Wireless network setup (CLX-3185FW/CLX-3185WK only)_ 8
administrator to get the static IP address.
•For the DHCP method
If the IP address assignment method is DHCP, check if
DHCP is shown in the Wireless Network Setting Confirm
window. However, if it shows Static, click Change TCP/IP
to change the assignment method to Receive IP address
automatically (DHCP).
•For the Static method
If the IP address assignment method is Static, check if
Static is shown in the Wireless Network Setting Confirm
window. However, if it shows DHCP, click Change TCP/IP
to enter the IP address and other network configuration
values for the machine.
Example)
If computer’s network information is as below:
-IP address: 169.254.133.42
-Subnet Mask: 255.255.0.0
Machine’s network information should be as below:
-IP address: 169.254.133. 43 (Use computer’s IP address,
with changed last three digits.)
-Subnet Mask: 255.255.0.0 (Use the computer’s subnet
mask.)
-Gateway: 169.254.133.1 (Change the last three digits from
IP address of your machine to 1.)
17.The wireless network is connecting according to the network
configuration.
18.When the wireless network setting is completed, disconnect the USB
cable between the computer and machine. Click Next.
19.The Installation process is being executed.
20.The Fax Queue Creator window appears during the installation
process.
•For CLX-3185WK, click Cancel to go to the next step.
•For CLX-3185FW, select your machine name from the Printer
Name list and click Create. When the confirmation window
appears, click OK.
21.Click Continue on the Read Me window.
22.After the installation is finished, click Restart.
Setting a wireless network with network cable
Your machine is a network compatible machine. To enable your machine to
work with your network, you will need to perform some configuration
procedures.
Refer to your network administrator, or the person that set up your
wireless network for information about your network configuration.

Preparing items

Ensure you have next items ready.
•Access point
•Network-connected computer
•Software CD that provided with your machine
•Wireless network printer (your machine)
•Network cable

Setting IP address

First, you have to set up an IP address for network printing and
managements. In most cases, a new IP address will be automatically
assigned by a DHCP (Dynamic Host Configuration Protocol) server located
on the network.
In a few situations, the IP address must be set manually. This is called a
static IP and is often required in a corporate Intranets for security reasons.
•DHCP IP assignment: Connect your machine to the network, and wait a
few minutes for the DHCP server to assign an IP address to the
machine. Then, print the Network Configuration Report as explained
above. If the report shows that the IP address has changed, the
assignment was successful. You will see the new IP address in the
report. (See "Printing a network configuration report" on page 2.)
•Static IP assignment: Use SetIP program to change the IP address
from your computer.
In an office environment, we recommend that you contact a network
administrator to set this address for you.

IP setting using SetIP Program (Windows)

This program is for manually setting the network IP address of your
machine using its MAC address to communicate with the machine. A
MAC address is the hardware serial number of the network interface and
can be found in the Network Configuration Report.
For using SetIP program, disable the computer firewall before continuing
by performing the following:
1.Open Start > All programs > Control Panel.
2.Double-click Security Center.
3.Click Windows Firewall.
4.Disable the firewall.
Installing the program
1.Insert the software CD provided with your machine. When the driver
CD runs automatically, close that window.
2.Start Windows Explorer and open the X drive. (X represents your
CD-ROM drive.)
3.Double-click Application > SetIP.
4.Double-click Setup.exe to install this program.
5.Click OK. If necessary, select a language from the drop-down list.
6.Follow the instructions in the window and complete the installation.
Starting the program
1.Connect your machine to the network with a network cable.
2.Turned on the machine.
3.From the Windows Start menu, select All Programs > Samsung
Printers > SetIP > SetIP.
4.Click on the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.