Interrupt Status Register F241h R/W, Rsti | Samsung KFN4G16Q2A

MuxOneNAND2G(KFM2G16Q2A-DEBx)	FLASH MEMORY
MuxOneNAND4G(KFN4G16Q2A-DEBx)

2.8.22 Interrupt Status Register F241h (R/W)

This Read/Write register shows status of the MuxOneNAND interrupts.

In DDP, INT register will not be written if DBS, DFS is not set.

F241h, defaults = 8080h after Cold Reset; 8010h after Warm/Hot Reset

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
INT			Reserved(0000000)					RI	WI	EI	RSTI		Reserved(0000)

Interrupt (INT)

This is the master interrupt bit. The INT bit is wired directly to the INT pin on the chip. Upon writing '0' to the INT bit, the INT pin goes low if INTpol is high and goes high if INTpol is low.

INT Interrupt [15]

	Status	Conditions	Default State		Valid	Interrupt
	Status	Conditions	Cold	Warm/hot	State	Function
			Cold	Warm/hot	State	Function
			1	1	0	off

		One or more of RI, WI, RSTI and EI is set to ‘1’, or			0→1	Pending
	sets itself to ‘1’	0065h, 0023h, 0071h, 002Ah, 0027h and 002Ch			0→1	Pending
		commands are completed.

		’0’ is written to this bit,
	clears to ‘0’	Cold/Warm/Hot reset is being performed, or			1→0	off
	clears to ‘0’	command is written to Command Register in INT			1→0	off
		command is written to Command Register in INT
		auto mode

Read Interrupt (RI)

This is the Read interrupt bit.

RI Interrupt [7]

	Status	Conditions	Default State		Valid	Interrupt
	Status	Conditions	Cold	Warm/hot	State	Function
			Cold	Warm/hot	State	Function
			1	0	0	off

		At the completion of an Load Operation			0→1	Pending
	sets itself to ‘1’	(0000h, 000Eh, 000Ch, 000Ah, 0013h,			0→1	Pending
		Load Data into Buffer, or boot is done)

		’0’ is written to this bit,
	clears to ‘0’	Cold/Warm/Hot reset is being performed, or			1→0	off
	clears to ‘0’	command is written to Command Register in INT			1→0	off
		command is written to Command Register in INT
		auto mode

- 75 -

Image 75

Samsung KFN4G16Q2A, KFM2G16Q2A warranty Interrupt Status Register F241h R/W, Rsti

