Baud Rate Setup, Factory Defaults | Samsung SSA-S3010/EXP guide

BAUD RATE SETUP

This product supports 9600, 19200, 38400, and 57600 bps, and it is set to 57600 bps by default.

An improper speed setting can cause a communication error so ensure that you specify the same speed in the same network.

1.Press the F1 SETUP MENU button.

2.	Use the buttons	4	and	6	to move to the BAUD RATE item and press
	ENT .
3.	Use the buttons	4	and	6	to select a serial communication speed.

• 9600

19200

38400

57600

4. When done, press ENT to save your settings.

M If you encounter a problem with the communication, check the followings ﬁrst.

-Check the communication addresses for this product and the host PC (software).

-Check the baud rate settings of each of the host PC and this product.

-Check the communication port and cable.

-Check the host PC for the port settings.

8.BAUD RATE 57600

8. BAUD RATE

J19200

8.BAUD RATE 19200

INITIALIZATION

FACTORY DEFAULTS

All menu settings will return to the factory default. (The memory is not deleted.)

1.Press the F8 SETUP MENU button.

2.	Use the buttons	4	and 6 to move to the DEFAULT SET item and press	6. DEFAULT SET
	ENT .
3.	Press the button	1	to restore the menu settings to the default.

• To cancel initialization, press the button 0 .

6. DEFAULT SET

1:YES, 0:NO

English _ 29

Image 29

Samsung SSA-S3010/EXP manual Baud Rate Setup, Factory Defaults, Default SET

Contents

Please visit our website Standalone Biometric Access Controller Safety information Safety information This device may not cause harmful interference, Important Safety InstructionsSafety Information Contents Contents Wiegand Output Setup Event Memory SetupVoice Volume Setup Input Type Setup Product introduction Features Forced Door Open Alarm External I/O PinsDoor Open Timeout Alarm Duress Alarm Quick Guide CD Manual WHAT’S Included LCD AT a GlanceFront Panel Pin Connector Preliminary connector for extension Communication status indicatorRear Panel LED Cable Color Scheme PIN ConnectorPins Signal Cable Color Cable Selection TCP/IP RJ45 Connector Follow the instructions below to install the wall mount Installing the Wall Mount Bypass Diode Connection Connecting the Termination Resistor and Diode EARTH-GROUNDING the Communication Cables Input Connection Connection Output Connection External Reader Connection External Reader Connection RS-232 Communication Port Connection Communication Line Connection RS-485 Communication Port Connection Multiple Units RS-485 Communication Port Connection StandaloneMax m Please follow the steps below Connect all RS-485 ports of the product in parallel TCP/IP Communication Port Connection System Initialization in Master Mode Initializing the system using the Initialize switchInitialization Initializing the System To register a master card To Access the Master ModeRegistering a Master ID To register a master card PIN To register a master card along with your ﬁngerprint00/00 Lift PUT Your Finger Not USE Name DisplayTo register a master card PIN along with your ﬁngerprint Language Setup User Count Setup Communication Address Setup DATE/TIME SetupSET DATE/TIME Comm Addr SET Factory Defaults Baud Rate SetupDefault SET Baud Rate Reader #1 Mode Reader mode setupReader #2 Mode READER#1 Mode ID only JID+F/PP/W RD#1 KEY Input not USE Reader Mode Setup € USE If set, you can get access using the keypad inputReader #1 KEY Input Reader #2 KEY Input Dual F/P Mode Jnot USE Dual F/P Mode USE Dual Fingerprint Mode Identification Mode Adaptive ModeAdaptive Mode not USE Jnot USE Adaptive Mode USE Mode Setup Identification Jnot USE User management Registering ID in Quick ModeTo register ID To register ID along with ﬁngerprint PW TA TB C RD MA MB LV FP User Management ID Registered Registering the IDTo register the ID card To register the PIN number To register the ID card along with your ﬁngerprintTo select PIN SSA-S30x1 Numeric letters in 4 ~ 8 or 10 digits To register the PIN number along with your ﬁngerprint To Delete IDEnter PIN Screen ID List Viewing the ID List FP REG. Count To Check the Number of Registered FingerprintsALL ID Clear Duress Mode Not USE Duress Password Enter Duress P/W Duress ModeTo delete all registered master IDs Master ID CLR ARM/DISARM Door Open Alarm Time SetupOpen ALR Time User Management ARM/DISARM SET To move to the TWO MEN Mode item TWO MEN Operation ModeTo Check the Number of Events To select USE or not USE, and press ENT . J not USE To Remove the Time Schedule To Remove ALL Events Door Contact Sensor Setup Time setupExit Button Output Exit Button Auxiliary Input #2 Setup Auxiliary Input #1 SetupTime Setup AUX INPUT#1 CUT OFF Output Setup Tamper Alarm Output SetupTamper Alarm CUT OFF Alarm ARM/DISARM Output Setup Duress Mode Output Setup RD1 ID OK LV1 Door Open Timeout Setup Output Setup for Level 4 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 3 IDs Accessing Reader #1 Reader #1 ID Error Output Setup Reader #1 Error Output SetupReader #1 Time Schedule Error Output Setup Reader #1 Antipassback Error Output Setup RD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #2 Output Setup for Level 4 IDs Accessing Reader #2 Reader #2 Error Output SetupReader #2 ID Error Output Setup 12.RD2 ID Error Reader #2 Antipassback Error Output Setup Reader #2 Time Schedule Error Output Setup13.RD2 T/S Error Time Setup 14.RD2 APB Error Time Unit Setup Advanced setupOutput Time SCHEDULE+ID Time Unit Unit 1SEC Unit 0.1SEC Time Schedule Setup Antipassback ModeAPB Mode Not USE ALL Clear Use the 4 Buttons to specify the interval, day Holiday Setup Holiday Code Holiday Code SetupCode 01 Code 10 Reader #2 Mode Time Schedule Reader Mode Time Schedule Reader #1 Mode Time ScheduleRD1 Mode I T/S RD2 Mode I T/S Voice Message Time Schedule Output Time Schedule SetupVoice I T/S T/S Code ‘00’ means no Time Schedules are to be applied CUT OFF SET Input Time Schedule SetupInput CUT OFF Check Setup ID Display Additional featuresEvent Memory Setup Voice Volume Setup Wiegand Output SetupVoice Volume Wiegand Output not USE Not USE ONE Time Read Not USE Jnot USE Additional Features  The default setting for One Time Read is not USEONE Time Read Version Check Output Test Input Test LCD Test Last UpdateKeypad Test Press ANY KEY Reader Test RAM TESTING…Memory Test Reader Test SCANNING… Fingerprint Module Version Check Communication TestFailed If the test has succeeded If the test has failed O , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Input Type SetupInput Type Menu Structure Other information F3 button Menu Structure of the F3 buttonMenu Structure of the F4 button F4 button Other Information Menu Structure of the F5 buttonF5 button F6 button Menu Structure of the F6 button Menu Structure of the F8 button Menu Structure of the F7 button F9 button Menu Structure of the F9 buttonMenu Structure of the F10 button F10 button Output Settings for Input Sources Default SettingsDuress Alarm TTL#1 TTL#2 Output Setting for Authentication Trouble Shooting TroubleshootingTroubleshooting Communication between Buzzer keeps beepingController and the Host PC fails Software Product speciﬁcations Product Specifications Correct disposal of batteries in this product