Input Selection via the Remote | Runco DTV-1200 instruction

Input selection modes

Source No.	Projector Input	Remote Button No.

3	RGB	3

4/5	RGB (HV, S.O.G)	4 or 5

4/5	Component Video	6

4/5	RGB with Tri level sync	7

4/5	Component Video with
	Tri-level sync	8

Input Selection via the Remote.

With the digit buttons, it is possible to select one of the above input modes.

When the source is selected

When a valid and available source is selected, there will be information displayed on the screen about that source. This information includes:

-Source number

-Horizontal frequency

-Vertical frequency

Source 02

Fh= 63 kHz

Fv= 60 Hz

When the entry is a non valid source number, a warning appears on the screen: 'input not available'.

WARNING

Input not

available

When a valid source number is selected, the projector will display this source or it will wait on the selected source number until the source becomes available. A message 'source not available' will be displayed for a short time.

WARNING

Source not

available

When a Video or S-Video source is selected and no decoder is installed, the projector displays the folllowing message: 'Option not installed'.

WARNING

Option not

installed!

19

Image 21

Runco DTV-1200 owner manual Input Selection via the Remote

Contents

DTV-1200 Page Table of Contents Page Page Safety Instructions Safety Instructions Power cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugPage Page Limited Warranty Effective Warranty Date Connections Power Connection to Projector Source No Projector Input Remote Button No Source Connections RGB Source to Input RGB Source with Composite Sync to Input 4/5Input Select Input RGB Source with Tri-level Sync to Input 4/5 Component Source to Input 4/5RS-232 Connection Getting Started Remote Control & Local Keypad Audio controls not used Projector Warm UP Stationary Image Warning Front of projector Remote Commands to the Projector Projector Address Input Selection via the Remote Brightness Control Contrast ControlColor Saturation Control Not used on the DTV-1200 Adjustment Mode Start UP of the Adjustment Mode Main Menu Main Menu Image Control Color Adjust Format Select Compose Eye-Q Touch Up Eye-Q Control Eye-Q Auto Converge Main Menu Adjustment Mode Service Menus Entering the Service Menus Enter Password Random Access Adjustment Mode Random Access Adjustment ModeRandom Access Selecting Setup Pattern VGA Internal Cross Hatch Pattern Picture Tuning Random Access Adjustment Mode Selection MenuRandom Access Adjustment Mode Picture Tuning Picture Tuning Color Balance Gain adjustment affects the brightest areas of the imageColor Balance Color Balance Sync Fast/Slow Adjustments Picture TuningColor Balance Piture Tuning Clamp TuningPeaking Peaking Horizontal Phase Adjustments Geometry AdjustmentsRandom Access Adjustment Mode Geometry Phase Raster Shift Adjustments Forbidden Area Left-Right East-West AdjustmentsProjected Raster CRT Faceplate Border Phosphor Coarse Shift LEFT-RIGHT What can be done? Left Side CorrectionStart up Left Side Correction Geometry Top-Bottom North-South AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-S TOP BOW TOP Keystone Bottom BOW Bottom Keystone TOP-BOTTOM Size Horizontal Size Adjustments Vertical Linearity Adjustments Linearity V SizeLinearity Blanking Adjustments Vertical Size AdjustmentsBlanking Blanking Correct by pushing the cursor keys up or down Converge Adjustment Convergence AdjustmentsConvergence Convergence Focusing FocusingFocusing Midpoint TOP BottomLeft Right Color SelectBlue on Source Color Select Service Mode Service ModeRandom Access Installation Service Mode Software version Configuration Projector SetupIdentification Text ON/OFF Projector SET-UP Run TimeIdentification RUN Time Change Password Change PasswordPassword Change Password Change Baud Rate Change Projector AddressProjector SET-UP Projector Address Baud Rate Projector Warm Up Warm Up On/OffProjector Warm UP Warm Up Frequency Projector Warm Up TimeProjector Warm UP Common Address Power Up Mode Memory Management Copy ModeCopy a Block Memory Management Deletion of Blocks Delete ModeDeleting Block by Block Deletion of All Blocks Covergence Mid Set to MidpositionDelete ALL Blocks SET to Midposition Convergence MID Undo R & B Convergence MidSET to Midposition Green Convergence MID Undo Green Convergence Mid Focus to MidpositionUndo Focus to Midposition East-West to Midposition North-South Settings to MidpositionUndo East-West to Midposition To Midposition Digital Vertical Linearity to Midposition Undo North-South Settings to MidpositionUndo Digital Vertical Linearity to Midposition DIG Vert Linearity MID Undo Digital Horizontal Linearity to Midposition Digital Horizontal Linearity to MidpositionAstigmatism to Midposition DIG HOR Linearity MID All Settings to Midposition Undo All Settings to MidpositionUndo Astigmatism to Midposition Common Settings Common SettingsDynamic Astigmatism Green Dynamic Astigmatism Gamma Corrections Common SettingsCRT Run In Cycle CRT RUN in Cycle CRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Menu PositionFlyback Turnover Point Voltage Diagnostics 12C DiagnosticsI2C Diagnostics Decoder Projector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage Diagnostics Phase Raster Shift Programmable Function KeysProgrammable Function Keys MESSAGES, Warnings and Failures Failure Adjustment Blocks Memory Blocks Adjustment Blocks and Source NumbersSource Numbers Block Header Example of Block Header Source input Source number Block header a RS-232 Codes Page TD = Throw Distance Factors CEILING/FLOOR Configuration Bottom View DimensionsSide View Front View Specifications Page RUMA-009450 rev