Contents

KFM2G16Q2A KFN4G16Q2A Revision No History Initial issue Jul Revision No NOR Flash Product Type SelectorPKG Nand Architectural Benefits Ordering Information System Hardware Product FeaturesDevice Architecture Device Performance General Overview Error Correction Code Detailed Product DescriptionDefinitions 1 2Gb Product KFM2G16Q2A Pin Configuration 2 4Gb Product KFN4G16Q2A Pin Description OTP Block DiagramMemory Array Organization Internal Nand Array Memory Organization Internal Memory Array Organization Internal Memory Array Information Area Block Sector Total Size 1KB+32B 2KB+64B External BufferRAM MemoryInternal Nand Array Memory External BufferRAM Memory Organization BootRAM DataRAM0 DataRAM1 Main area data BootRAMBootRAM DataRAM Block Block Address Sector Size Memory Map Block Block Address 0083h 0000h~00FFh 128KB Block163 0080h 0000h~00FFh 128KB Block1600081h 0000h~00FFh 128KB Block161 0082h 0000h~00FFh 128KB Block162 00E2h 0000h~00FFh 128KB Block195 00C3h Block192 00C0h 0000h~00FFh 128KB00E0h 0000h~00FFh 128KB Block193 00C1h 00E1h 0000h~00FFh 128KB Block194 00C2h 0103h 0000h~00FFh 128KB Block291 0123h 0100h 0000h~00FFh 128KB Block288 0120h0101h 0000h~00FFh 128KB Block289 0121h 0102h 0000h~00FFh 128KB Block290 0122h 0143h 0000h~00FFh 128KB Block355 0163h 0140h 0000h~00FFh 128KB Block352 0160h0141h 0000h~00FFh 128KB Block353 0161h 0142h 0000h~00FFh 128KB Block354 0162h 0000h~00FFh 128KB Block387 0183h Block419 Block384 0180h 0000h~00FFh 128KB Block4160000h~00FFh 128KB Block385 0181h Block417 0000h~00FFh 128KB Block386 0182h Block418 01E1h 0000h~00FFh 128KB 01C0h 0000h~00FFh 128KB01E0h 0000h~00FFh 128KB 01C1h 0000h~00FFh 128KB 0203h 0000h~00FFh 128KB Block547 0223h 0200h 0000h~00FFh 128KB Block544 0220h0201h 0000h~00FFh 128KB Block545 0221h 0202h 0000h~00FFh 128KB Block546 0222h 0243h 0000h~00FFh 128KB 0240h 0000h~00FFh 128KB Block608 0260h0241h 0000h~00FFh 128KB Block609 0261h 0242h 0000h~00FFh 128KB Block610 0262h 0283h 0000h~00FFh 128KB Block675 0280h 0000h~00FFh 128KB Block6720281h 0000h~00FFh 128KB Block673 0282h 0000h~00FFh 128KB Block674 02E2h 0000h~00FFh 128KB Block707 02C3h Block704 02C0h 0000h~00FFh 128KB02E0h 0000h~00FFh 128KB Block705 02C1h 02E1h 0000h~00FFh 128KB Block706 02C2h 0303h 0000h~00FFh 128KB Block803 0323h 0300h 0000h~00FFh 128KB Block800 0320h0301h 0000h~00FFh 128KB Block801 0321h 0302h 0000h~00FFh 128KB Block802 0322h 0343h 0000h~00FFh 128KB Block867 0363h 0340h 0000h~00FFh 128KB Block864 0360h0341h 0000h~00FFh 128KB Block865 0361h 0342h 0000h~00FFh 128KB Block866 0362h 0000h~00FFh 128KB Block899 0383h Block931 Block896 0380h 0000h~00FFh 128KB Block9280000h~00FFh 128KB Block897 0381h Block929 0000h~00FFh 128KB Block898 0382h Block930 03E1h 0000h~00FFh 128KB 03C0h 0000h~00FFh 128KB03E0h 0000h~00FFh 128KB 03C1h 0000h~00FFh 128KB 0403h 0000h~00FFh 128KB Block1059 0423h 0400h 0000h~00FFh 128KB Block1056 0420h0401h 0000h~00FFh 128KB Block1057 0421h 0402h 0000h~00FFh 128KB Block1058 0422h 0461h 0000h~00FFh 128KB 0440h 0000h~00FFh 128KB0460h 0000h~00FFh 128KB 0441h 0000h~00FFh 128KB 0483h 0000h~00FFh 128KB 0480h 0000h~00FFh 128KB0481h 0000h~00FFh 128KB 0482h 0000h~00FFh 128KB 04C3h 0000h~00FFh 128KB Block1251 04E3h 04C0h 0000h~00FFh 128KB Block1248 04E0h04C1h 0000h~00FFh 128KB Block1249 04E1h 04C2h 0000h~00FFh 128KB Block1250 04E2h 0503h 0000h~00FFh 128KB Block1315 0523h 0500h 0000h~00FFh 128KB Block1312 0520h0501h 0000h~00FFh 128KB Block1313 0521h 0502h 0000h~00FFh 128KB Block1314 0522h 0543h 0000h~00FFh 128KB Block1379 0563h 0540h 0000h~00FFh 128KB Block1376 0560h0541h 0000h~00FFh 128KB Block1377 