment ModeRandom Access Selecting Setup Pattern Internal Cross Hatch Pattern VGA Random Access Adjustment Mode Selection Menu Picture TuningRandom Access Adjustment Mode Picture Tuning Gain adjustment affects the brightest areas of the image Picture Tuning Color BalanceColor Balance Color Balance Picture Tuning Sync Fast/Slow AdjustmentsColor Balance Clamp Tuning Piture TuningPeaking Peaking Geometry Adjustments Horizontal Phase AdjustmentsRandom Access Adjustment Mode Geometry Raster Shift Adjustments Phase Left-Right East-West Adjustments Forbidden AreaProjected Raster CRT Faceplate Border Phosphor Coarse Shift LEFT-RIGHT Left Side Correction What can be done?Start up Left Side Correction Top-Bottom North-South Adjustments GeometryTOP-BOTTOM N-S TOP-BOTTOM N-S TOP-BOTTOM TOP BOW TOP Keystone Bottom BOW Bottom Keystone Horizontal Size Adjustments Size Linearity V Size Vertical Linearity AdjustmentsLinearity Vertical Size Adjustments Blanking AdjustmentsBlanking Blanking Correct by pushing the cursor keys up or down Convergence Adjustments Converge AdjustmentConvergence Convergence Focusing FocusingFocusing Midpoint Bottom TOPLeft Color Select RightBlue on Source Color Select Service Mode Service ModeRandom Access Installation Service Mode Projector Setup Software version ConfigurationIdentification Text ON/OFF Run Time Projector SET-UPIdentification RUN Time Change Password Change PasswordPassword Change Password Change Projector Address Change Baud RateProjector SET-UP Projector Address Baud Rate Warm Up On/Off Projector Warm UpProjector Warm UP Projector Warm Up Time Warm Up FrequencyProjector Warm UP Power Up Mode Common Address Copy Mode Memory ManagementCopy a Block Memory Management Delete Mode Deletion of BlocksDeleting Block by Block Deletion of All Blocks Set to Midposition Covergence MidDelete ALL Blocks SET to Midposition Undo R & B Convergence Mid Convergence MIDSET to Midposition Green Convergence MID Focus to Midposition Undo Green Convergence MidUndo Focus to Midposition North-South Settings to Midposition East-West to MidpositionUndo East-West to Midposition To Midposition Undo North-South Settings to Midposition Digital Vertical Linearity to MidpositionUndo Digital Vertical Linearity to Midposition DIG Vert Linearity MID Digital Horizontal Linearity to Midposition Undo Digital Horizontal Linearity to MidpositionAstigmatism to Midposition DIG HOR Linearity MID Undo All Settings to Midposition All Settings to MidpositionUndo Astigmatism to Midposition Common Settings Common SettingsDynamic Astigmatism Dynamic Astigmatism Green Common Settings Gamma CorrectionsCRT Run In Cycle CRT RUN in Cycle CRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Menu Position Flyback Turnover PointFlyback Turnover Point 12C Diagnostics Voltage DiagnosticsI2C Diagnostics Decoder Projector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage Diagnostics Programmable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Adjustment Blocks and Source Numbers Adjustment Blocks Memory BlocksSource Numbers Block Header Example of Block Header Source input Source number Block header a RS-232 Codes Page CEILING/FLOOR Configuration TD = Throw Distance Factors Dimensions Bottom ViewSide View Front View Specifications Page RUMA-009450 rev