Projector Setup, Identification, Text ON/OFF | Runco DTV-1200

Projector Setup

What can be done?

Within the projector set-up menu, the following items can be consultated or set to the desired setting:

-Identification

-Total run time

-Change password

-Change projector address

-Change baud rate

-Projector warm up

-Power up mode

-Common address

Start up the Projector Set-Up

To select Projector Set-Up:

1.Push the cursor key or to highlight Projector Set Up (menu 1).

2.Press ENTER to display the Projector set up menu (menu 2).

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

I2C DIAGNOSTICS

VOLTAGE DIAGNOSTICS

PROJECTOR DIAGNOSTICS

Select with or then <ENTER>

<EXIT> to return

menu 1

PROJECTOR SET-UP

IDENTIFICATION

RUN TIME

CHANGE PASSWORD

CHANGE PROJECTOR ADDRESS

CHANGE BAUD RATE

PROJECTOR WARM UP

POWER UP MODE: operating

COMMON ADDRESS: 0 Select with or then <ENTER>

<EXIT> to return

menu 2

Identification

What can be seen?

The 'Identification' screen gives information concerning:

-Projector address. To change the address of your projector, contact a qualified service technician.

-Software version.

-Configuration.

Possible installations:

*Front-ceiling

*Front-table

*Rear-ceiling

*Rear-table

-Baud Rate: transfer speed for communication with an external control system. The baud rate of the projector must be the same as the baud rate of the connected control system.

-Text ON/OFF

Indicates in operational mode if the bar scale and number indicator will be displayed and if warnings and failures will be displayed.

ON : displayed

OFF : not displayed

The status can be changed by pressing the 'TEXT' key once on the Remote.

-Serial no.: indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.

-Projector Level: from 0 to 6. The higher the level the more software options installed. Contact your vendor for more information.

54

Image 56

Runco DTV-1200 owner manual Projector Setup, Identification, Software version Configuration, Text ON/OFF, Projector SET-UP

Contents

DTV-1200 Page Table of Contents Page Page Safety Instructions Safety Instructions Mains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugPage Page Limited Warranty Effective Warranty Date Power Connection to Projector Connections Source Connections Source No Projector Input Remote Button No Input Select Input RGB Source to InputRGB Source with Composite Sync to Input 4/5 RS-232 Connection RGB Source with Tri-level Sync to Input 4/5Component Source to Input 4/5 Remote Control & Local Keypad Getting Started Audio controls not used Stationary Image Warning Projector Warm UP Remote Commands to the Projector Front of projector Projector Address Input Selection via the Remote Color Saturation Control Not used on the DTV-1200 Brightness ControlContrast Control Start UP of the Adjustment Mode Adjustment Mode Main Menu Main Menu Color Adjust Image Control Format Select Compose Eye-Q Control Eye-Q Touch Up Eye-Q Auto Converge Adjustment Mode Main Menu Entering the Service Menus Service Menus Enter Password Random Access Random Access Adjustment ModeRandom Access Adjustment Mode Selecting Setup Pattern Internal Cross Hatch Pattern VGA Random Access Adjustment Mode Selection Menu Picture TuningRandom Access Adjustment Mode Picture Tuning Gain adjustment affects the brightest areas of the image Picture Tuning Color BalanceColor Balance Color Balance Color Balance Sync Fast/Slow AdjustmentsPicture Tuning Clamp Tuning Piture TuningPeaking Peaking Geometry Adjustments Horizontal Phase AdjustmentsRandom Access Adjustment Mode Geometry Raster Shift Adjustments Phase Left-Right East-West Adjustments Forbidden AreaProjected Raster CRT Faceplate Border Phosphor Coarse Shift LEFT-RIGHT Left Side Correction What can be done?Start up Left Side Correction Top-Bottom North-South Adjustments GeometryTOP-BOTTOM N-S TOP-BOTTOM N-S TOP-BOTTOM TOP BOW TOP Keystone Bottom BOW Bottom Keystone Horizontal Size Adjustments Size Linearity Vertical Linearity AdjustmentsLinearity V Size Vertical Size Adjustments Blanking AdjustmentsBlanking Blanking Correct by pushing the cursor keys up or down Convergence Adjustments Converge AdjustmentConvergence Convergence Focusing FocusingFocusing Midpoint Left TOPBottom Color Select RightBlue on Source Color Select Service Mode Service ModeRandom Access Installation Service Mode Projector Setup Software version ConfigurationIdentification Text ON/OFF Run Time Projector SET-UPIdentification RUN Time Change Password Change PasswordPassword Change Password Change Projector Address Change Baud RateProjector SET-UP Projector Address Baud Rate Projector Warm UP Projector Warm UpWarm Up On/Off Projector Warm UP Warm Up FrequencyProjector Warm Up Time Power Up Mode Common Address Copy Mode Memory ManagementCopy a Block Memory Management Delete Mode Deletion of BlocksDeleting Block by Block Deletion of All Blocks Set to Midposition Covergence MidDelete ALL Blocks SET to Midposition Undo R & B Convergence Mid Convergence MIDSET to Midposition Green Convergence MID Undo Focus to Midposition Undo Green Convergence MidFocus to Midposition North-South Settings to Midposition East-West to MidpositionUndo East-West to Midposition To Midposition Undo North-South Settings to Midposition Digital Vertical Linearity to MidpositionUndo Digital Vertical Linearity to Midposition DIG Vert Linearity MID Digital Horizontal Linearity to Midposition Undo Digital Horizontal Linearity to MidpositionAstigmatism to Midposition DIG HOR Linearity MID Undo Astigmatism to Midposition All Settings to MidpositionUndo All Settings to Midposition Dynamic Astigmatism Common SettingsCommon Settings Dynamic Astigmatism Green Common Settings Gamma CorrectionsCRT Run In Cycle CRT RUN in Cycle CRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Flyback Turnover PointMenu Position 12C Diagnostics Voltage DiagnosticsI2C Diagnostics Decoder Projector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage Diagnostics Programmable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Adjustment Blocks and Source Numbers Adjustment Blocks Memory BlocksSource Numbers Block Header Example of Block Header Source input Source number Block header a RS-232 Codes Page CEILING/FLOOR Configuration TD = Throw Distance Factors Dimensions Bottom ViewSide View Front View Specifications Page RUMA-009450 rev