Common Settings, Dynamic Astigmatism | Runco DTV-1200 specification

Common Settings

What can be done?

Within the common settings menu, the following items can be set up or executed:

-Dynamic Astigmatism

-Gamma Correction

-CRT run in cycle

-CRT Drive mode

-Memory banks : on/off

-Flyback turnover point

-Menu Position : standard/middle

How to select?

1.Push the cursor key or to highlight 'Common Settings' (menu 1).

2.Press ENTER to select. The common settings menu will be displayed (menu 2)

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

I2C DIAGNOSTICS

VOLTAGE DIAGNOSTICS

PROJECTOR DIAGNOSTICS

Select with or then <ENTER>

<EXIT> to return

menu 1

COMMON SETTINGS

DYNAMIC ASTIGMATISM GAMMA CORRECTIONS CRT RUN IN CYCLE CRT DRIVE MODE MEMORYBANKS : ON FLYBACK TURNOVER POINT MENU POSITION : STANDARD

Select with or then <ENTER>

<EXIT> to return

menu 2

Dynamic Astigmatism

What can be done?

The spot shape adjustments correct the spot shape in 25 different areas on the screen for the three colors separately. The spot shape is adjusted according to the axial axises and the diagonal axises when using the cursor keys on the Remote. These adjustments have to be done on a dot pattern (external source or genlocked pattern).

Spot shapes

before dynamic

astigmatism correction

	Diagonal
	astigmatism correction
	(use the and	Spot shapes
	arrow key)	Spot shapes
	arrow key)	after dynamic
		after dynamic
		astigmatism correction

Axial

astigmatism correction

(use the and

arrow key)

70

Image 72

Runco DTV-1200 owner manual Common Settings, Dynamic Astigmatism

Contents

DTV-1200 Page Table of Contents Page Page Safety Instructions Safety Instructions Mains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugPage Page Limited Warranty Effective Warranty Date Power Connection to Projector Connections Source Connections Source No Projector Input Remote Button No RGB Source to Input RGB Source with Composite Sync to Input 4/5Input Select Input RGB Source with Tri-level Sync to Input 4/5 Component Source to Input 4/5RS-232 Connection Remote Control & Local Keypad Getting Started Audio controls not used Stationary Image Warning Projector Warm UP Remote Commands to the Projector Front of projector Projector Address Input Selection via the Remote Brightness Control Contrast ControlColor Saturation Control Not used on the DTV-1200 Start UP of the Adjustment Mode Adjustment Mode Main Menu Main Menu Color Adjust Image Control Format Select Compose Eye-Q Control Eye-Q Touch Up Eye-Q Auto Converge Adjustment Mode Main Menu Entering the Service Menus Service Menus Enter Password Random Access Adjustment Mode Random Access Adjustment ModeRandom Access Selecting Setup Pattern Internal Cross Hatch Pattern VGA Random Access Adjustment Mode Selection Menu Picture TuningRandom Access Adjustment Mode Picture Tuning Gain adjustment affects the brightest areas of the image Picture Tuning Color BalanceColor Balance Color Balance Sync Fast/Slow Adjustments Picture TuningColor Balance Clamp Tuning Piture TuningPeaking Peaking Geometry Adjustments Horizontal Phase AdjustmentsRandom Access Adjustment Mode Geometry Raster Shift Adjustments Phase Left-Right East-West Adjustments Forbidden AreaProjected Raster CRT Faceplate Border Phosphor Coarse Shift LEFT-RIGHT Left Side Correction What can be done?Start up Left Side Correction Top-Bottom North-South Adjustments GeometryTOP-BOTTOM N-S TOP-BOTTOM N-S TOP-BOTTOM TOP BOW TOP Keystone Bottom BOW Bottom Keystone Horizontal Size Adjustments Size Vertical Linearity Adjustments Linearity V SizeLinearity Vertical Size Adjustments Blanking AdjustmentsBlanking Blanking Correct by pushing the cursor keys up or down Convergence Adjustments Converge AdjustmentConvergence Convergence Focusing FocusingFocusing Midpoint TOP BottomLeft Color Select RightBlue on Source Color Select Service Mode Service ModeRandom Access Installation Service Mode Projector Setup Software version ConfigurationIdentification Text ON/OFF Run Time Projector SET-UPIdentification RUN Time Change Password Change PasswordPassword Change Password Change Projector Address Change Baud RateProjector SET-UP Projector Address Baud Rate Projector Warm Up Warm Up On/OffProjector Warm UP Warm Up Frequency Projector Warm Up TimeProjector Warm UP Power Up Mode Common Address Copy Mode Memory ManagementCopy a Block Memory Management Delete Mode Deletion of BlocksDeleting Block by Block Deletion of All Blocks Set to Midposition Covergence MidDelete ALL Blocks SET to Midposition Undo R & B Convergence Mid Convergence MIDSET to Midposition Green Convergence MID Undo Green Convergence Mid Focus to MidpositionUndo Focus to Midposition North-South Settings to Midposition East-West to MidpositionUndo East-West to Midposition To Midposition Undo North-South Settings to Midposition Digital Vertical Linearity to MidpositionUndo Digital Vertical Linearity to Midposition DIG Vert Linearity MID Digital Horizontal Linearity to Midposition Undo Digital Horizontal Linearity to MidpositionAstigmatism to Midposition DIG HOR Linearity MID All Settings to Midposition Undo All Settings to MidpositionUndo Astigmatism to Midposition Common Settings Common SettingsDynamic Astigmatism Dynamic Astigmatism Green Common Settings Gamma CorrectionsCRT Run In Cycle CRT RUN in Cycle CRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Menu PositionFlyback Turnover Point 12C Diagnostics Voltage DiagnosticsI2C Diagnostics Decoder Projector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage Diagnostics Phase Raster Shift Programmable Function KeysProgrammable Function Keys MESSAGES, Warnings and Failures Failure Adjustment Blocks and Source Numbers Adjustment Blocks Memory BlocksSource Numbers Block Header Example of Block Header Source input Source number Block header a RS-232 Codes Page CEILING/FLOOR Configuration TD = Throw Distance Factors Dimensions Bottom ViewSide View Front View Specifications Page RUMA-009450 rev