0561h 0542h 0000h~00FFh 128KB Block1378 0562h 0583h 0000h~00FFh 128KB Block1443 0580h 0000h~00FFh 128KB Block14400581h 0000h~00FFh 128KB Block1441 0582h 0000h~00FFh 128KB Block1442 05C3h 0000h~00FFh 128KB Block1507 05E3h 05C0h 0000h~00FFh 128KB Block1504 05E0h05C1h 0000h~00FFh 128KB Block1505 05E1h 05C2h 0000h~00FFh 128KB Block1506 05E2h 0603h 0000h~00FFh 128KB Block1571 0623h 0600h 0000h~00FFh 128KB Block1568 0620h0601h 0000h~00FFh 128KB Block1569 0621h 0602h 0000h~00FFh 128KB Block1570 0622h 0643h 0000h~00FFh 128KB Block1635 0663h 0640h 0000h~00FFh 128KB Block1632 0660h0641h 0000h~00FFh 128KB Block1633 0661h 0642h 0000h~00FFh 128KB Block1634 0662h 0683h 0000h~00FFh 128KB Block1699 0680h 0000h~00FFh 128KB Block16960681h 0000h~00FFh 128KB Block1697 0682h 0000h~00FFh 128KB Block1698 06C3h 0000h~00FFh 128KB Block1763 06E3h 06C0h 0000h~00FFh 128KB Block1760 06E0h06C1h 0000h~00FFh 128KB Block1761 06E1h 06C2h 0000h~00FFh 128KB Block1762 06E2h 0703h 0000h~00FFh 128KB Block1827 0723h 0700h 0000h~00FFh 128KB Block1824 0720h0701h 0000h~00FFh 128KB Block1825 0721h 0702h 0000h~00FFh 128KB Block1826 0722h 0743h 0000h~00FFh 128KB Block1891 0763h 0740h 0000h~00FFh 128KB Block1888 0760h0741h 0000h~00FFh 128KB Block1889 0761h 0742h 0000h~00FFh 128KB Block1890 0762h 0000h~00FFh 128KB Block1923 0783h Block1955 Block1920 0780h 0000h~00FFh 128KB Block19520000h~00FFh 128KB Block1921 0781h Block1953 0000h~00FFh 128KB Block1922 0782h Block1954 07C3h 0000h~00FFh 128KB Block2019 07E3h 07C0h 0000h~00FFh 128KB Block2016 07E0h07C1h 0000h~00FFh 128KB Block2017 07E1h 07C2h 0000h~00FFh 128KB Block2018 07E2h Word Byte Lnternal Memory Spare Area Assignment Division Address Size Usage Description External Memory BufferRAM Address Map External Memory Map Detail Information 0800h~08FFh512B 0900h~09FFh512B DataM8048h~804Fh16B Buf External Memory Spare Area Assignment 8028h 10050h 8029h 10052h Managed by Internal ECC logic Managed by Internal ECC logic DataS 8023h 10046hECC Code for Main area data 3rd 8026h 1004Ch 8027h 1004Eh Managed by Internal ECC logic Buf Word Byte8048h 8049h Registers Register Address MapAddress Name Host Description Manufacturer ID Register F000h R DeviceID150 Device ID DefaultDevice ID Register F001h R Device Identification Description This Register is reserved for internal use F003h, default = 0800h DataBufSizeVersion ID Register F002h Data Buffer Size Register F003h R Boot Buffer Size Register F004h R Number of Buffers Register F005h RTechnology Register F006h R Start Address2 Register F101h R/W Start Address1 Register F100h R/W Fcpa FCSA1 Start Address3 Register F102h R/WStart Address4 Register F103h R/W Fcba Start Address8 Register F107h R/W Start Address5 Register F104h R/WStart Address6 Register F105h Start Address7 Register F106h Start Buffer Register F200h R/W BSABSC Operation Command Register F220h R/WAcceptable CMD Two Methods to Clear Interrupt Register in Command Input Write command into INT will automaticallyInterrupt Register Brwl System Configuration 1 Register F221h R, R/W INT Polarity INTpol Information6 Burst Length BLBurst Length BL Information119 Definition Description RDY Polarity RDYpol Information7 Iobe Bwps Write Mode WMWrite Mode Information1 Definition MRSMode register Setting Description Mode Description Controller Status Register F240h R System Configuration 2 Register F222h Program = ready defaultError Error Information10 Sector/Page Load/Program/CopyBack Rstb OtplOtpbl Time Out to Plane1 CurrentPlane2 Previous Plane2 Current Controller Status Register Output Modes Flash Memory Interrupt Status Register