Runco DTV-1200 RANDOM ACCESS ADJUSTMENT MODE

RANDOM ACCESS ADJUSTMENT MODE

Starting Up

Push the cursor keys up or down to highlight "RANDOM ACCESS" and then press ENTER.

Some items in the Random access mode are password protected (when the password function is enabled).

Enter your password to continue. All other password protected items are now also available if you stay in the

adjustment mode.

Random Access Adjustment Mode

ADJUSTMENTMODE

Select a path from below:

EYE-Q

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

Source 1

Select with or

then <ENTER>

<EXIT> to return

Overview Flowchart

RANDOMACCESS

ADJUSTMENTMODE

SETUPPATTERN

SELECTION

PICTURETUNING

GEOMETRY

COLORBALANCE

SYNC

PEAKING

CLAMPTUNING

H PHASE

RASTER SHIFT

LEFT-RIGHT(E-W)

LEFTSIDE CORRECTIONS

SIZE

VER LINEARITY

BLANKING

V CENTERLINE BOW

V CENTERLINE SKEW

SIDE BOW

SIDE KEYSTONE

SEAGULLCORRECTION

LEFTBOW

LEFTKEYSTONE

H CENTERLINE BOW

H CENTERLINE SKEW

TOPKEYSTONE

TOPBOW

BOTTOM KEYSTONE

SEAGULLCORRECTION

RIGHT

LEFT

BOTTOM

TOP

TOP-BOTTOM (N-S)

Contents

Main Page TABLE OF CONTENTS Page Page SAFETY INSTRUCTIONS ! Safety Instructions ! Page Page Page Limited Warranty LIMITED WARRANTY Page CONNECTIONS Power Connection to Projector Source Connections RGB Source to Input 3 RGB Source with Composite Sync to Input 4/5 RGB Source with Tri-level Sync to Input 4/5 Component Source to Input 4/5 RS-232 Connection GETTING STARTED Remote Control & Local Keypad Page ! Remote Commands to the Projector Pointing the Remote to the reflective screen Point the front of the Remote to the screen surface. Remote or Ceiling Screen Projector Address Page Page START UP OF THE ADJUSTMENT MODE Adjustment Mode MAIN MENU Main Menu Image Control Color Adjust Format Select Page Eye-Q Control Eye-Q Touch Up Eye-Q Auto Converge Function Keys Service Menus ENTERING THE SERVICE MENUS Service Menus Page RANDOM ACCESS ADJUSTMENT MODE Random Access Adjustment Mode Overview Flowchart Selecting Setup Pattern Internal Cross Hatch Pattern Random Access Adjustment Mode Selection Menu Picture Tuning Color Balance Sync Fast/Slow Adjustments Peaking Clamp Tuning Geometry Adjustments Horizontal Phase Adjustments Raster Shift Adjustments Left-Right (East-West) Adjustments Page Left Side Correction Top-Bottom (North-South) Adjustments Page Horizontal Size Adjustments Vertical Linearity Adjustments Vertical Size Adjustments Blanking Adjustments Page Convergence Adjustments Focusing Page Color Select SERVICE MODE Service Mode menu 1 menu 2 Overview Flowchart Projector Setup Identification RUNCO DTV-1200 Run Time Change Password Change Projector Address Change Baud Rate Projector Warm Up Warm Up On/Off Warm Up Frequency Projector Warm Up Time Power Up Mode Common Address Memory Management Copy a Block Deletion of Blocks Deleting Block by Block Deletion of All Blocks Set to Midposition R & B Covergence Mid Undo R & B Convergence Mid Green Convergence Mid Undo Green Convergence Mid Focus to Midposition Undo Focus to Midposition East-West to Midposition Undo East-West to Midposition North-South Settings to Midposition Undo North-South Settings to Midposition Digital Vertical Linearity to Midposition Undo Digital Vertical Linearity to Midposition Digital Horizontal Linearity to Midposition Undo Digital Horizontal Linearity to Midposition Astigmatism to Midposition Undo Astigmatism to Midposition All Settings to Midposition Undo All Settings to Midposition Common Settings Dynamic Astigmatism Page Gamma Corrections CRT Run In Cycle CRT Drive Mode Memory Banks Flyback Turnover Point Menu Position 12C Diagnostics Voltage Diagnostics Projector Diagnostics PROGRAMMABLE FUNCTION KEYS Programmable Function Keys MESSAGES, WARNINGS AND FAILURES Page ADJUSTMENT BLOCKS AND SOURCE NUMBERS 90-99 Adjustment Blocks (Memory Blocks) Source Numbers 90-99 Page RS-232 CODES Page CEILING/FLOOR CONFIGURATION DIMENSIONS SPECIFICATIONS