Rear Panel, Led | Samsung SSA-S3010/EXP instruction

Rear Panel

1	RJ45 Connector	Used in TCP/IP communications.

2	Tamper Switch	Tamper switch.

3	Fixing Hole	Hole for a ﬁxing screw.

4	2-pin Connector	Can be connected to the power cable.

5	3-pin Connector	Preliminary connector for extension.

6	6-pin Connector	Can be connected to the I/O cable.

7	8-pin Connector	Can be connected to the relay wiring cable.

8	Initialize switch	System Initialize switch.

9	LED	Communication status indicator.

10	4-pin Connector	Preliminary connector for extension.

11	5-pin Connector	Can be connected to the RS-232 and RS-485 communication cables.

PRODUCT INTRODUCTION

English _ 11

Page 11

Image 11

Samsung SSA-S3010/EXP Rear Panel, Led, Communication status indicator, Pin Connector Preliminary connector for extension

Contents

Please visit our website Standalone Biometric Access Controller Safety information Safety information This device may not cause harmful interference, Important Safety InstructionsSafety Information Contents Contents Input Type Setup Event Memory SetupWiegand Output Setup Voice Volume Setup Product introduction Features Duress Alarm External I/O PinsForced Door Open Alarm Door Open Timeout Alarm Quick Guide CD Manual WHAT’S Included LCD AT a GlanceFront Panel LED Communication status indicatorPin Connector Preliminary connector for extension Rear Panel Cable Color Scheme PIN ConnectorPins Signal Cable Color Cable Selection TCP/IP RJ45 Connector Follow the instructions below to install the wall mount Installing the Wall Mount Bypass Diode Connection Connecting the Termination Resistor and Diode EARTH-GROUNDING the Communication Cables Input Connection Connection Output Connection External Reader Connection External Reader Connection RS-232 Communication Port Connection Communication Line Connection Please follow the steps below RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Max m Connect all RS-485 ports of the product in parallel TCP/IP Communication Port Connection Initializing the System Initializing the system using the Initialize switchSystem Initialization in Master Mode Initialization To register a master card To Access the Master ModeRegistering a Master ID Lift PUT Your Finger To register a master card along with your ﬁngerprintTo register a master card PIN 00/00 Not USE Name DisplayTo register a master card PIN along with your ﬁngerprint Language Setup User Count Setup Comm Addr SET DATE/TIME SetupCommunication Address Setup SET DATE/TIME Baud Rate Baud Rate SetupFactory Defaults Default SET READER#1 Mode ID only JID+F/PP/W Reader mode setupReader #1 Mode Reader #2 Mode Reader #2 KEY Input € USE If set, you can get access using the keypad inputRD#1 KEY Input not USE Reader Mode Setup Reader #1 KEY Input Dual F/P Mode Jnot USE Dual F/P Mode USE Dual Fingerprint Mode Identification Jnot USE Adaptive ModeIdentification Mode Adaptive Mode not USE Jnot USE Adaptive Mode USE Mode Setup To register ID along with ﬁngerprint Registering ID in Quick ModeUser management To register ID PW TA TB C RD MA MB LV FP User Management ID Registered Registering the IDTo register the ID card SSA-S30x1 Numeric letters in 4 ~ 8 or 10 digits To register the ID card along with your ﬁngerprintTo register the PIN number To select PIN Screen To Delete IDTo register the PIN number along with your ﬁngerprint Enter PIN ID List Viewing the ID List FP REG. Count To Check the Number of Registered FingerprintsALL ID Clear Master ID CLR Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W To delete all registered master IDs ARM/DISARM SET Door Open Alarm Time SetupARM/DISARM Open ALR Time User Management To select USE or not USE, and press ENT . J not USE TWO MEN Operation ModeTo move to the TWO MEN Mode item To Check the Number of Events To Remove the Time Schedule To Remove ALL Events Exit Button Time setupDoor Contact Sensor Setup Exit Button Output AUX INPUT#1 Auxiliary Input #1 SetupAuxiliary Input #2 Setup Time Setup CUT OFF Alarm Tamper Alarm Output SetupCUT OFF Output Setup Tamper Alarm ARM/DISARM Output Setup Duress Mode Output Setup RD1 ID OK LV1 Door Open Timeout Setup Output Setup for Level 4 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 3 IDs Accessing Reader #1 Reader #1 Antipassback Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Time Schedule Error Output Setup RD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #2 12.RD2 ID Error Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 Reader #2 ID Error Output Setup 14.RD2 APB Error Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 13.RD2 T/S Error Time Setup Time Unit Unit 1SEC Unit 0.1SEC Advanced setupTime Unit Setup Output Time SCHEDULE+ID Use the 4 Buttons to specify the interval, day Antipassback ModeTime Schedule Setup APB Mode Not USE ALL Clear Holiday Setup Code 10 Holiday Code SetupHoliday Code Code 01 RD2 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD1 Mode I T/S T/S Code ‘00’ means no Time Schedules are to be applied Output Time Schedule SetupVoice Message Time Schedule Voice I T/S CUT OFF SET Input Time Schedule SetupInput CUT OFF Check Setup ID Display Additional featuresEvent Memory Setup Wiegand Output not USE Not USE Wiegand Output SetupVoice Volume Setup Voice Volume Version Check  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features ONE Time Read Output Test Input Test Press ANY KEY Last UpdateLCD Test Keypad Test Reader Test SCANNING… RAM TESTING…Reader Test Memory Test If the test has succeeded If the test has failed Communication TestFingerprint Module Version Check Failed O , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Input Type SetupInput Type Menu Structure Other information F4 button Menu Structure of the F3 buttonF3 button Menu Structure of the F4 button Other Information Menu Structure of the F5 buttonF5 button F6 button Menu Structure of the F6 button Menu Structure of the F8 button Menu Structure of the F7 button F10 button Menu Structure of the F9 buttonF9 button Menu Structure of the F10 button TTL#1 TTL#2 Default SettingsOutput Settings for Input Sources Duress Alarm Output Setting for Authentication Trouble Shooting TroubleshootingTroubleshooting Software Buzzer keeps beepingCommunication between Controller and the Host PC fails Product speciﬁcations Product Specifications Correct disposal of batteries in this product

Samsung SSA-S3010/EXP manual Rear Panel, Led, Communication status indicator

Models: SSA-S3010/EXP

Rear Panel

LED

Communication status indicator.

4-pin Connector

Preliminary connector for extension.