Please visit our website | Samsung SSA-S3010/EXP instruction

SSA-S3010

SSA-S3011

SSA-S3020

SSA-S3021

SSA-S3040

SSA-S3041

Standalone Biometric

Access Controller

user manual

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service,

please visit our website.

www.samsungsecurity.com

Page 1

Image 1

Samsung SSA-S3010/EXP manual Standalone Biometric Access Controller, Please visit our website

Contents

Please visit our website Standalone Biometric Access Controller Safety information Safety information Safety Information Important Safety InstructionsThis device may not cause harmful interference, Contents Contents Wiegand Output Setup Event Memory SetupVoice Volume Setup Input Type Setup Product introduction Features Forced Door Open Alarm External I/O PinsDoor Open Timeout Alarm Duress Alarm Quick Guide CD Manual WHAT’S Included Front Panel AT a GlanceLCD Pin Connector Preliminary connector for extension Communication status indicatorRear Panel LED Pins Signal Cable Color PIN ConnectorCable Color Scheme Cable Selection TCP/IP RJ45 Connector Follow the instructions below to install the wall mount Installing the Wall Mount Bypass Diode Connection Connecting the Termination Resistor and Diode EARTH-GROUNDING the Communication Cables Input Connection Connection Output Connection External Reader Connection External Reader Connection RS-232 Communication Port Connection Communication Line Connection RS-485 Communication Port Connection Multiple Units RS-485 Communication Port Connection StandaloneMax m Please follow the steps below Connect all RS-485 ports of the product in parallel TCP/IP Communication Port Connection System Initialization in Master Mode Initializing the system using the Initialize switchInitialization Initializing the System Registering a Master ID To Access the Master ModeTo register a master card To register a master card PIN To register a master card along with your ﬁngerprint00/00 Lift PUT Your Finger To register a master card PIN along with your ﬁngerprint Name DisplayNot USE Language Setup User Count Setup Communication Address Setup DATE/TIME SetupSET DATE/TIME Comm Addr SET Factory Defaults Baud Rate SetupDefault SET Baud Rate Reader #1 Mode Reader mode setupReader #2 Mode READER#1 Mode ID only JID+F/PP/W RD#1 KEY Input not USE Reader Mode Setup € USE If set, you can get access using the keypad inputReader #1 KEY Input Reader #2 KEY Input Dual F/P Mode Jnot USE Dual F/P Mode USE Dual Fingerprint Mode Identification Mode Adaptive ModeAdaptive Mode not USE Jnot USE Adaptive Mode USE Mode Setup Identification Jnot USE User management Registering ID in Quick ModeTo register ID To register ID along with ﬁngerprint To register the ID card Registering the IDPW TA TB C RD MA MB LV FP User Management ID Registered To register the PIN number To register the ID card along with your ﬁngerprintTo select PIN SSA-S30x1 Numeric letters in 4 ~ 8 or 10 digits To register the PIN number along with your ﬁngerprint To Delete IDEnter PIN Screen ID List Viewing the ID List ALL ID Clear To Check the Number of Registered FingerprintsFP REG. Count Duress Mode Not USE Duress Password Enter Duress P/W Duress ModeTo delete all registered master IDs Master ID CLR ARM/DISARM Door Open Alarm Time SetupOpen ALR Time User Management ARM/DISARM SET To move to the TWO MEN Mode item TWO MEN Operation ModeTo Check the Number of Events To select USE or not USE, and press ENT . J not USE To Remove the Time Schedule To Remove ALL Events Door Contact Sensor Setup Time setupExit Button Output Exit Button Auxiliary Input #2 Setup Auxiliary Input #1 SetupTime Setup AUX INPUT#1 CUT OFF Output Setup Tamper Alarm Output SetupTamper Alarm CUT OFF Alarm ARM/DISARM Output Setup Duress Mode Output Setup RD1 ID OK LV1 Door Open Timeout Setup Output Setup for Level 3 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 ID Error Output Setup Reader #1 Error Output SetupReader #1 Time Schedule Error Output Setup Reader #1 Antipassback Error Output Setup RD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #2 Output Setup for Level 4 IDs Accessing Reader #2 Reader #2 Error Output SetupReader #2 ID Error Output Setup 12.RD2 ID Error Reader #2 Antipassback Error Output Setup Reader #2 Time Schedule Error Output Setup13.RD2 T/S Error Time Setup 14.RD2 APB Error Time Unit Setup Advanced setupOutput Time SCHEDULE+ID Time Unit Unit 1SEC Unit 0.1SEC Time Schedule Setup Antipassback ModeAPB Mode Not USE ALL Clear Use the 4 Buttons to specify the interval, day Holiday Setup Holiday Code Holiday Code SetupCode 01 Code 10 Reader #2 Mode Time Schedule Reader Mode Time Schedule Reader #1 Mode Time ScheduleRD1 Mode I T/S RD2 Mode I T/S Voice Message Time Schedule Output Time Schedule SetupVoice I T/S T/S Code ‘00’ means no Time Schedules are to be applied Input CUT OFF Check Setup Input Time Schedule SetupCUT OFF SET Event Memory Setup Additional featuresID Display Voice Volume Setup Wiegand Output SetupVoice Volume Wiegand Output not USE Not USE ONE Time Read Not USE Jnot USE Additional Features  The default setting for One Time Read is not USEONE Time Read Version Check Output Test Input Test LCD Test Last UpdateKeypad Test Press ANY KEY Reader Test RAM TESTING…Memory Test Reader Test SCANNING… Fingerprint Module Version Check Communication TestFailed If the test has succeeded If the test has failed Input Type Input Type SetupO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Menu Structure Other information F3 button Menu Structure of the F3 buttonMenu Structure of the F4 button F4 button F5 button Menu Structure of the F5 buttonOther Information F6 button Menu Structure of the F6 button Menu Structure of the F8 button Menu Structure of the F7 button F9 button Menu Structure of the F9 buttonMenu Structure of the F10 button F10 button Output Settings for Input Sources Default SettingsDuress Alarm TTL#1 TTL#2 Output Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Communication between Buzzer keeps beepingController and the Host PC fails Software Product speciﬁcations Product Specifications Correct disposal of batteries in this product