Event Memory Setup, ID Display, Input Test

ADDITIONAL FEATURES	61	Event Memory Setup
61	61	ID Display
61	62	WIEGAND Output Setup
	62	WIEGAND Output Setup
	62	Voice Volume Setup
	63	One Time Read
	63	Version Check
	64	Input Test
	64	Output Test
	65	LCD Test
	65	Keypad Test
	66	READER Test
	66	Memory Test
	67	Communication Test
	67	Fingerprint Module Version Check
	68	Input Type Setup
OTHER INFORMATION	69	Menu Structure
69	75	Default Settings
TROUBLESHOOTING	77	TroubleShooting
77
PRODUCT SPECIFICATIONS	79	Product Speciﬁcations
79

6_ contents

Page 6

Image 6

Samsung SSA-S3010/EXP Event Memory Setup, ID Display, Wiegand Output Setup, Voice Volume Setup, One Time Read, Input Test

Contents

Standalone Biometric Access Controller Please visit our website Safety information Safety information Important Safety Instructions Safety InformationThis device may not cause harmful interference, Contents Contents Voice Volume Setup Event Memory SetupWiegand Output Setup Input Type Setup Features Product introduction Door Open Timeout Alarm External I/O PinsForced Door Open Alarm Duress Alarm WHAT’S Included Quick Guide CD Manual AT a Glance Front PanelLCD Rear Panel Communication status indicatorPin Connector Preliminary connector for extension LED PIN Connector Pins Signal Cable ColorCable Color Scheme TCP/IP RJ45 Connector Cable Selection Installing the Wall Mount Follow the instructions below to install the wall mount Connecting the Termination Resistor and Diode Bypass Diode Connection EARTH-GROUNDING the Communication Cables Connection Input Connection Output Connection External Reader Connection External Reader Connection Communication Line Connection RS-232 Communication Port Connection Max m RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Please follow the steps below TCP/IP Communication Port Connection Connect all RS-485 ports of the product in parallel Initialization Initializing the system using the Initialize switchSystem Initialization in Master Mode Initializing the System To Access the Master Mode Registering a Master IDTo register a master card 00/00 To register a master card along with your ﬁngerprintTo register a master card PIN Lift PUT Your Finger Name Display To register a master card PIN along with your ﬁngerprintNot USE User Count Setup Language Setup SET DATE/TIME DATE/TIME SetupCommunication Address Setup Comm Addr SET Default SET Baud Rate SetupFactory Defaults Baud Rate Reader #2 Mode Reader mode setupReader #1 Mode READER#1 Mode ID only JID+F/PP/W Reader #1 KEY Input € USE If set, you can get access using the keypad inputRD#1 KEY Input not USE Reader Mode Setup Reader #2 KEY Input Dual Fingerprint Mode Dual F/P Mode Jnot USE Dual F/P Mode USE Adaptive Mode not USE Jnot USE Adaptive Mode USE Mode Setup Adaptive ModeIdentification Mode Identification Jnot USE To register ID Registering ID in Quick ModeUser management To register ID along with ﬁngerprint Registering the ID To register the ID cardPW TA TB C RD MA MB LV FP User Management ID Registered To select PIN To register the ID card along with your ﬁngerprintTo register the PIN number SSA-S30x1 Numeric letters in 4 ~ 8 or 10 digits Enter PIN To Delete IDTo register the PIN number along with your ﬁngerprint Screen Viewing the ID List ID List To Check the Number of Registered Fingerprints ALL ID ClearFP REG. Count To delete all registered master IDs Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W Master ID CLR Open ALR Time User Management Door Open Alarm Time SetupARM/DISARM ARM/DISARM SET To Check the Number of Events TWO MEN Operation ModeTo move to the TWO MEN Mode item To select USE or not USE, and press ENT . J not USE To Remove ALL Events To Remove the Time Schedule Exit Button Output Time setupDoor Contact Sensor Setup Exit Button Time Setup Auxiliary Input #1 SetupAuxiliary Input #2 Setup AUX INPUT#1 Tamper Alarm Tamper Alarm Output SetupCUT OFF Output Setup CUT OFF Alarm Duress Mode Output Setup ARM/DISARM Output Setup Door Open Timeout Setup RD1 ID OK LV1 Output Setup for Level 2 IDs Accessing Reader #1 Output Setup for Level 3 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 Time Schedule Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Antipassback Error Output Setup Output Setup for Level IDS Accessing Reader #2 RD2 ID OK LV2 Reader #2 ID Error Output Setup Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 12.RD2 ID Error 13.RD2 T/S Error Time Setup Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 14.RD2 APB Error Output Time SCHEDULE+ID Advanced setupTime Unit Setup Time Unit Unit 1SEC Unit 0.1SEC APB Mode Not USE ALL Clear Antipassback ModeTime Schedule Setup Use the 4 Buttons to specify the interval, day Holiday Setup Code 01 Holiday Code SetupHoliday Code Code 10 RD1 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD2 Mode I T/S Voice I T/S Output Time Schedule SetupVoice Message Time Schedule T/S Code ‘00’ means no Time Schedules are to be applied Input Time Schedule Setup Input CUT OFF Check SetupCUT OFF SET Additional features Event Memory SetupID Display Voice Volume Wiegand Output SetupVoice Volume Setup Wiegand Output not USE Not USE ONE Time Read  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features Version Check Input Test Output Test Keypad Test Last UpdateLCD Test Press ANY KEY Memory Test RAM TESTING…Reader Test Reader Test SCANNING… Failed Communication TestFingerprint Module Version Check If the test has succeeded If the test has failed Input Type Setup Input TypeO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Other information Menu Structure Menu Structure of the F4 button Menu Structure of the F3 buttonF3 button F4 button Menu Structure of the F5 button F5 buttonOther Information Menu Structure of the F6 button F6 button Menu Structure of the F7 button Menu Structure of the F8 button Menu Structure of the F10 button Menu Structure of the F9 buttonF9 button F10 button Duress Alarm Default SettingsOutput Settings for Input Sources TTL#1 TTL#2 Output Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Controller and the Host PC fails Buzzer keeps beepingCommunication between Software Product Specifications Product speciﬁcations Correct disposal of batteries in this product

contents

ADDITIONAL FEATURES

Event Memory Setup

ID Display

WIEGAND Output Setup

Voice Volume Setup

One Time Read

Version Check

Input Test

Output Test

LCD Test

Keypad Test

READER Test

Memory Test

Communication Test

Input Type Setup

Menu Structure

Default Settings

TroubleShooting

Product Speciﬁcations