F241h R/W INTRsti Rsti Interrupt Status Conditions Default State Valid Default State ValidEI Interrupt Status Conditions Default State Valid Reset Interrupt Rsti SBA Start Block Address Register F24Ch R/WEnd Block Address Register F24Dh Nand Flash Write Protection Status Register F24Eh R ECC Information150 Error Status ERm, ERs ECC StatusECC Status Register FF00h R ERm3 ERs3 ERm2 ERs2 ERm1 ERs1 ERm0 ERs01 Reserved0000000000 ECClogSector1 ECCposIO1 Reserved0000 ECCposWord0 ECCposIO0Reserved0000000000 ECClogSector0 ECCposIO0 Reserved0000 ECCposWord1 ECCposIO1 Reserved0000000000 ECClogSector3 ECCposIO3 Reserved0000 ECCposWord2 ECCposIO2Reserved0000000000 ECClogSector2 ECCposIO2 Reserved0000 ECCposWord3 ECCposIO3 ECC Log Sector ECClogSector Information Error Position Command Based Operation Reset MuxOneNAND Add BP1 Data 00F0hAdd Data 00E0h 0000h3 Read Identification Data XXXXh4 0090h Identification Data Description Address Data Out Reset MuxOneNAND CommandLoad MuxOneNAND Command Read Identification Data Command Device Bus Operation Operation ADQ0~15CLK AVD Reset Mode Operation Nand Flash Core Reset Mode Operation Cold Reset Mode OperationWarm Reset Mode Operation Hot Reset Mode Operation Nand Array Write Protection States BootRAM Write Protection OperationWrite Protection Operation Nand Flash Array Write Protection Operation Unlocked Nand Array Write Protection State Unlocked Unlock Command SequenceUnlocked All Block Unlock Command Sequence Locked Lock Command Sequence Locked-tight Nand Array Write Protection State Nand Flash Array Write Protection State DiagramLocked-tight Lock-Tight Command Sequence Power On Add F24Ch DQ=SBA Data Protection Operation Flow DiagramAdd F101h DQ=DBS Add F100h DQ=DFS Add F241h DQ15=INT All Block Unlock Flow DiagramAdd F241h DQ=0000h DQ=0027h Host reads data from DataRAM Read completed Data Protection During Power Down OperationLoad Operation YES Asynchronous Read Mode Operation RM=0, WM=0 Synchronous Read Mode Operation RM=1, WM=XRead Operation 2.2 4-, 8-, 16-, 32-Word Linear Burst Read Operation Continuous Linear Burst Read Operation Output Disable Mode Operation Programmable Burst Read Latency OperationHandshaking Operation Cache Read Operation RM=X, WM=X Cache-Read flow chart is on the following Map out Write ‘Cache Read’ Command Add F220h DQ=000EhWrite ’DFS*, FBA’ of Flash Add F100h DQ=DFS, FBA END Setting Read Read data from DataRAM Cont 1st DQ0 Address A/DQ15 Setting INT 2nd4th Status Command Host reads 1st Cache Read Diagram Synchronous Burst Block Read OperationRM=1, WM=X See Timing Diagram 6.3 Terminating Synchronous Burst Block Read Synchronous Burst Block Read Boundary 102 Four Clock Burst Read Latency default condition 103 Synchronous Burst Block Read Operation Flow Chart Synchronous WriteRM=1, WM=1 See Timing Diagram 6.8, 6.9 Addressing for program operation Program Operation Add F100h DQ=DFS*’, FBA Program Operation Flow DiagramProgram Lock Error Program Error ADD DP DQ=Data-in 107 11.1 2X Program Operation 108 2X Program Operation Flow DiagramAdd F100h DQ=DFS*, FBA Add F220h DQ=007Dh 109 11.2 2X Cache Program Operation 110 DBS, DFS is for DDP 111 11.3 2X Interleave Cache Program Operation 112 2X Interleave Cache Program Operation Flow Diagram StartLast 2 Plane PGM For a chip? For a chip 113 Copy-Back Program Operation Flash Memory 115 Copy-Back Program Operation with Random Data Input Block Erase Operation Erase Operation Locked Blocks Multi-Block Erase Operation Add F240h DQ10=0 Multi Block Erase/ Multi Block Erase Verify Read Flow ChartMulti-Block Erase Verify Read Operation Add F220h