Sharp AR-FX12 Storing a Program, Editing and Deleting Programs, Touch the Program Name key

STORING, EDITING, AND DELETING AUTO DIAL KEYS AND PROGRAMS

STORING A PROGRAM

You can store a destination fax number, speed dialing, polling, erase, dual page scan, 2in1, card shot, and resolution and exposure settings in a program. This enables you to call up the program and perform the transmission by means of a simplified operation. (See "USING A PROGRAM" on page 3-17.)

NOTE

A timer setting (page 3-6) cannot be included in a program.

When storing a program for an F-Code operation, one touch keys for destinations must include sub-addresses.

To store a program key, follow steps 1 through 3 on page 6-2, touch the [PROGRAM] key in step 4, and then follow these steps.

1 Touch the [PROGRAM NAME] key.

				The	"No."		that
PROGRAM
				automatically		appears is
	No.1
				the lowest number from 1 to
		PROGRAM NAME
				8 that has not yet been
		SETTINGS	ADDRESS	programmed.		When	the
				[PROGRAM NAME] key is
			RESOLUTION
				touched,	the	letter-entry

screen appears. Enter up to 18 characters for the name. Refer to chapter 7 of "Operation manual (for general information and copier operation)" for the procedure for entering letters.

2 Touch the [SETTINGS] key.

No.1

PROGRAM NAME PROGRAM FOR SHARP

SETTINGS ADDRESS

RESOLUTION

SPECIAL MODES

3 Touchstore. the keys for the settings you wish to

ENTER PROGRAM YOU REQUIRE.			CANCEL			OK
AUTO		FAX			ADDRESS BOOK
EXPOSURE
	MODE SWITCH
STANDARD				ADDRESS REVIEW
RESOLUTION
				SPECIAL MODES

For the detailed procedures for each of the settings, refer to the explanations of those features on the following pages.

[RESOLUTION](page 1-10)[EXPOSURE](page 1-11)[SPEED DIAL](page 2-4) [ADDRESS BOOK] (page 3-3)

[SPECIAL MODES]

ERASE (page 3-4) DUAL PAGE SCAN (page 3-5)

2in1 (page 3-7)CARD SHOT (page 3-8)POLLING (page 3-13)

NOTE

Up to 500 (maximum of 300 on the AR-M351U/AR- M451U) destinations can be stored in a program. However, you cannot directly enter fax numbers with the numeric keys. A destination must be programmed in an auto dial key (one-touch key or group key) before it can be stored in a program.

4 Touch the [OK] key.

		Your settings are displayed. Make sure
5 they are correct.
	PROGRAM							NEXT		EXIT
		No.1	REGISTRATION
		PROGRAM NAME		SHARP PROGRAM
		SETTINGS			ADDRESS	2 ADDRESSES
					RESOLUTION	FINE	EXPOSURE		AUTO
					SPECIAL MODES	DUAL PAGE SCAN

6 When you are finished, touch the [EXIT] key. If you wish to store another program, touch the [NEXT] key.

Touching the [EXIT] key returns you to the screen of step 4 on page 6-2.

Touching the [NEXT] key returns you to the screen of step 1.

EDITING AND DELETING PROGRAMS

To edit or delete a previously stored program, follow steps 1 to 3 on page 6-2, touch the [AMEND/DELETE] key in the screen of step 4, and then follow these steps.

1 Touch the [PROGRAM] key.

2 Touch the program you wish to edit or delete.

1/2

EXIT

PROGRAM

DIRECT ADDRESS / AMEND/DELETE	EXIT
SELECT ADDRESS TO AMEND/DELETE.
PROGRAM	ADDRESS BOOK
PROGRAM FOR SHARP	EMAIL NEWS GROUP
ABYS FAX FORMAT A

When you touch the program name, the edit/delete screen for the selected program appears. Touching the [ADDRESS BOOK] key returns you to the screen of step 1.

3 To edit the program, follow the same procedure as for storing the program. To delete the program, touch the [DELETE] key and then touch the [YES] key in the confirmation screen that appears.

6-8