Eye-Q Auto Converge | Runco DTV-1200 guide

How to start up the EYE-Q Touch Up?

1Push the cursor keys or to select 'EYE-Q Touch Up' (menu 1).

2Press ENTER to activate the touch up function.

The process starts and when successfully completed, the projector will return to image display of the current source.

EYE-Q CONTROL

EYE-Q Touch Up

EYE-Q Auto Converge

Select with or then <ENTER> <EXIT> to return

menu 1

Eye-Q Auto Converge

What can be done?

The autoconvergence on the current source will be carried out automatically, starting from the existing settings. By projecting alternately red and blue lines, 25 convergence areas are aligned onto the green pattern.

How to start up the EYE-Q Auto Converge?

1Push the cursor keys or to select 'EYE-Q Auto Converge' (menu 1).

2Press ENTER to activate the autoconvergence function.

The process starts and when successfully completed, the projector will return to image display of the current source.

EYE-Q CONTROL

EYE-Q Touch Up

EYE-Q Auto Converge

Select with or then <ENTER> <EXIT> to return

menu 1

27

Image 29

Runco DTV-1200 owner manual Eye-Q Auto Converge

Contents

DTV-1200 Page Table of Contents Page Page Safety Instructions Safety Instructions Power cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugPage Page Limited Warranty Effective Warranty Date Connections Power Connection to Projector Source No Projector Input Remote Button No Source Connections Input Select Input RGB Source to InputRGB Source with Composite Sync to Input 4/5 RS-232 Connection RGB Source with Tri-level Sync to Input 4/5Component Source to Input 4/5 Getting Started Remote Control & Local Keypad Audio controls not used Projector Warm UP Stationary Image Warning Front of projector Remote Commands to the Projector Projector Address Input Selection via the Remote Color Saturation Control Not used on the DTV-1200 Brightness ControlContrast Control Adjustment Mode Start UP of the Adjustment Mode Main Menu Main Menu Image Control Color Adjust Format Select Compose Eye-Q Touch Up Eye-Q Control Eye-Q Auto Converge Main Menu Adjustment Mode Service Menus Entering the Service Menus Enter Password Random Access Random Access Adjustment ModeRandom Access Adjustment Mode Selecting Setup Pattern VGA Internal Cross Hatch Pattern Picture Tuning Random Access Adjustment Mode Selection MenuRandom Access Adjustment Mode Picture Tuning Picture Tuning Color Balance Gain adjustment affects the brightest areas of the imageColor Balance Color Balance Color Balance Sync Fast/Slow AdjustmentsPicture Tuning Piture Tuning Clamp TuningPeaking Peaking Horizontal Phase Adjustments Geometry AdjustmentsRandom Access Adjustment Mode Geometry Phase Raster Shift Adjustments Forbidden Area Left-Right East-West AdjustmentsProjected Raster CRT Faceplate Border Phosphor Coarse Shift LEFT-RIGHT What can be done? Left Side CorrectionStart up Left Side Correction Geometry Top-Bottom North-South AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-S TOP BOW TOP Keystone Bottom BOW Bottom Keystone TOP-BOTTOM Size Horizontal Size Adjustments Linearity Vertical Linearity AdjustmentsLinearity V Size Blanking Adjustments Vertical Size AdjustmentsBlanking Blanking Correct by pushing the cursor keys up or down Converge Adjustment Convergence AdjustmentsConvergence Convergence Focusing FocusingFocusing Midpoint Left TOPBottom Right Color SelectBlue on Source Color Select Service Mode Service ModeRandom Access Installation Service Mode Software version Configuration Projector SetupIdentification Text ON/OFF Projector SET-UP Run TimeIdentification RUN Time Change Password Change PasswordPassword Change Password Change Baud Rate Change Projector AddressProjector SET-UP Projector Address Baud Rate Projector Warm UP Projector Warm UpWarm Up On/Off Projector Warm UP Warm Up FrequencyProjector Warm Up Time Common Address Power Up Mode Memory Management Copy ModeCopy a Block Memory Management Deletion of Blocks Delete ModeDeleting Block by Block Deletion of All Blocks Covergence Mid Set to MidpositionDelete ALL Blocks SET to Midposition Convergence MID Undo R & B Convergence MidSET to Midposition Green Convergence MID Undo Focus to Midposition Undo Green Convergence MidFocus to Midposition East-West to Midposition North-South Settings to MidpositionUndo East-West to Midposition To Midposition Digital Vertical Linearity to Midposition Undo North-South Settings to MidpositionUndo Digital Vertical Linearity to Midposition DIG Vert Linearity MID Undo Digital Horizontal Linearity to Midposition Digital Horizontal Linearity to MidpositionAstigmatism to Midposition DIG HOR Linearity MID Undo Astigmatism to Midposition All Settings to MidpositionUndo All Settings to Midposition Dynamic Astigmatism Common SettingsCommon Settings Green Dynamic Astigmatism Gamma Corrections Common SettingsCRT Run In Cycle CRT RUN in Cycle CRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Flyback Turnover PointMenu Position Voltage Diagnostics 12C DiagnosticsI2C Diagnostics Decoder Projector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage Diagnostics Programmable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Adjustment Blocks Memory Blocks Adjustment Blocks and Source NumbersSource Numbers Block Header Example of Block Header Source input Source number Block header a RS-232 Codes Page TD = Throw Distance Factors CEILING/FLOOR Configuration Bottom View DimensionsSide View Front View Specifications Page RUMA-009450 rev