Runco DTV-1200 SERVICE MODE

SERVICE MODE

PROJECTOR SET-UP

MEMORYMANAGEMENT

COMMON SETTINGS

I2C DIAGNOSTICS

VOLTAGE DIAGNOSTICS

PROJECTOR DIAGNOSTICS

Select with or

then <ENTER>

<EXIT> to return

53

SERVICE MODE

Start Up

1. Push the cursor key or to select to SERVICE (menu 1).

2. Press ENTER to select.

The service menu will be displayed (menu 2). Some items in the Service mode are password protected

(when the password function is active). Enter your password to continue. All other password protected items

are now also available if you stay in the adjustment mode.

Service Mode

ADJUSTMENTMODE

Select a path from below:

RANDOM ACCESS

INSTALLATION

SERVICE source 1

Select with or

then <ENTER>

<EXIT> to return

menu 1 menu 2

Overview Flowchart

SERVICEMODE

PROJECTOR SETUP

PROJECTOR DIAGNOSTICS

MEMORYMANAGEMENT

COMMON SETTINGS

VOLTAGE DIAGNOSTICS

I2C DIAGNOSTICS

IDENTIFICATION

TOTALRUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUD RATE

PROJECTOR WARM UP

POWER UPMODE

COMMONADDRESS

COPYA BLOCK

DELETE ABLOCK

DELETE ALLBLOCKS

SETTO MIDPOSITION

DYNAMIC ANTIGMATISM

CRTRUN IN CYCLE

GAMMACORRECTION

MEMORYBANKS: ON

MENU POSITION: STANDARD

CRTDRIVE MODE

FLYBACK TURNOVER POINT

Contents

Main Page TABLE OF CONTENTS Page Page SAFETY INSTRUCTIONS ! Safety Instructions ! Page Page Page Limited Warranty LIMITED WARRANTY Page CONNECTIONS Power Connection to Projector Source Connections RGB Source to Input 3 RGB Source with Composite Sync to Input 4/5 RGB Source with Tri-level Sync to Input 4/5 Component Source to Input 4/5 RS-232 Connection GETTING STARTED Remote Control & Local Keypad Page ! Remote Commands to the Projector Pointing the Remote to the reflective screen Point the front of the Remote to the screen surface. Remote or Ceiling Screen Projector Address Page Page START UP OF THE ADJUSTMENT MODE Adjustment Mode MAIN MENU Main Menu Image Control Color Adjust Format Select Page Eye-Q Control Eye-Q Touch Up Eye-Q Auto Converge Function Keys Service Menus ENTERING THE SERVICE MENUS Service Menus Page RANDOM ACCESS ADJUSTMENT MODE Random Access Adjustment Mode Overview Flowchart Selecting Setup Pattern Internal Cross Hatch Pattern Random Access Adjustment Mode Selection Menu Picture Tuning Color Balance Sync Fast/Slow Adjustments Peaking Clamp Tuning Geometry Adjustments Horizontal Phase Adjustments Raster Shift Adjustments Left-Right (East-West) Adjustments Page Left Side Correction Top-Bottom (North-South) Adjustments Page Horizontal Size Adjustments Vertical Linearity Adjustments Vertical Size Adjustments Blanking Adjustments Page Convergence Adjustments Focusing Page Color Select SERVICE MODE Service Mode menu 1 menu 2 Overview Flowchart Projector Setup Identification RUNCO DTV-1200 Run Time Change Password Change Projector Address Change Baud Rate Projector Warm Up Warm Up On/Off Warm Up Frequency Projector Warm Up Time Power Up Mode Common Address Memory Management Copy a Block Deletion of Blocks Deleting Block by Block Deletion of All Blocks Set to Midposition R & B Covergence Mid Undo R & B Convergence Mid Green Convergence Mid Undo Green Convergence Mid Focus to Midposition Undo Focus to Midposition East-West to Midposition Undo East-West to Midposition North-South Settings to Midposition Undo North-South Settings to Midposition Digital Vertical Linearity to Midposition Undo Digital Vertical Linearity to Midposition Digital Horizontal Linearity to Midposition Undo Digital Horizontal Linearity to Midposition Astigmatism to Midposition Undo Astigmatism to Midposition All Settings to Midposition Undo All Settings to Midposition Common Settings Dynamic Astigmatism Page Gamma Corrections CRT Run In Cycle CRT Drive Mode Memory Banks Flyback Turnover Point Menu Position 12C Diagnostics Voltage Diagnostics Projector Diagnostics PROGRAMMABLE FUNCTION KEYS Programmable Function Keys MESSAGES, WARNINGS AND FAILURES Page ADJUSTMENT BLOCKS AND SOURCE NUMBERS 90-99 Adjustment Blocks (Memory Blocks) Source Numbers 90-99 Page RS-232 CODES Page CEILING/FLOOR CONFIGURATION DIMENSIONS SPECIFICATIONS