Menu Structure of the F6 button | Samsung SSA-S3010/EXP specification

other information

Menu Structure of the [F6] button

You can set Output for Accessible levels for READER #1 and #2 ID, READER #1 and #2 ID Error Output, READER #1 and #2 Time Schedule Error Output, READER #1 and #2 Antipassback Error Output.

F6 button

RD1 ID OK LV1

RD1 ID OK LV2

RD1 ID OK LV3

RD1 ID OK LV4

RD1 ID ERROR

RD1 T/S ERROR

RD1 APB ERROR

RD2 ID OK LV1

RD2 ID OK LV2

RD2 ID OK LV3

RD2 ID OK LV4

RD2 ID ERROR

RD2 T/S ERROR

RD2 APB ERROR

72_ other information

Page 72

Image 72

Samsung SSA-S3010/EXP manual Menu Structure of the F6 button

Contents

Standalone Biometric Access Controller Please visit our website Safety information Safety information Important Safety Instructions Safety InformationThis device may not cause harmful interference, Contents Contents Event Memory Setup Wiegand Output SetupVoice Volume Setup Input Type Setup Features Product introduction External I/O Pins Forced Door Open AlarmDoor Open Timeout Alarm Duress Alarm WHAT’S Included Quick Guide CD Manual AT a Glance Front PanelLCD Communication status indicator Pin Connector Preliminary connector for extensionRear Panel LED PIN Connector Pins Signal Cable ColorCable Color Scheme TCP/IP RJ45 Connector Cable Selection Installing the Wall Mount Follow the instructions below to install the wall mount Connecting the Termination Resistor and Diode Bypass Diode Connection EARTH-GROUNDING the Communication Cables Connection Input Connection Output Connection External Reader Connection External Reader Connection Communication Line Connection RS-232 Communication Port Connection RS-485 Communication Port Connection Standalone RS-485 Communication Port Connection Multiple UnitsMax m Please follow the steps below TCP/IP Communication Port Connection Connect all RS-485 ports of the product in parallel Initializing the system using the Initialize switch System Initialization in Master ModeInitialization Initializing the System To Access the Master Mode Registering a Master IDTo register a master card To register a master card along with your ﬁngerprint To register a master card PIN00/00 Lift PUT Your Finger Name Display To register a master card PIN along with your ﬁngerprintNot USE User Count Setup Language Setup DATE/TIME Setup Communication Address SetupSET DATE/TIME Comm Addr SET Baud Rate Setup Factory DefaultsDefault SET Baud Rate Reader mode setup Reader #1 ModeReader #2 Mode READER#1 Mode ID only JID+F/PP/W € USE If set, you can get access using the keypad input RD#1 KEY Input not USE Reader Mode SetupReader #1 KEY Input Reader #2 KEY Input Dual Fingerprint Mode Dual F/P Mode Jnot USE Dual F/P Mode USE Adaptive Mode Identification ModeAdaptive Mode not USE Jnot USE Adaptive Mode USE Mode Setup Identification Jnot USE Registering ID in Quick Mode User managementTo register ID To register ID along with ﬁngerprint Registering the ID To register the ID cardPW TA TB C RD MA MB LV FP User Management ID Registered To register the ID card along with your ﬁngerprint To register the PIN numberTo select PIN SSA-S30x1 Numeric letters in 4 ~ 8 or 10 digits To Delete ID To register the PIN number along with your ﬁngerprintEnter PIN Screen Viewing the ID List ID List To Check the Number of Registered Fingerprints ALL ID ClearFP REG. Count Duress Mode Duress Mode Not USE Duress Password Enter Duress P/WTo delete all registered master IDs Master ID CLR Door Open Alarm Time Setup ARM/DISARMOpen ALR Time User Management ARM/DISARM SET TWO MEN Operation Mode To move to the TWO MEN Mode itemTo Check the Number of Events To select USE or not USE, and press ENT . J not USE To Remove ALL Events To Remove the Time Schedule Time setup Door Contact Sensor SetupExit Button Output Exit Button Auxiliary Input #1 Setup Auxiliary Input #2 SetupTime Setup AUX INPUT#1 Tamper Alarm Output Setup CUT OFF Output SetupTamper Alarm CUT OFF Alarm Duress Mode Output Setup ARM/DISARM Output Setup Door Open Timeout Setup RD1 ID OK LV1 Output Setup for Level 2 IDs Accessing Reader #1 Output Setup for Level 3 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 Error Output Setup Reader #1 ID Error Output SetupReader #1 Time Schedule Error Output Setup Reader #1 Antipassback Error Output Setup Output Setup for Level IDS Accessing Reader #2 RD2 ID OK LV2 Reader #2 Error Output Setup Output Setup for Level 4 IDs Accessing Reader #2Reader #2 ID Error Output Setup 12.RD2 ID Error Reader #2 Time Schedule Error Output Setup Reader #2 Antipassback Error Output Setup13.RD2 T/S Error Time Setup 14.RD2 APB Error Advanced setup Time Unit SetupOutput Time SCHEDULE+ID Time Unit Unit 1SEC Unit 0.1SEC Antipassback Mode Time Schedule SetupAPB Mode Not USE ALL Clear Use the 4 Buttons to specify the interval, day Holiday Setup Holiday Code Setup Holiday CodeCode 01 Code 10 Reader Mode Time Schedule Reader #1 Mode Time Schedule Reader #2 Mode Time ScheduleRD1 Mode I T/S RD2 Mode I T/S Output Time Schedule Setup Voice Message Time ScheduleVoice I T/S T/S Code ‘00’ means no Time Schedules are to be applied Input Time Schedule Setup Input CUT OFF Check SetupCUT OFF SET Additional features Event Memory SetupID Display Wiegand Output Setup Voice Volume SetupVoice Volume Wiegand Output not USE Not USE  The default setting for One Time Read is not USE ONE Time Read Not USE Jnot USE Additional FeaturesONE Time Read Version Check Input Test Output Test Last Update LCD TestKeypad Test Press ANY KEY RAM TESTING… Reader TestMemory Test Reader Test SCANNING… Communication Test Fingerprint Module Version CheckFailed If the test has succeeded If the test has failed Input Type Setup Input TypeO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Other information Menu Structure Menu Structure of the F3 button F3 buttonMenu Structure of the F4 button F4 button Menu Structure of the F5 button F5 buttonOther Information Menu Structure of the F6 button F6 button Menu Structure of the F7 button Menu Structure of the F8 button Menu Structure of the F9 button F9 buttonMenu Structure of the F10 button F10 button Default Settings Output Settings for Input SourcesDuress Alarm TTL#1 TTL#2 Output Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Buzzer keeps beeping Communication betweenController and the Host PC fails Software Product Specifications Product speciﬁcations Correct disposal of batteries in this product