Runco DTV-1200 instruction

Contrast +:	02.00.00.28.00.00.00.00.28
Contrast -:	02.00.00.29.00.00.00.00.29
Brightness +:	02.00.00.2A.00.00.00.00.2A
Brightness -:	02.00.00.2B.00.00.00.00.2B
Color +:	02.00.00.2C.00.00.00.00.2C
Color -:	02.00.00.2D.00.00.00.00.2D
Tint +:	02.00.00.2E.00.00.00.00.2E
Tint -:	02.00.00.2F.00.00.00.00.2F
Sharpness +:	02.00.00.36.00.00.00.00.36
Sharpness -:	02.00.00.37.00.00.00.00.37

All commands are in hex and will be entered differently with each control system.

For example:
Phast = Power On:	$02,$00,$00,$51,$00,$00,$00,$01,$5C
AMX= Power On:	h02,h00,h00,h51,h00,h00,h00,h01,h5C

Crestron = Power On: \x02\x00\x00\x51\x00\x00\x00\x01\x5C

Pin Configuration: 9-pin din female.

Pin 2 - RXD

Pin 3 - TXD

Pin 5 - Ground

Straight thru wire configuration

Page 86

Image 86

Contents

DTV-1200 Page Table of Contents Page Page Safety Instructions Safety Instructions Mains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugPage Page Limited Warranty Effective Warranty Date Power Connection to Projector Connections Source Connections Source No Projector Input Remote Button No Input Select Input RGB Source to InputRGB Source with Composite Sync to Input 4/5 RS-232 Connection RGB Source with Tri-level Sync to Input 4/5Component Source to Input 4/5 Remote Control & Local Keypad Getting Started Audio controls not used Stationary Image Warning Projector Warm UP Remote Commands to the Projector Front of projector Projector Address Input Selection via the Remote Color Saturation Control Not used on the DTV-1200 Brightness ControlContrast Control Start UP of the Adjustment Mode Adjustment Mode Main Menu Main Menu Color Adjust Image Control Format Select Compose Eye-Q Control Eye-Q Touch Up Eye-Q Auto Converge Adjustment Mode Main Menu Entering the Service Menus Service Menus Enter Password Random Access Random Access Adjustment ModeRandom Access Adjustment Mode Selecting Setup Pattern Internal Cross Hatch Pattern VGA Random Access Adjustment Mode Random Access Adjustment Mode Selection MenuPicture Tuning Picture Tuning Color Balance Gain adjustment affects the brightest areas of the imagePicture Tuning Color Balance Color Balance Color Balance Sync Fast/Slow AdjustmentsPicture Tuning Peaking Clamp TuningPiture Tuning Peaking Random Access Adjustment Mode Geometry AdjustmentsHorizontal Phase Adjustments Geometry Raster Shift Adjustments Phase Projected Raster CRT Faceplate Border Phosphor Left-Right East-West AdjustmentsForbidden Area Coarse Shift LEFT-RIGHT Start up Left Side CorrectionWhat can be done? Left Side Correction TOP-BOTTOM N-S Top-Bottom North-South AdjustmentsGeometry TOP-BOTTOM N-S TOP-BOTTOM TOP BOW TOP Keystone Bottom BOW Bottom Keystone Horizontal Size Adjustments Size Linearity Vertical Linearity AdjustmentsLinearity V Size Blanking Vertical Size AdjustmentsBlanking Adjustments Blanking Correct by pushing the cursor keys up or down Convergence Convergence AdjustmentsConverge Adjustment Convergence Focusing FocusingFocusing Midpoint Left TOPBottom Blue on Source Color SelectRight Color Select Random Access Installation Service ModeService Mode Service Mode Identification Projector SetupSoftware version Configuration Text ON/OFF Identification Run TimeProjector SET-UP RUN Time Password Change PasswordChange Password Change Password Projector SET-UP Projector Address Change Projector AddressChange Baud Rate Baud Rate Projector Warm UP Projector Warm UpWarm Up On/Off Projector Warm UP Warm Up FrequencyProjector Warm Up Time Power Up Mode Common Address Copy a Block Copy ModeMemory Management Memory Management Deleting Block by Block Delete ModeDeletion of Blocks Deletion of All Blocks Delete ALL Blocks Set to MidpositionCovergence Mid SET to Midposition SET to Midposition Undo R & B Convergence MidConvergence MID Green Convergence MID Undo Focus to Midposition Undo Green Convergence MidFocus to Midposition Undo East-West to Midposition North-South Settings to MidpositionEast-West to Midposition To Midposition Undo Digital Vertical Linearity to Midposition Undo North-South Settings to MidpositionDigital Vertical Linearity to Midposition DIG Vert Linearity MID Astigmatism to Midposition Digital Horizontal Linearity to MidpositionUndo Digital Horizontal Linearity to Midposition DIG HOR Linearity MID Undo Astigmatism to Midposition All Settings to MidpositionUndo All Settings to Midposition Dynamic Astigmatism Common SettingsCommon Settings Dynamic Astigmatism Green CRT Run In Cycle Common SettingsGamma Corrections CRT RUN in Cycle CRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Flyback Turnover PointMenu Position I2C Diagnostics 12C DiagnosticsVoltage Diagnostics Decoder Projector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage Diagnostics Programmable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Source Numbers Adjustment Blocks and Source NumbersAdjustment Blocks Memory Blocks Block Header Example of Block Header Source input Source number Block header a RS-232 Codes Page CEILING/FLOOR Configuration TD = Throw Distance Factors Side View DimensionsBottom View Front View Specifications Page RUMA-009450 rev

Runco DTV-1200 owner manual

Models: DTV-1200