Vertical Size Adjustments, Blanking Adjustments | Runco DTV-1200

Vertical Size Adjustments

What can be done?

To adjust the vertical picture size.

Start up
1.	Push the cursor key			or			to highlight 'V Size' (menu 1).

2.	Press ENTER to activate (menu 2).
3.	Push the cursor key			or			until the correct image height is obtained. (image 1).

Note:

-If the internal # pattern was selected, this pattern remains on the screen.

-If the genlocked pattern was selected, the external source will be displayed. A bar scale and a numeric indicator help to gauge the size adjustment.

menu 1

GEOMETRY

HPHASE RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

VLINEARITY V SIZE

BLANKING

Select with or then <ENTER> <EXIT> to return

Blanking Adjustments

What can be done?

Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A 0% on the bar scale indicates no blanking. The following blanking adjustment are available: Top, Bottom, left and right blanking.

Start Up

To start up the Blanking adjustments, follow the next procedure :

1.Push the cursor key or to highlight Blanking (menu 1).

2.Press ENTER to display the blanking menu (menu 2).

-If the internal # pattern was selected, this pattern remains on the screen.

-If the genlocked pattern was selected, the external source will be displayed.

GEOMETRY

HPHASE RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with or then <ENTER> <EXIT> to return

menu 1

BLANKING

TOP

BOTTOM

LEFT

RIGHT

Select with or then <ENTER>

<EXIT> to return

menu 2

47

Image 49

Runco DTV-1200 owner manual Vertical Size Adjustments, Blanking Adjustments

Contents

DTV-1200 Page Table of Contents Page Page Safety Instructions Safety Instructions Power cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugPage Page Limited Warranty Effective Warranty Date Connections Power Connection to Projector Source No Projector Input Remote Button No Source Connections RGB Source with Composite Sync to Input 4/5 RGB Source to InputInput Select Input Component Source to Input 4/5 RGB Source with Tri-level Sync to Input 4/5RS-232 Connection Getting Started Remote Control & Local Keypad Audio controls not used Projector Warm UP Stationary Image Warning Front of projector Remote Commands to the Projector Projector Address Input Selection via the Remote Contrast Control Brightness ControlColor Saturation Control Not used on the DTV-1200 Adjustment Mode Start UP of the Adjustment Mode Main Menu Main Menu Image Control Color Adjust Format Select Compose Eye-Q Touch Up Eye-Q Control Eye-Q Auto Converge Main Menu Adjustment Mode Service Menus Entering the Service Menus Enter Password Random Access Adjustment Mode Random Access Adjustment ModeRandom Access Selecting Setup Pattern VGA Internal Cross Hatch Pattern Picture Tuning Random Access Adjustment Mode Selection MenuRandom Access Adjustment Mode Picture Tuning Picture Tuning Color Balance Gain adjustment affects the brightest areas of the imageColor Balance Color Balance Picture Tuning Sync Fast/Slow AdjustmentsColor Balance Piture Tuning Clamp TuningPeaking Peaking Horizontal Phase Adjustments Geometry AdjustmentsRandom Access Adjustment Mode Geometry Phase Raster Shift Adjustments Forbidden Area Left-Right East-West AdjustmentsProjected Raster CRT Faceplate Border Phosphor Coarse Shift LEFT-RIGHT What can be done? Left Side CorrectionStart up Left Side Correction Geometry Top-Bottom North-South AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-S TOP BOW TOP Keystone Bottom BOW Bottom Keystone TOP-BOTTOM Size Horizontal Size Adjustments Linearity V Size Vertical Linearity AdjustmentsLinearity Blanking Adjustments Vertical Size AdjustmentsBlanking Blanking Correct by pushing the cursor keys up or down Converge Adjustment Convergence AdjustmentsConvergence Convergence Focusing FocusingFocusing Midpoint Bottom TOPLeft Right Color SelectBlue on Source Color Select Service Mode Service ModeRandom Access Installation Service Mode Software version Configuration Projector SetupIdentification Text ON/OFF Projector SET-UP Run TimeIdentification RUN Time Change Password Change PasswordPassword Change Password Change Baud Rate Change Projector AddressProjector SET-UP Projector Address Baud Rate Warm Up On/Off Projector Warm UpProjector Warm UP Projector Warm Up Time Warm Up FrequencyProjector Warm UP Common Address Power Up Mode Memory Management Copy ModeCopy a Block Memory Management Deletion of Blocks Delete ModeDeleting Block by Block Deletion of All Blocks Covergence Mid Set to MidpositionDelete ALL Blocks SET to Midposition Convergence MID Undo R & B Convergence MidSET to Midposition Green Convergence MID Focus to Midposition Undo Green Convergence MidUndo Focus to Midposition East-West to Midposition North-South Settings to MidpositionUndo East-West to Midposition To Midposition Digital Vertical Linearity to Midposition Undo North-South Settings to MidpositionUndo Digital Vertical Linearity to Midposition DIG Vert Linearity MID Undo Digital Horizontal Linearity to Midposition Digital Horizontal Linearity to MidpositionAstigmatism to Midposition DIG HOR Linearity MID Undo All Settings to Midposition All Settings to MidpositionUndo Astigmatism to Midposition Common Settings Common SettingsDynamic Astigmatism Green Dynamic Astigmatism Gamma Corrections Common SettingsCRT Run In Cycle CRT RUN in Cycle CRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Menu Position Flyback Turnover PointFlyback Turnover Point Voltage Diagnostics 12C DiagnosticsI2C Diagnostics Decoder Projector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage Diagnostics Programmable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Adjustment Blocks Memory Blocks Adjustment Blocks and Source NumbersSource Numbers Block Header Example of Block Header Source input Source number Block header a RS-232 Codes Page TD = Throw Distance Factors CEILING/FLOOR Configuration Bottom View DimensionsSide View Front View Specifications Page RUMA-009450 rev