DQ=0095h Erase Suspend / Erase Resume Operation Erase Suspend During a Block Erase Operation119 OTP Operation 1st Block OTP Area Structure OTP Block Area Structure 122 OTP Block Load Operation Programming the OTP Area OTP Block Program Operation OTP Block Program Operation Flow Chart Write ‘DFS, FBA’ of Flash Add F100h DQ=DFS, FBA3OTPL=0? YES OTP Block Lock Operation Locking the OTPOTP Lock Operation Steps 126 Add F241h DQ15=INT Do Cold resetAutomatically Updated Write ’DFS, FBA’ of Flash Add F100h DQ=DFS, FBA3 14.4 1st Block OTP Lock Operation Locking the 1st Block OTP1st Block OTP Lock Operation Steps 128 OTP and 1st Block OTP Lock Operation Locking the OTP and 1st Block OTPOTP and 1st Block OTP simultaneous Lock Operation Steps 130 Data Load Dual OperationsRead-While-Load Operation Write-While-Program Operation AVD INT ADQDB0 DB1 133 Progress Data Loading Don’t Care 16 DQ6 Toggle BitStatus DQ15~DQ7 DQ6 DQ5~DQ0 ECC Bypass Operation ECC Operation Invalid Block Identification Table Operation Invalid Block Operation Invalid Block Table Creation Flow Chart Start Invalid Block Replacement Operation Block Replacement Operation Sequence 1st 1th NthBlock B Absolute Maximum Ratings Operating ConditionsKFM2G16Q2A Test Conditions DC Characteristics DDP Valid Block CharacteristicsAC Test Conditions Device Capacitance AC Characteristics for Synchronous Burst Read 66MHz 83MHz UnitMax Min KFN4G16Q2A AC Characteristics for Asynchronous ReadSee Timing Diagrams 6.5, 6.6, 6.22 See Timing Diagrams 6.18, 6.19 Parameter Symbol Min Max 66MHz 83MHz Unit Min AC Characteristics for Asynchronous WriteAC Characteristics for Burst Write Operation Min Max AC Characteristics for Load/Program/Erase Performance AC Characteristics for INT Auto ModeAC Characteristics for Synchronous Burst Block Read RDY 8-Word Linear Burst Read Mode with Wrap AroundContinuous Linear Burst Read Mode with Wrap Around CLK 147 148 Synchronous Burst Block Read Timing Burst block read 149 Asynchronous Read VA Transition After AVD Low See AC Characteristics Table DQ0 DQ15Asynchronous Read VA Transition Before Low 151 Asynchronous WriteValid WD Hi-Z 152 8-Word Linear Burst Write ModeBurst Write Operation followed by Burst Read ≈D7 153 Start Initial Burst Write Operation Bit See AC Characteristics Tables 5.5, 5.7Load Command Sequence last two cycles Read Data Load Operation Timing 155 Program Operation Timing 13 2X Program Operation Timing Ongoing StatusADQ0~ADQ15 . . A1 14 2X Cache Program Operation TimingMuxOneNAND2GKFM2G16Q2A MuxOneNAND4GKFN4G16Q2A ADQ15 15 2X InterleaveCache Program ADQ0~ Erase Command Sequence Read Status Data Block Erase Operation Timing159 Default Cold Reset TimingBootcode copy done Bootcode copy INT bit Warm Reset TimingSee AC Characteristics Tables CE, OE Idle Hot Reset TimingADQi BPNote 00F0h Or F220h Or 00F3h Nand Flash Core Reset Timing Data Protection Timing During Power Down163 Status RD Hi-Z RDY164 INT auto mode Write command into Command Register INT will automatically165 Methods of Determining Interrupt Status INT Type Mono INT Type DDP166 Synchronous Mode Using the INT Pin Asynchronous Mode Using the INT PinINT Pin to a Host General Purpose I/O Handshaking Mode Non-Handshaking Mode Polling the Interrupt Register Status Bit168 INT pol = ‘High’ Default Determining Rp Value DDP, QDP onlyRpohm Vss KFN4G16Q2A @ Vcc = 1.8V, Ta = 25C , CL = 30pF INT pol = ‘Low’Vcc or Vccq ~50k ohm Ready Boot Loaders in MuxOneNAND Description Boot SequenceBoot Loaders in MuxOneNAND Boot Sequence BL1 BL2 NBL3 NBL1 NBL2BL2 BL1 2G product KFM2G16Q2A 4G product KFN4G16Q2A173